Best Usb To Ttl Converter

USB to RJ12 6P6C RS232 FTDI Serial Converter APC PDU Cable for APC UPS 940-0144

  • Cable for programming ROPAM devices via port USB.
  • FTDI chip, Full support Windows OS, Vista, Android, Mac, Linux, Wince , etc.
  • 1.8mtr . USB to 6p6c rj12 serial converter adapter cable.
  • FTDI USB TTL Adapter Cable for Program ROPAM Devices Via Port USB MGSM.
Check Stock

DSD TECH USB to TTL Serial Adapter with FTDI FT232RL Chip Compatible with Windows 10, 8, 7 and Mac OS X

  • With this USB to TTL adapter, you can establish communication with your board/MCU through your computer. Maximum transmission speed up to 3Mbps.
  • The main chip is FT232RL from FTDI ,High stability. LED indicator for TX,RX,Power,It is very useful when you are debugging or downloading..
  • Support VCC output 3.3V and 5V, switch by jumper..
  • Works with Windows 10, 7(32/64bit) Vista 2008, XP, 2003,Mac Etc..
  • WARRANTY:We back this FDTD USB to TTL Converter with 12 months warranty.If you meet any question, Please contact us, We will fix your issue within 24 hours..
Check Stock

CP2102 6 in 1 USB to TTL Serial Adapter Module USB to TTL 485 232,TTL to 232 485,RS232 to 485 + 4P Dupont Cable Jumper Wire Female to Female for Nextion Display Beitian GPS Arduino Windows

  • -cp2102 serial adapter module supports usb to ttl, usb to rs232, usb to rs485, ttl to 232, ttl to 485, 232 to 485..
  • -USB specification 2.0 not 3.0, compatible with arduino,Windows XP/7/8/10 32bits/ 64bits, Linux etc..
  • -You need to set the dip switches for different conversion purpose..
  • -Before make 6 in 1 usb to ttl module work, you need to install cp2102 driver..
  • -cp2102 usb to ttl adapter widely used with nextion display, beitian gps, esp-01s adapter, sim7000a board etc..
Check Stock

DaFuRui 5PCS MAX3232 RS232 to TTL Converter 3.3V to 5V DB9 Female RS232 Serial Prot to TTL Converter Module Root Connector for Equipment Upgrades Like DVD

  • ★MAX3232 3.3V to 5V DB9 Male RS232 Serial Prot to TTL Converter Module..
  • ★Program the type of microcontroller: STC/STM32 / NXP / Renesas MCU / NEC..
  • ★Used in radio modification,mobile phone brushing,XBOX360 brushing machine,GPS,DVD brushing, hard disk repair,set-top box upgrade..
  • ★Package Include:5PCS x MAX3232 RS232 to TTL Serial Port Converter Module and 20pcs Dupont Lines..
Check Stock

Gowoops GPS Module with 3m Active Antenna for Arduino STM32 51 Single Chip Microcomputer

  • 1. With micro USB port, you can use general mobile phone cable to connect the GPS module to your computer. Do not need USB-TTL, convenien for use..
  • 2. The GPS module has ceramic passive antenna, you can search the satelite in a open area, do not need the external antenna..
  • 3. With SMA port, convenient for connect with the 3m Active Antenna, stronger satelite search ability..
  • 4. With the reserved TTL port, covenient for connect to USB-TTL or external single chip microcomputer..
Check Stock

Geekstory BN-880 GPS Module U8 with Flash HMC5883L Compass + GPS Active Antenna Support GPS Glonass Beidou Car Navigation for Arduino Raspberry Pi Aircraft Pixhawk APM Flight Controller

  • BN-880 is suitable for Open source flight controller, not for flight control with SCM.
  • Bn 880 gps module is dual module compass, with and electronic compass IC HMC5883L.
  • Bn 880 gps module has flash to save configuration. So you do not need to reset next time when you use it.
  • DIts data Level is TTL or RS-232, Default TTL level. To make it be RS232 output, you need to use one TTL to RS232 converter cable.
  • When you use it for Raspberry Pi, there is no driver needed but you need to install software.
Check Stock

DIYmall USB to TTL Serial Cable Adapter FTDI Chipset FT232 USB Cable TTL for Arduino ESP8266 Pack of 1pc

  • FTDI based USB to TTL Serial Cable are designed using the the standard FT232BL chipset.
  • Please note that this cable supports very low power devices-5V..
  • It can work with Raspberry Pi serial console.
  • UART interface IC device which handles all the USB signal and protocols.
  • What you will get is : 1 X USB to TTL serial cable.
Check Stock

DIYmalls BN-180 GPS Module TTL Dual Glonass GPS + GPS Passive Antenna for Arduino Raspberry Pi Pixhawk Aircraft CC3D Betaflight Flight Control

  • BN180 GPS Module can show your speed. When you use it for Raspberry Pi, there is no driver needed. Here is connection with RPi, red to 3.3v, black to....
  • When you power up bn 180 GPS module the first time in a new location, it always takes longer to find satillites. This is referred to as “cold....
  • Data Level : TTL or RS-232,Default TTL level. To make it be RS232 output, you need to use one TTL to RS232 converter cable.
  • BN 180 gps doesn't have flash and compass. If you need it, please buy bn-880 gps module via "Visit the DIYmalls Store".
  • If you have any problem, please contact seller as follow: click "DIYmalls"(you can find "Sold by DIYmalls" under Buy Now button), in the new page,....
Check Stock

Geekstory BN-220 Dual GPS Glonass Module Navigation TTL Level 9600bps + GPS Passive Antenna for Arduino Raspberry Pi Pixhawk F3 CC3D Betaflight F4 Flight Control

  • BN-220 gps module has flash to save configuration, so you do not need to reset data next time when you use it. But it has no compass. If you need gps with flash and compass, please buy bn-880 from Geekstory..
  • When you use it for Raspberry Pi, there is no driver needed but you need to install software.
  • The TX LED flash means gps module output normally.The PPS LED flash means gps module locate your place..
  • Data Level : TTL or RS-232,Default TTL level. To make it be RS232 output, you need to use one TTL to RS232 converter cable.
  • BN 220 gps module documentation link cannot be displayed. If you need technical documentation, please click “Ask a question” to em-ail us.
Check Stock