Best Xilinx Usb Jtag Cable

TX Programmer V2 for Xbox 360 Game Console, NAND for XILINX CR JTAG Programming, for Xbox 360 Mainboard Cable Repair Tools Set for CoolRunners inc, Phat and Slim, etc

Fast NAND programming and for XILINX CR JTAG programming, good performance, easy to use..
Compatible with all for CoolRunners inc, Phat and Slim, and compatible with all NAND X QSB..
Support for complete late monitoring, equipped with LED light for power and data indicator..
Easy installation system, including for KIOSK option for remote opening, built in programmer for future firmware upgrades..
Designed for J Runner application (Build 283 +), tested by professional team, reliable to use..

The USB Blaster Download Cable interfaces a USB port on a host computer to an Altera FPGA mounted on a printed circuit board..
The cable sends configuration data from the PC to a standard 10-pin header connected to the FPGA..
You can use the USB Blaster cable to iteratively download configuration data to a system during prototyping or to program data into the system during production..
It surpports most of the ALTERA FPGA/CPLD devices, Active Serial Configuration devices, Enhanced Configuration devices, and supports AS, PS, JTAG three download modes..

Intel/Altera Cyclone IV FPGA includes 6,000 Logic Elements with two clock multipliers. The Cyclone IV FPGA is the perfect balance of inexpensive cost versus plentiful logic cells, 20KBytes of SRAM, and General Purpose Input/Output pins. This is a great board to learn how to program FPGA's..
Built in programmer cable allows configuring the FPGA with a single Micro-B cable. The DPL can be powered from the USB cable or from the Barrel Connector. A separate JTAG header can also be used to program the FPGA using a compatible USB Blaster cable..
6x6 LED Array allows character and animations to be displayed at ultra fast speed. LED blocks can be individually turned on/off to allow LED signals to be used as I/O's.
70 Inputs/Outputs originating at the FPGA are available at Stackable Headers organized around the edge of the board. The user can configure these I/O's using the FPGA project code..
The DPL contains two oscillators, 66MHz and 100MHz. The 66MHz oscillator is used to provide clocking for the EPT ActiveHost USB communications core. The 100MHz oscillator can be used by the user clocked up using one of the onboard Clock-DLL modules..

Xecuter J-R Programmer v2 is an electronic module of SPI dump for NAND, optimized for J-Runner program, but also functional with AutoGG the most famous application for GLITCH RGH..
Allows dumping and fast writing of the NAND..
Also allows to program Glitch chipsets based on Xilinx chipset (glitchip and rev B and rev C).
Allows programming of NAND for 360 FAT and 360 Slim..
Allows you to programm your chip Xilinx (, X360GlitchChip ...) via a USB port with the correct timing file..

. Allows dumping and fast writing of the NAND..
. Allows programming of NAND for 360 FAT and 360 Slim..
. Allows you to programm your chip Xilinx (, X360GlitchChip ...) via a USB port with the correct timing file..
. Xecuter J-R Programmer v2 is an electronic module of SPI dump for NAND, optimized for J-Runner program, but also functional with AutoGG the most famous application for GLITCH RGH..
. Also allows to program Glitch chipsets based on Xilinx chipset (glitchip and rev B and rev C).

Zybo Z7 comes in two APSoC variants: Zybo Z7-10 features Xilinx XC7Z010-1CLG400C. Zybo Z7-20 features the larger Xilinx XC7Z020-1CLG400C. Either....
A feature-rich, ready-to-use embedded software and digital circuit development board with a rich set of multimedia and connectivity peripherals to....
Built around the Xilinx Zynq-7000 AP SoC, with 650MHz dual-core Cortex-A9 processor and DDR3 memory controller with 8 DMA channels.
On board user interfaces include 6 push buttons, 4 slide switches, 5 LEDs, 2 RGB LEDs, and more.
Expansion opportunities with six Pmod connector ports, over 30 FPGA I/O, four Analog capable 0-1.0V differential pairs to XADC, and more.

The st-link / v2 programmer is a circuit debugger and for the stm8 and STM32 microcontroller families.
The unique Wire Interface Module (Swimming) and JTAG / Serial Debugging (SWD) Interfaces are used to communicate with any STM8 or STM32....
STM8 applications use the high-speed USB interface to communicate with St Visual Developing (STVD) or St Visual Program (STVP) software..
STM32 applications use the high-speed USB interface to communicate with atollic, IAR , or Keil in integrated development environments..

The ST-LINK/V2 is an in-circuit debugger and programmer for the STM8 and STM32 microcontroller families.
The single wire interface module (SWIM) and JTAG/serial wire debugging (SWD) interfaces are used to communicate with any STM8 or STM32 microcontroller located on an application board.
STM8 applications use the USB full-speed interface to communicate with the ST Visual Develop (STVD) or ST Visual Program (STVP) software..
STM32 applications use the USB full-speed interface to communicate with Atollic, IAR, Keilor TASKING integrated development environments..