Best Three Phase Oil immersed Power

FLUKE-3540 FC KIT Three-Phase Power Monitor & Condition Monitoring Kit

power including active power, non-active power, and power factor.
Remote access to measurements via the Fluke Connect Condition Monitoring software.
Graphs show trends and fluctuations of the measurements during the monitoring period.
and alarm settings notify users when measurement values are outside user-set thresholds.
3540 FC Three-Phase Power Monitor is portable, wireless, battery powered, and easy to install.

power including active power, non-active power, and power factor.
Remote access to measurements via the Fluke Connect Condition Monitoring software.
Graphs show trends and fluctuations of the measurements during the monitoring period.
and alarm settings notify users when measurement values are outside user-set thresholds.
3540 FC Three-Phase Power Monitor is portable, wireless, battery powered, and easy to install.

Motor Speed Controller Brushless Controller with Hall-less.Full SMD process,stable performance,humanized design, interface all adopts terminal blocks..
"Voltage 5-50V high power 380W DC three-phase high-speed brushless sensorless controller. ".
Standard heat sink,onboard speed regulating potentiometer，you can use it when you have power on..
DC three-phase high-speed brushless sensorless controller recognizes PWM signal input, amplitude 3-5V supports PLC0-5V analog quantity, input control.
"Size-Length 63MM * width 45MM * height 31MM,Over-temperature protection:yes (half the over-temperature power) Maximum speed:224000 RPM (2 pole motor),74000 RPM (6 pole motor),40000 RPM (12 pole motor), 35000 RPM (14 pole motor).".

ATO 110v vfd, single phase 110v/120v input, single phase or three phase 220v output, achieve to run 220v AC motor on single phase 110v/120v power supply.
【Voltage& Frequency】Input voltage: 1 phase 120V AC ±15%, Input frequency: 50Hz/60Hz,Output voltage: 1 phase or 3 phase 220V AC ±15%, Output frequency: 0.00~400.00Hz.
【APPLICATION】ATO 7.5 hp 5.5kW variable frequency drive Can be widely applied to drive the AC motor, such as fans, pumps, power tools, etc.
【TIPS】 To protect the variable frequency drive and Motor, you need an upstream protection, add a line-choke upstream the VFD, this will reduce the current transients seen by the input of the VFD.
【CUSTOMER FIRST】If you have no experience in driving a VFD, be sure to refer to the instructions before operating a VFD.If you are not sure about the size or have any issue about the product or service, please don't hesitate to email us. We will answer you within 12h.

Function: Three-phase monitoring of phase sequence, phase loss..
Application: This monitoring relay is suitable for pumps, fans, blowers, motor elevators, cranes, central air conditioners, etc..
Construction and installation: This phase sequence relay uses standard modular construction and rail-mounted mounting..
Power supply mode: Powered by the measurement circuit, no additional auxiliary power supply is required..
Accessories: With 2 indicators to indicate various working conditions, the two groups usually open/close contacts..

★ The ideal gift for children and adults-high-end 3D VR Headset, virtual reality VR glasses. Compatible with smartphones and other mobile phone....
★ VR Headset smartphones are compatible with 4.7-6.2 inch iPhones and Android phones.
VR glasses for iPhone X 8 7 plus/6s/6/6 plus.
★ The new 2020 3D VR Headset headphones can be adjusted freely to expand the viewing angle and perfectly match the focal length and unilateral....
★ Updated resin aspheric lens, super comfortable ergonomic design-we Virtual Reality Headset provide soft and comfortable leather padding, three....
★ HIFI stereo headset: equipped with high-quality stereo headset and 3D phase sound technology, can bring you a three-dimensional immersive....

Dynamic phase loss, static phase loss protection: refers to the phase failure of any phase when the protected device is in the running state or non-operating state. The indicator light is in the form of red light and priority.
Wrong phase protection: A protection measure to prevent the phase sequence of L1, L2, L3 three-phase AC power supply from being connected incorrectly. Instant action. The indicator light is in the form of yellow light..
Voltage Unbalance Protection: Refers to a voltage imbalance that will affect the safe operation of the device. When the voltage imbalance rate is higher than 8%. The form of the indicator light is: the lack of phase red light is on, and priority..
Delay protection: When there is a fault, the monitor will delay after 1~2 seconds, and the relay will release..
The protection function of the monitor is not affected by the current of the line or load, the inrush current, the unbalanced current and the nature of the load. Long-term work with full performance and full climate. Power consumption is no more than 2W..

Dynamic phase loss, static phase loss protection: refers to the phase failure of any phase when the protected device is in the running state or non-operating state. The indicator light is in the form of red light and priority.
Wrong phase protection: A protection measure to prevent the phase sequence of L1, L2, L3 three-phase AC power supply from being connected incorrectly. Instant action. The indicator light is in the form of yellow light..
Voltage Unbalance Protection: Refers to a voltage imbalance that will affect the safe operation of the device. When the voltage imbalance rate is higher than 8%. The form of the indicator light is: the lack of phase red light is on, and priority..
Delay protection: When there is a fault, the monitor will delay after 1~2 seconds, and the relay will release..
The protection function of the monitor is not affected by the current of the line or load, the inrush current, the unbalanced current and the nature of the load. Long-term work with full performance and full climate. Power consumption is no more than 2W..

Dynamic phase loss, static phase loss protection: refers to the phase failure of any phase when the protected device is in the running state or non-operating state. The indicator light is in the form of red light and priority.
Wrong phase protection: A protection measure to prevent the phase sequence of L1, L2, L3 three-phase AC power supply from being connected incorrectly. Instant action. The indicator light is in the form of yellow light..
Voltage Unbalance Protection: Refers to a voltage imbalance that will affect the safe operation of the device. When the voltage imbalance rate is higher than 8%. The form of the indicator light is: the lack of phase red light is on, and priority..
Delay protection: When there is a fault, the monitor will delay after 1~2 seconds, and the relay will release..
The protection function of the monitor is not affected by the current of the line or load, the inrush current, the unbalanced current and the nature of the load. Long-term work with full performance and full climate. Power consumption is no more than 2W..