Best Stepper Drivers

Aoicrie MKS Gen L V1.0 3D Printer Integrated Mainboard Controller PCB Board Compatible Ramps1.4/Mega2560 R3 with A4988 Motor Driver for 3D

...arlin firmware,same as configuration way as Ramps1.4, it can replace Ramps1.4 directly..
Use high quality MOSFET tube,better cooling and more stable.Use special power chip,support 12-24V input,reduce the heated bed current to 1/4 that slove the Mosfet heat problem efficiently and power shortage..
Support a variety of stepper drivers: A4988,DRV8825,TMC2208 and TMC2100, and available to work with LCD2004,LCD12864,MKS TFT24/28/32/35 & Available to connect external large stepp drivers, A4988 driver board widely used in 3D printers and small CNC machines..
Support functions: Non-trace resumption after power off, run out filament ,and auto shut down, XTZ axis with different color terminal controls the motors and end stop,which is convenient to wire.Use high-quality 4 layer PCB&Use special power chip.Retail Servos,AUX-1 and AUX-2 interface of Ramps1.4 provide three 5V output and three 12V output interfaces..
Five different step resolutions: full-step, half-step, quarter-step, eighth-step, and sixteenth-step.Adjustable current control lets you set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor's rated voltage toachieve higher step rates.Use the configuration file to set the driving current mode, avoid manual....

Check Stock

BIGTREETECH Direct Octopus V1.1 Silent 32 Bit Control Board 3D + TFT35 E3 V3.0 Two Mode Display Screen 3D Printer Parts for Creality Ender 3/5 CR10

【Main Control Chip】Uses a 32-bit ARM Cortex-M4 series STM32F446ZET6 main control chip with a core frequency of 180MHz..
【Strong DIY Support】This motherboard supports up to 8 stepper drivers with 9 stepper driver outputs in total.
【Realize Online Printing】Interfaces with a Raspberry Pi using emulated serial over USB or direct UART to any of the serial ports on the board, to....
【Motherboard Expansion Function】Support BLTouch, locked-rotor detection, shutdown after printing, resume printing after power failure, CAN bus, U....
【Increase Protection Function】Uses high-performance MOSFETs to increase heating efficiency while also reducing heat generation on the motherboard.....

Check Stock

Duet 3 Mini 5+ WiFi 3D Printer Controller

Powerful 32 Bit Processor (ARM Cortex M4 @120Mhz).
Dedicated High speed bus to a single board computer (e.g. Raspberry Pi) for the user interface and plugins.
5 Trinamic 2209 stepper drivers running at up to 1.4A RMS, 2A peak with firmware control of the full feature set including up to 256 microstepping,....
All common 3D printer geometries are supported.
Support for a wide range of Z probes including DC42’s IR Z probe and the Duet3D Smart Effector for delta printers.

Check Stock

BIGTREETECH Octopus Pro V1.0 Controller Board New Upgrade with Octopus 32bit Motherboard Compatible TMC5160 Pro Stepper Driver Support Powerful DIY for 3D Printer Main Chip is STM32F446ZET6

【Main Control Chip】The main control adopts the 32-bit ARM Cortex-M4 series STM32F446ZET6 chip with a frequency of up to 180 MHz. The external....
【About Using Firmware】Support the use of Marlin2.0, killper, RRF three types of firmware. Please note: STM32F446ZET6 MCU flash memory space is....
【Stepper Motor】The Octopus Pro 3D printing motherboard can support up to 8 stepper motor drivers, and the motor drive power supply supports up to....
【Support Proximity Sensor】Support proximity sensor, jumper optional pull-up resistor, support more models. This function can be sensed without....
【High Temperature Test】The onboard MAX31865 can support 2/4-wire PT100/PT1000 temperature measurement without welding (the soldering resistance....

