Best Scope Rings For Picatinny Rail

Monstrum Extended Series Offset Picatinny Scope Mount | 30 mm Diameter | 20 MOA | Black

  • Built specifically for long range scopes – 6-24x magnification scopes and above – with 3 inches of spacing between scope rings to accommodate scopes with longer dimensions and larger adjustment housing.
  • Lightweight one-piece scope mount for mounting standard 30 mm diameter tube rifle scopes – with weight comparable to a set of lightweight rings, while providing the added rigidity and convenience of a one piece mount.
  • Mounts to any flat top Picatinny rail equipped rifle with custom Picatinny locking bolts that slot seamlessly into your Picatnny rail with zero wiggle – guaranteed to hold zero against the toughest of recoil.
  • Available in three styles – a 0 MOA mount for zeroing your scope at short to mid range distances, a 20 MOA mount for zeroing your scope at longer distances, and a 30 MOA mount for serious long distance shooters..
  • Mount frame crafted from lightweight 6061 grade aluminum with hardened steel Torx mounting hardware to prevent stripping of the bolts.
Check Stock

Monstrum Picatinny/Weaver Rail Mount for Marlin 336/1894/1895 Series Lever Action Rifles with Integrated Level Bubble | 0 MOA

  • Picatinny/Weaver rail mount built specifically for Marlin 336/1894/1895 Series lever action rifles.
  • Scope mount installs directly to receiver via the factory mounting holes and included set screws with no additional hardware required.
  • Allows for the mounting of Picatinny or Weaver standard scope rings, scope mounts, red dots, or other optics.
  • Integrated level bubble built into the rear of the rail to check for consistent vertical alignment of your rifle.
  • All Monstrum scope mounts and accessories come with a lifetime guarantee.
Check Stock

Modkin Scope Rings, Rifle Scope Mount High Profile Scope Mounts for Picatinny Rail (1 inch, Set of 2)

  • Double scope ring mount for Picatinny/ Weaver Rail (21mm)..
  • Design in hollowed-out configuration between the ring and the bottom of the base, to release heavy duty when clamping your scope..
  • Built-in tape inside per rings to prevent from marring the scope, also prevent sliding and holding postion accurately..
  • The ring is for most scopes which are in 1 inch / 25.4mm scope tube. High profile, 0.71 inch gap from base of mount to bottom of rings. ( Item height: 2 inch).
  • With 1 rail clamp screw and 2 scope clamp screw per side, ensure mount any 1 inch scope firmly, just twist off the nut and mount the base on the 21mm rail easily..
Check Stock

Monstrum Precision Picatinny Scope Rings | 1 inch Diameter | 0.80 inch Height

  • 0.80 inches in height, measured from the center of the rifle scope tube to the bottom plane of the Picatinny rail mount.
  • Monstrum Tactical Precision Scope Rings are precision crafted to a given height specification to match your particular rifle setup and preferred cheek....
  • 1 inch diameter rings for mounting standard 1 inch rifle scope tubes.
  • Base is compatible with Picatinny mounting systems | Not compatible with Weaver mounts.
  • Available in four heights to match your needs: 0.80 inch, 1.00 inch, 1.20 inch, and 1.35 inch.
Check Stock

Monstrum Precision Picatinny Scope Rings | 1 inch Diameter | 1.00 inch Height

  • 1.00 inches in height, measured from the center of the rifle scope tube to the bottom plane of the Picatinny rail mount.
  • Monstrum Tactical Precision Scope Rings are precision crafted to a given height specification to match your particular rifle setup and preferred cheek weld.
  • 1 inch diameter rings for mounting standard 1 inch rifle scope tubes.
  • Base is compatible with Picatinny mounting systems | Not compatible with Weaver mounts.
  • Available in four heights to match your needs: 0.80 inch, 1.00 inch, 1.20 inch, and 1.35 inch.
Check Stock

Monstrum Precision Picatinny Scope Rings | 1 inch Diameter | 1.20 inch Height

  • 1.20 inches in height, measured from the center of the rifle scope tube to the bottom plane of the Picatinny rail mount.
  • Monstrum Tactical Precision Scope Rings are precision crafted to a given height specification to match your particular rifle setup and preferred cheek weld.
  • 1 inch diameter rings for mounting standard 1 inch rifle scope tubes.
  • Base is compatible with Picatinny mounting systems | Not compatible with Weaver mounts.
  • Available in four heights to match your needs: 0.80 inch, 1.00 inch, 1.20 inch, and 1.35 inch.
Check Stock

Monstrum Extended Series Offset Picatinny Scope Mount for Long Range Scopes | 1 inch Diameter | Black

  • Built specifically for long range scopes - 6-24x magnification scopes and above - with 3 inches of spacing between scope rings to accommodate scopes....
  • Lightweight one-piece scope mount for mounting standard 1 inch diameter tube rifle scopes - with weight comparable to a set of lightweight rings,....
  • Mounts to any flat top Picatinny rail equipped rifle with custom Picatinny locking bolts that slot seamlessly into your Picatnny rail with zero wiggle....
  • 2 inches of forward extension allows extra flexibility for optimum eye relief and shooting position.
  • Mount frame crafted from lightweight 6061 grade aluminum with hardened steel Torx mounting hardware to prevent stripping of the bolts.
Check Stock

Monstrum Precision V2 Picatinny Scope Rings | 34 mm Diameter | 1.40 inch Height

  • 1.35 inches in height, measured from the center of the rifle scope tube to the bottom plane of the Picatinny rail mount.
  • 34 mm diameter rings for mounting standard 34 mm rifle scope tubes.
  • Picatinny mount base mechanism comes equipped with custom Picatinny locking bolts that slot seamlessly into your Picatnny rail with zero wiggle - guaranteed to hold zero against the toughest of recoil | Not compatible with Weaver mounts.
  • Uses hardened steel Torx mounting hardware to prevent stripping of the bolts.
  • Available in four different heights to match the needs of any shooter: 0.85 inch, 1.00 inch, 1.20 inch, and 1.35 inch.
Check Stock

Monstrum Precision V2 Picatinny Scope Rings | 34 mm Diameter | 1.00 inch Height

  • 1.00 inches in height, measured from the center of the rifle scope tube to the bottom plane of the Picatinny rail mount.
  • 34 mm diameter rings for mounting standard 34 mm rifle scope tubes.
  • Picatinny mount base mechanism comes equipped with custom Picatinny locking bolts that slot seamlessly into your Picatnny rail with zero wiggle - guaranteed to hold zero against the toughest of recoil | Not compatible with Weaver mounts.
  • Uses hardened steel Torx mounting hardware to prevent stripping of the bolts.
  • Available in four different heights to match the needs of any shooter: 0.85 inch, 1.00 inch, 1.20 inch, and 1.35 inch.
Check Stock