Best 5v Relay Current Ratings

NOYITO 0-5A AC Current Detection Sensor Module Switch Output (DC 12V, Green)

Current detection range: AC 0-5A.003cbr003e.
Operating voltage: DC 5V / 12V / 24V ± 0.2V. (Select the corresponding version of the product according to your needs).003cbr003e.
Output mode: relay switching output.003cbr003e.
Relay load: AC 250V 10A Max , DC 30V 10A Max.003cbr003e.
Application: Intelligent trolley motor over-current detection, motor stall protection current detection, short-circuit protection detection, etc. (The second picture on the left is the schematic and the third picture is the wiring diagram)003cbr003e.

It is 4 Channel Isolated 5V 10A Relay Module, each relay can individually switch on/off by an opto-isolated digital input, Standard interface can be directly connected with microcontrollers and be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, DSP, etc., very convenient..
Equipped with high-current relay, maximum load: AC250V 10A, 15A 125VAC, DC30V 10A.
RELIABLE: Fault-tolerant design, even if the control line breaks, the relay will not move.
With optical coupling isolation, triggering more reliable, more stable..
EASY to INSTALL: Equipped with screwed terminal plate and fixed bolt holes(diameter: 3.1 mm) on both sides for easy installation..
High/Low level trigger can be selected by jumper. Very versatile, you can reverse the input logic with the jumper..

5V 2-Channel Relay interface board, and each one needs 15-20mA Driver Current.
Equiped with high-current relay, AC250V 10A.
Standard interface that can be controlled directly by microcontroller (compatible with Arduino ,Raspberry Pi, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic).
Indication LED's for Relay output status.
Size: 50.5mm(L) x 38.5mm(W) x 18.5mm(H)(1.99inch x 1.54inch x 0.73inch).

30A High Current 12V Contactor relay Switch DC power Switching Control Board.
Using high-quality ultra-small optocoupler, anti-interference ability, stable performance..
Using 9.5mm black fence terminal, standard 30A terminal, stable and solid, reliable quality..

30A High Current 12V Contactor relay Switch DC power Switching Control Board.
Using high-quality ultra-small optocoupler, anti-interference ability, stable performance..
Using 9.5mm black fence terminal, standard 30A terminal, stable and solid, reliable quality..

◇ ANTI-INTERFERENCE---Made of the high quality miniature optocoupler, the relay module is of anti-interference ability, stable performance.
◇ STABLE AND RELIABLE---Adopting 9.5mm black barrier terminal and standard 30A terminal, the relay module is stable and reliable.
◇ HIGH/LOW LEVEL TRIGGER---The high/low level trigger of the relay module can be switched.
◇ DC5V/DC12V/DC24V---There are 3 styles for you: DC5V, DC12V, DC24V, you can choose one according to your preference.
◇ MAIN FEATURE---Product Name: Optocoupler Isolation Relay Module.
Output Capability: AC 250V/30A, less than DC 30V/30A.

This is a simple and practical passive relay module, which is very convenient to use. It can support both Normally Open and Normally Close..
Input control signal: AC/DC 5V, AC/DC 12V, AC/DC24V, AC/DC48V, AC 115V, AC 230V Selectable..
Output switch DPST 1NO 1NC(Double Pole Single Throw, 1x Normally Open and 1x Normally Close ), rated current 8A/250VAC or 8A/30VDC (one switch)..
Compact ABS plastic case and wires connect for easy mount. Two screw mounting holes are convenient for you to fix it on the wall or wooden board. Of course, you can also choose not to lock the screw..

The esp8266 module is 11 digital input / output pins, all pins with interrupt / PWM / I2C / support 1 line (except D0).
1 analog input(3.2V max input). Micro USB connection.
WiFi internet development board 5V 1A switching power supply (switching power supply）onboard..
5V relay shield is a digital switch to control much higher voltages and currents than esp8266 mini microcontroller, controlled by the D1 , the relay will switch to allow current to flow or turn off, depending on wiring..
40 pin 0.1inch (2.54mm) male pin header connector PCB board pin strip electronic component, they are easy to be cut to any length if needed, you can cut or score with some electronic tool..
The pin header is an ideal connector for the PCB board and intergrated circuit, used widely in the computer and breadboard, compatible with raspberry pi or other electronic project..

This is a simple and practical passive relay module, which is very convenient to use. It can support both Normally Open and Normally Close..
Input control signal: AC/DC 5V, AC/DC 12V, AC/DC24V, AC/DC48V, AC 115V, AC 230V Selectable..
Output switch DPST 1NO 1NC(Double Pole Single Throw, 1x Normally Open and 1x Normally Close ), rated current 8A/250VAC or 8A/30VDC (one switch)..
Compact ABS plastic case and wires connect for easy mount. Two screw mounting holes are convenient for you to fix it on the wall or wooden board. Of course, you can also choose not to lock the screw..