Best Welding Fixture Table Clamps

WYNNsky Magnetic Welding Support Ground Clamp, 2pcs Set, Single and Double Welding Head, Copper Tail

Design: This magnetic clamp attaches easily to any smooth metal surface, flat or curved. It holds on tightly, without budging easily. Super suction magnet at the bottom, large suction power, long-lasting magnetism..
Application: This device serves as the ground point, which you can take with you anywhere. Simply tack this onto a convenient spot, hook up your safety wire and you're ready to weld..
Material: The welding magnet head adopts high quality material, durable and solid. Has brass tail has good welding stability, durable, anti-rust, has good performance and long service life..
Advantage: This magnetic clamp is handy to have in such situations. You can stick in on a car body and not have to damage the paint. The clamp can also be attached to metal poles, struts, railings or the welding table..
Including 1pc Single Head Magnetic Welding Ground Clamp.
1pc Double Head Magnetic Welding Ground Clamp.
1pc Copper Tail Welding Stability Clamps..

Check Stock

ABN Butt Welding Clamps - 8 Piece Small Welding Clamps Auto Body Panel Clamps for Edge to Edge Welding

[Perfectly Align Panels] Use the ABN Welding Square Clamp Set to pinch sheet metal panels level to each other.
While these metal clamps hold panels edge to edge with a 1mm gap, you can quickly weld the sheets together.
[Fits your Project] Each welding square tool pipe clamp can extend the clamp block to provide a .4-inch (1cm) tall gap.
Fits 3/16-inch to 26 gauge sheet metal materials.
[Easy to Use] Loosen the winged nut from the alignment screw then wedge two panels across from each other between the square body and the clamp block.
Tighten the winged nut to ensure a secure hold.
Use all 8 clamps for larger projects, then joint weld between them.
[Built to Last] Panel welding clamps are constructed of zinc-plated steel to ensure maximum durability and strength while resisting rust.
[Contents] Welding accessories set includes 8 welding corner square welder clamps.
Used to make precision butt welds and edge-to-edge welds for patch repairs in floors, wings, door skins, fabricating, and re-skinning projects.

Check Stock

Toolly 16 Pack Butt Welding Clamps - Small Welding Clamps Auto Body Panel Clamps for Edge to Edge Welding

Butt Welding Clamps includes 16 welding corner square welder clamps.
Used to make precision butt welds and edge-to-edge welds for patch repairs in floors, wings, door skins, fabricating, and re-skinning projects.
Use the Toolly Welding Square Clamp Set to pinch sheet metal panels level to each other.
While these metal clamps hold panels edge to edge with a 1mm gap, you can quickly weld the sheets together.
Each welding square tool pipe clamp can extend the clamp block to provide a .4-inch (1cm) tall gap.
Fits 3/16-inch to 26 gauge sheet metal materials.
Loosen the winged nut from the alignment screw then wedge two panels across from each other between the square body and the clamp block.
Tighten the winged nut to ensure a secure hold.
Use all 16 clamps for larger projects, then joint weld between them.

Check Stock

ATPEAM Butt Welding Clamp | Pack of 16 Small Welding Clamps Auto Body Panel Clamps for Edge to Edge Welding

Premium Material: Panel welding clamps are constructed of zinc-plated steel to ensure maximum durability and strength while resisting rust.
Fits your Project: Each welding square tool pipe clamp can extend the clamp block to provide a .4-inch (1cm) tall gap.
Fits 3/16-inch to 26 gauge sheet metal materials.
Good performance: These small welding clips can be completely fixed before butt welding, leaving only a small gap to make the weld completely penetrate. This is an ideal choice for professionals engaged in sheet metal body repair..
Easy to Use: Loosen the winged nut from the alignment screw then wedge two panels across from each other between the square body and the clamp block.
Tighten the winged nut to ensure a secure hold.
Use all 16 clamps for larger projects, then joint weld between them.
Package Included: Welding accessories set includes 16 welding corner square welder clamps.
Used to make precision butt welds and edge-to-edge welds for patch repairs in floors, wings, door skins, fabricating, and re-skinning projects.

