Best Stepper Motors And Drivers

Dr.Roc Compatible Instrument Cluster Gauge Stepper Motor Repair Kit Fits X27 168 03 to 06 with 7 Stepper Motors Soldering Iron Solder Sucker Chevy Silverado GM GMC

  • The latest generation,Premium stepper motor,quiet operation and reliability,Perfectly Replace for the older and faulty XC5-168( XC5168 ), X15-168( X15168 ) ,X25-168 ( X25168 ) and X27-168 ( X27168 , X27.168 , X27 168 ) stepper motor that came in your vehicles,Use the tool on the upper left corner to check whether this product fits your vehicles.
  • Stepper motor is used for repairing guage cluster,including speedometer,tachometer,oil pressure gauge,transmission temperature gauge, battery voltage gauge, water temperature gauge or fuel gauge.
  • Solve the common problems of your vehicle such as, gauges cluster dead,chatter,sticking,false/jumpy/inaccurate readings,pegged out to the left or right of the dial, ratchet up or down,sticky needle movement,erratic gauge movement etc.
  • Each gauge of your instrument cluster need one stepper motor.Since one stepper motor went out,and it will result all other stepper motors go out soon. Checking the quantity of stepper motors for your vehicle to decide to buy the 6 or 7 one.It is easy to use for upgraded adjustable soldering iron,but you’d better to search the instructions Video on Internet first,which is very helpful..
  • The premium instrument cluster repair kit is compatible with Silverado,Suburban,Traiblazer,Tahoe,Avalanc....
Check Stock

Aoicrie MKS Gen L V1.0 3D Printer Integrated Mainboard Controller PCB Board Compatible Ramps1.4/Mega2560 R3 with A4988 Motor Driver for 3D

  • ...arlin firmware,same as configuration way as Ramps1.4, it can replace Ramps1.4 directly..
  • Use high quality MOSFET tube,better cooling and more stable.Use special power chip,support 12-24V input,reduce the heated bed current to 1/4 that slove the Mosfet heat problem efficiently and power shortage..
  • Support a variety of stepper drivers: A4988,DRV8825,TMC2208 and TMC2100, and available to work with LCD2004,LCD12864,MKS TFT24/28/32/35 & Available to connect external large stepp drivers, A4988 driver board widely used in 3D printers and small CNC machines..
  • Support functions: Non-trace resumption after power off, run out filament ,and auto shut down, XTZ axis with different color terminal controls the motors and end stop,which is convenient to wire.Use high-quality 4 layer PCB&Use special power chip.Retail Servos,AUX-1 and AUX-2 interface of Ramps1.4 provide three 5V output and three 12V output interfaces..
  • Five different step resolutions: full-step, half-step, quarter-step, eighth-step, and sixteenth-step.Adjustable current control lets you set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor's rated voltage toachieve higher step rates.Use the configuration file to set the driving current mode, avoid manual....
Check Stock

Stepper Motor Mounting Bracket, 6pcs Steel Motor Mounting Nema17 Bracket, with Mounting Screws

  • Mounts are thick 2mm metal bent into an L shape. spot-welded 2 little triangle-shaped wedges in the corners. Ideal for replacement applications..
  • Stepper motor bracket durable alloy steel provides strong bearing pressure when printing..
  • Nema17 brackets are 2 long slots so you could easily loosen screws, tighten the belt tension of the motor and belt, and tighten them back down easily..
  • Stepper motor alloy steel mounting bracket can match standard Nema 17 stepper motor, and also include the mounting holes for Nema 17 economy planetary geared stepper motor but not for high precision planetary geared stepper motor..
  • 6 pcs of NEMA 7 stepper motor mounting brackets, 90 degrees L-shaped bracket there are 4 holes drilled to mount for 3D Printer Motors Nema 17 Stepper Motor 42-40 Motor..
Check Stock

AOICRIE 4PCS L298N Motor Drive Controller Board Module Dual H Bridge DC Stepper for Arduino

