Best Wire wound Potentiometer

KST DS215MG Micro Digital Servo

100% NEW brand,high quality. Stall Torque (4.8V): 17.5oz /in (1kg/cm).
It is tiny and lightweight with high output power..
Compatible with the project like Robot Arm/ Robot hand/ control the servo with potentiometer/ multi servo control..
The SG90 has 3 wire interfaces in which the connections should be made as follows: Red wire-5V, Brown Wire-Ground, Yellow wire-digital pin 9..
SG90 9G micro servo motor for remote control helicopters, micro robot, robot arm and boats..

DUAL-CHANNEL - Connect up to 2x electric actuators with potentiometer feedback to have them travel in parallel, sequence, or individually.
SYNCHRONIZE - Connect devices with potentiometers to synchronize their movements.
SAVE UP TO 3 PRESETS - Use the wired remote to save 3x preset locations.
COMPATIBILITY - With a current rating of 15A, this control system is easy to use with a variety of 12VDC or 24VDC devices. Includes wire harness for each channel.
SPECIAL ATTENTION: Use it only with an actuator with potentiometer feedback. See at our Store PA-14P model..

Package Includes: you will get 5 potentiometers with wires (with nuts and washers) and 5 knobs, which are enough to meet your daily use and replacement needs, and you can also share them with family or friends who are in need.
Basic Information: product name: single linear rotary potentiometer.
Shaft Size: the shaft is 6 mm/ 0.2 inch in diameter and 15 mm/ 0.59 inch in length, and the mounting thread is 7 mm/ 0.3 inch in diameter.
You can rotate the shaft to adjust the resistance.
Knob Size: it is equipped with a knob for better use, and the black knob is 15 mm/ 0.6 inch deep and 17 mm/ 0.67 inch high.
The connector wire is 200 mm/ 7.8 inches long, which can be applied to connect potentiometer and power supply within a certain distance.
Wide Application: linear taper rotary potentiometer can be widely applied for photographic lenses, robotics, industrial controls, computer input devices such as trackballs, rotating radar platforms, and controlled stress rheometers.

With the compact structure and heat dissipation design, a capability of overload has been built..
[ADVANTAGE]- Metal wire is wound on the tube coated with non-flammable material, good dissipation, high stability and long life. Wire Wound Resistor owns high stability and accuracy. Moreover, it was used for various application because of the wide resistance range..
[BEST CHOICE]High precision, high power, high precision of resistance, High temperature resistance, low noise during operation, stable and reliable, can withstand high temperature and long service life..
[WIDELY - USED]- This variable wire wound resistor is widely used in power supply, transducer, elevators, arena and high requirement equipment industry. aging, load, simulation load test and inverter. Consumption of brakes, cranes, etc..

Red LED indicator will light on when moduel is power on.
Adopts 1mm dual-wire winding inductance, good filter capacitor and 8500 wiring terminals.
Please use a small screwdriver to adjust current potentiometer and voltage potentiometer.
20A fuse in the input creates dual short-circuit protection and ensures security in usage.
Over-current protection and module decreases output volt automatically if input more than 17A.

Circuit wiring set for LP SG EPI Style electric guitar, Material: Metal and wire, Switch Cap: White.
2 volume / 2 tones / 3 way switch, 2 capacitors, 1 input jack socket, prewired components make for an easy install, each tone pot has its own 2A473J capacitor, as well replace all the electronics..
2 Volume and 2 Tone Knob Pots: 2 B500k full size potentiometer, 2 A500k full size potentiometer, Pots Shaft length: approx. 18mm / 0.71", Base diameter: approx. 16mm / 0.63", Switch: Approx. 18 x 28 x 49mm / 0.71 x 1.1 x 1.9 inch.
2 tone potentiometers with the green capacitors and 2 volume potentiometer with no capacitor, pots are smooth and consistent, switch is excellent and cool that it came with a white tip.
Wiring diagram as the picture seventh shown, this harness is completely prewired. All you need to do is solder your pickups to the switch and ground them to the volume pots, more instructions please help to see the description as below. (Any other problem about product or replacement, please help to contact the seller, The way to Contact Seller: Find your order -- Contact Seller, thanks.).

✅ Top adjustment type and knurled shaft single linear 3 terminal 7 values 1K 5K 10K 20K 50K 100K 500K Ohm rotary potentiometer..
✅ Linear knurled shaft potentiometer. Shaft diameter:6mm, shaft length:17mm.
Mounting thread diameter:6mm, base size:16*7mm.
✅ Potentiometer kit offers 35pcs potentiometer knob caps. 300 degree rotary knob for easily control the potentiometer..
✅ Top adjustment type and knurled shaft for easy operate in daily use time. Stander round shaft can be push on potentiometer easily..
✅ Taper potentiometer used for volume control of audio sets, car radios, amplifiers, mixers, synthesizers and other appliances. For electronic....

This kit has all the components you need to start your projects for Arduino or Raspberry Pi and other microcontrollers.
With a precision potentiometer, better quality, power supply module and breadboard.

Potentiometer Body Size : 24 x 10mm / 0. 9″ x 0. 39″(D * H).
Potentiometer Total Height : 26mm/1. 02″.
Rotary Knob Size : 17 x 21mm/0. 67″ x0.83″(H*Max. D).
Rated Power: Linear taper B: 0.5W, Other Tapers: 0.25W.
Rotational life of the Potentiometer: 10000 Cycles, Rotational life for joystick: 100000 Cycles Min..
Package Content : 3 Pcs x Switch Carbon Potentiometer + 3 Pcs x black Aluminum alloy knob.