Check Stock

Creality 48CM TF to Micro SD TF Extension Cable Memory Card Adapter for/Raspberry Pi/Arduino GPS TV SDXC Creality CR10/10S/S4/S5/Ender 3/Ender 3 Pro Monoprice Select Mini 3D Printer

【Main Control Chip】Uses a 32-bit ARM Cortex-M4 series STM32F446ZET6 main control chip with a core frequency of 180MHz..
【Strong DIY Support】This motherboard supports up to 8 stepper drivers with 9 stepper driver outputs in total.
【Realize Online Printing】Interfaces with a Raspberry Pi using emulated serial over USB or direct UART to any of the serial ports on the board, to....
【Motherboard Expansion Function】Support BLTouch, locked-rotor detection, shutdown after printing, resume printing after power failure, CAN bus, U....
【Increase Protection Function】Uses high-performance MOSFETs to increase heating efficiency while also reducing heat generation on the motherboard.....

Check Stock

MKS Gen L V2.1 3D Printer Integrated Motherboard Controller PCB Board A4988/DRV8825/TMC2208/TMC2130 Like Ramps 1.6 MKS Gen V1.4 Mainboard

Integrate 2560 and Ramps1.4 one PCB,easier wiring and more stable..
Use high-quality 4 layer PCB&Use special power chip,support 12V-24V, also Use Marlin firmware,same as configuration way as Ramps1.4, it can replace Ramps1.4 directly..
Support a variety of stepper drivers:4988,8825,TMC2208 and TMC2100, and available to work with LCD2004,LCD12864,MKS..
TFT24/28/32/35 & Available to connect external large stepp drivers Accept 24V input,reduce the heated bed current to 1/4 that slove the Mosfet heat problem efficiently..
Retail Servos,AUX-1 and AUX-2 interface of Ramps1.4 provide three 5V output and three 12V output interfaces..

Check Stock

Doesbot GRBL 1.1 CNC Engraving Machine Control Board 3 Axis Control Laser Engraving Machine Board TMC2208 Mute Drivers

Board with 1.6MM high-quality A-plate, reliable and stable..
Provide technical support, easy to get started..
Input voltage (board power supply): 12V to 24V.
Integrated 3 TMC2208 Mute Drivers, directly connect to four wire stepper motor..

Check Stock

MKS Gen L V2.0 3D Printer Integrated Motherboard Controller PCB Board A4988/DRV8825/TMC2208/TMC2130 Like Ramps 1.6 MKS Gen V1.4 Mainboard 1PCS

❤️ Integrate 2560 and Ramps1.4 one PCB,easier wiring and more stable.
❤️Use high-quality 4 layer PCB&Use special power chip,support 12V-24V, also Use Marlin firmware,same as configuration way as Ramps1.4, it can replace Ramps1.4 directly.
❤️ Support a variety of stepper drivers:4988,8825,TMC2208 and TMC2100, and available to work with LCD2004,LCD12864,MKS.
❤️TFT24/28/32/35 & Available to connect external large stepp drivers Accept 24V input,reduce the heated bed current to 1/4 that slove the Mosfet heat problem efficiently.
❤️Retail Servos,AUX-1 and AUX-2 interface of Ramps1.4 provide three 5V output and three 12V output interfaces.

Check Stock

Mini Stepper with Resistance Bands Exercise Step Machine Portable Stair Stepper with LCD Display, 250 LBS Weight Capacity

【Height Adjustment】The height adjustment knob of stepper exercise machine can adjust the height of short pulse or long step movement.Mini stepper is easy to use in any indoor or outdoor places, such as home, office, providing a comfortable and efficient training sessions for adult women kids.This stepper exercise machine is fully assembled and space-saving..
【Hydraulic Drive System】The steppers for exercise has a built-in hydraulic drive system,which can provide smooth stepping movement.The internal super-energy spring that protects the joints and provides a good cushioning effect.The Double hydraulic balance of stepper is evenly loaded,all-metal support,strong pressure resistance.Pay attention that the hydraulic tube of stepper exercise machine need rest after 20-minutes..
【LCD Display】The steppers for exercise come with professional display.LCD monitor of stepper measures the steps,time,total and calories,making your exercise more reasonable and effective,and achieve the ultimate goal of weight loss.The screen on the monitor is bigger than other stepper exercise machine.It is convenient for you to know your exercise situation and make your next exercise plan..
【Professional Fitness Coach】The steppers for exercise with removable trainin....

Check Stock