  • L298N as Main driver chip L298N, strong driving ability, strong anti-interference, low calorific value, afterflow diode protection, more stable and reliable for Arduino projects, Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability..
  • Double H bridge design, can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors, high efficient, To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage..
  • Driving DC motor Because the module is drived by double H bridge,it can drive two motors simultaneously.Input the following driving timing from IN1-IN4 then the speed and direction of the stepper motor can be controlled..
  • Easy to Use No assembly required. This L298N board comes ready to go. Just wire up motors and power, easy to use..
  • Wide Usage Great for DIY Smart Car Robot Power MEGA R3 for Mega2560 Duemilanove, if driving voltage is more than 12V, use external standard 5volt TTL outputs to switch the H-bridge circuits..
Check Stock

BIGTREETECH TMC2208 V3.0 UART Mode Stepper Motor Driver 3D Printer Parts 4 PCS

  • The TL-Smoother is an addon module for 3D printer stepper motor drivers.
  • Lower vibration lower noise smoother result.
  • The board provides flyback diodes (freewheeling diodes) for the motor outputs.
  • Also protected against induction voltages in the unpowered state of the driver.
  • You will got smoother movement especially on the delta-style 3Dprinter under DVR8825 stepper drivers and A4988/2 drivers.
Check Stock

18/4 AWG Shielded CNC Wire (50FT) — Flexible Stranded Shielded 18-Gauge 4-Conductor Cable for Stepper Motors, CNC Machines, NEMA Motors, VFD Spindles, CNC Routers, 3D Printers and more!

  • RESILIENT & FLEXIBLE: Stepper motor cable designed to bend smoothly in your CNC or 3D printer chain!.
  • SHIELDED 4 CONDUCTOR WIRE: Reduce interference for your CNC spindle motor or stepper motor driver!.
  • BEST RESULTS: Shielded wire means higher quality for your 3D Printer, CNC Machine or CNC Controller..
  • GREAT FOR All STEPPER MOTORS: Nema 17 Stepper Motor, Nema 23 Stepper Motor, Stepper Driver, & more!.
  • STEPPER MOTOR WIRE: The perfect upgrade to any CNC Kit, CNC Router Kit, or CNC Stepper Motor Kit..
Check Stock

Dr.Roc GM Instrument Cluster Gauge Stepper Motor Repair Kit X27 168 7 Motors,10 Backlight Bulbs,1 Remove Tool,Flux Rosin Core Solder

  • The latest generation,Premium stepper motors,quiet operation and reliability,Perfectly Replace for the older and faulty XC5-168, X15-168 ,X25-168 and....
  • Used for the repair of the speedometer,tachometer,oil pressure gauge,transmission temperature gauge, battery voltage gauge, water temperature gauge or....
  • Each gauges of your instrument cluster need one motor,since one stepper motor went out will result all the motors go out soon. check the stepper motor....
  • It is easy to use,but you’d better to search the instructions Video on Internet first,which is very helpful.
  • Dr.Roc-Most trusted auto accessories expert,millions buyers' choice, excellent customer service with 12-month warranty.
Check Stock

6Pcs L298N Motor Drive Controller Board DC Dual H-Bridge Stepper Motor Control and Drives Module for Arduino Micro:bit Smart Car Robot UNO MEGA R3 Mega2560

  • ★L298N as main driver chip makes strong driving ability and strong anti-interference,dual-channel h-bridge driver working mode creates higher working efficiency,,drive stepper dc motors to work.to avoid damage the voltage stabilizing chip, please use an external 5v logic supply when using more than 12v.
  • ★Dual-channel H-bridge driver working mode creates higher working efficiency..
  • ★To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage..
  • ★Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability..
  • ★L298N as main chip. Can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors..
Check Stock

Twotrees Stepper Motor Driver, TB6600 4A 9-42V Nema 17/23 CNC Controller Single Axes Hybrid - Upgraded Version

  • 【1】Package included: 1 x Stepper Motor Driver,1 x Stepper Motor, 1 x Wire..
  • 【2】Suitable for a wide range of stepper motors from NEMA size 17,23 and 24 (42 * 42mm to 60 * 60mm). It can be used in various types of machines, such as XYZ tables, labellers, laser cutters, engraving machines, pick-place devices and so on..
  • 【3】Motor driver: 9V-42V DC power supply, H-bridges bipolar constant phase current drive. The maximum 4.0A of the eight types of output current..
  • 【4】The largest 32 divisions of the 6 models are optional.
  • Suitable for 4 wires, 6 wires and 8 wires stepper motor..
  • 【5】Protect form: Overheated protection, overcurrent protection, undervoltage protection, prevention of inversion..
Check Stock