Check Stock

OBPSFY 5 PCS Magnetic Welding Clamps Set,Adjustable V-Pads Fixture Clamp Hand Tools,Magnets On Both Pad Face and Bottom

【Welding Clamp】* Hold tabs,pipe, gussets, plates and odd shaped pieces in position for tack welding.Light duty & tight spot holding! Build, Hold, and Position Steel.Magnetic tack welding Tool，make welding easier..
【Strong Hand Tools】* Adjustable welding magnet, Magnetic welding holder, hold and position round, flat, and square parts in light duty substructure applications! Time saving magnetic tools for welding..
【Material】* The magnetic welding clamps are made of high quality stainless steel, sturdy and durable, can be used for a long time.Magnets on both pad face and the bottom,Can hold the workpiece well for welding work..
【Note】* Avoid Pronlonged exposure to high heat. The Magnets may demagnetize with temp. exceeding 185°F.（Heat Warning）.
【Package】* 5 Pack Magnetic Welding Clamps（2" ，Pull Force 12 lbs.）.

Check Stock

Cylinder Pneumatic Clamp Air Clamp Hold Down Clamp with U-Bar, GH-12130 Air Toggle Clamp

METAL MATERIAL: This pneumatic clamp is made of high-strength metal material, which is anti-oxidation, wear-resistant, strong and reliable.
STABLE OPERATION: Built-in air flow control provides smoother operation during repetitive clamping operations than manual clamps.
HIGH EFFICIENCY: The pneumatic clamp can shorten test time,and improve production efficiency which reduce labor intensity of workers.
WITH U-BAR: Holding screw moves on the U-shaped hold-down bar for larger clearance angle.
WIDELY APPLICATION: The pneumatic clamp can be used in welding, fixture, mold and other positions.

Check Stock

Klutch Mobile Welding Workstation 26-Pc Metal Fit-Up Kit

4mm thick table top with fixed position steel top boards featuring 4 separate 20in. x 12in. sections.
Standard 16mm dia. holes evenly spaced 2in. apart for exceptional flexibility in fixture setup.
Firm grip handle and 4 heavy-duty 3in. swivel casters allow you to easily move the welding table where you need it, while built-in stabilizer feet....

Check Stock

5pcs/ Pack 45 Carbon Steel T Slot Nut M8/M10 Threads Black Oxide Finish for Machines Tool Tables(M8)

Made of 45 steel, black oxide finish, features high hardness, high strength, durable in use.
Undersized to fit machine table slot case hardened.
It is used for T-slot aluminum extrusions to connect other parts.
Bottom of T-Slot nut is staked to prevent the stud from protrusion.
T-Slot nuts enable the user to add clamps to a fixture without tearing down existing clamps.

Check Stock

Spurtar 6pcs Welding Magnet Welding Magnets and Clamps 75lbsX2+50lbsX2+25lbsX2 Magnetic Welding Holder 3 4 5 Arc Welding Electrode Holders 45 90 135 Degree Mig Welder Welding Accessories and Tools

STRONG POWER: 6 pieces different sizes welding magnet supports any ferrous metal object up to 25 lbs, 50 lbs, 75 lbs, satisfying all kinds of needs.
SAFE & SECURE: These welding magnets and clamps grip metal and hold it at the angle you need to work safely and efficiently. The welding holders are compact with durable high gloss enamel end plates.
THREE ANGLES: Heavy-duty arrow design steel welding magnet square supports material at 45°, 90°, and 135° for easy access. Can be used as double sided holder for welding, assembly and marking work.
MULTIPURPOSE: The magnetic welding holder clamps connects parts, freeing up your hands for efficient work and improve work safety, and it can also be used as a floater to separate steel plates.
EFFICIENCY: Spurtar Welding Magnet Set Magnetic Tool Holder s ideal welding tools and accessries for being used as holder and positioner in welding, soldering, marking off, pipe installation, making your welding job more efficiently and precisely..

Check Stock