Best Usb To Serial Arduino

KEYESTUDIO Plus Board for Arduino UNO R3 with Type-C USB Cable, 3.3V 5V 1.5A Output Current, More Powerful Controller Board

  • The KEYESTUDIO Plus board can work like the Arduino Board but it is more powerful and has more pins.
  • The USB to Serial chip of this board is stable and compatible CP2102.
  • extend serial communication and I2C interface, 6 PWM and 6 analog ports.
  • special DC-DC design provides up to 5V 1.5A, can drive high-current devices like servo and motor.
  • The yellow text on black board makes identifying pinsets a breeze. FCC and CE is available.
  • How to use: Search for "keyestudio wiki KS0486" in Google Chrome to get the wiki online tutorial for this product. Technical supports are available at any time!.
Check Stock

SparkFun Qwiic Pro Micro - USB-C (ATmega32U4) - Compatible with Arduino development board 5V/16MHz microcontroller AP2112 3.3V Voltage Regulator Castellated PTH pin pads Reset button Maximum 6V input

  • Small Compatible with Arduino board. Includes Reset button, 9x 10-bit ADC pins. 12x Digital I/Os (5 are PWM capable).
  • Improved version of the SparkFun Pro Micro. ATmega32U4 running at 5V/16MHz Supported under Arduino IDE v1.0.1+.
  • On-Board USB-C connector for programming. AP2112 3.3V Voltage Regulator. PTH Pads w/ Castellated Edges.
  • Hardware Serial Connections. Includes UART (i.e. Rx and Tx), Qwiic Connector for I2C, and SPI. Has onboard Reset Button. Input maximum of 6V. Dimensions: 1.3in x 0.7in..
  • The AtMega32U4 can have the bootloader overwritten if not used properly. There is a way to fix the bootloader if needed and instructions are available online. USB drivers may be needed to be installed on a computer to communicate with the board..
Check Stock

ACEIRMC ESP32-CAM WiFi + Bluetooth Module WiFi ESP32 CAM Development Board with Camera Module OV2640 2MP + FT232RL FTDI USB to TTL Serial Converter + 20 pin Jumper Wire

  • ESP32-CAM WiFi + Bluetooth Module WiFi ESP32 CAM Development Board with Camera Module OV2640 2MPcompatible for Arduino, Support Image WiFi Upload and TF Card.
  • Bluetooth: Bluetooth 4.2 BR/EDR and BLE standard.
  • Camera WiFi + Bluetooth Module 4M PSRAM Dual-core 32-bit CPU Development Board with OV2640 2MP Camera Module + FT232RL FTDI USB to TTL Serial Converter + 20 pin Jumper Wire.
  • FTDI USB Serial Adapter comes with the FT232RL chip and uses both 3.3V and 5V operating voltage. Adapter Logic-level can be set via jumpers on the board, which makes simple to connect to your controller. USB power has over current protection, using 500MA self-restore fuse..
  • This module supports interfaces such as UART / SPI / I2C / PWM / ADC / DAC.
Check Stock

Treedix 2pcs ATmega328P CH340 Development Board Compatible with Arduino UNO R3 Board Kit for Starter

  • The board is a microcontroller board based on the CH340. It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button..
  • This is compatible board with an Atmega328p and a CH340G serial converter, 100% Compatible with Arduino UNO R3..
  • This board has the following new features: 1.0 pinout: added SDA and SCL pins that are near to the AREF pin and two other new pins placed near to the RESET pin, the IOREF that allow the shields to adapt to the voltage provided from the board. In future, shields will be compatible with both the board that uses the AVR, which operates with 5V and with the Due that operates with 3.3V. The second one is a not connected pin, that is reserved for future purposes. Stronger RESET circuit..
  • Friendly: the board is easy to use for Arduino starter, It contains everything needed to support the microcontroller.
  • simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started..
  • We strive to put our hundred percent to meet your requirements and try our best to achieve your satisfaction!.
Check Stock

Treedix ATmega328P CH340 Development Board Compatible with Arduino UNO R3 Board Kit for Starter with Cable

  • The board is a microcontroller board based on the CH340. It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button..
  • This is compatible board with an Atmega328p and a CH340G serial converter, 100% Compatible with Arduino UNO R3..
  • This board has the following new features: 1.0 pinout: added SDA and SCL pins that are near to the AREF pin and two other new pins placed near to the RESET pin, the IOREF that allow the shields to adapt to the voltage provided from the board. In future, shields will be compatible with both the board that uses the AVR, which operates with 5V and with the Due that operates with 3.3V. The second one is a not connected pin, that is reserved for future purposes. Stronger RESET circuit..
  • Friendly: the board is easy to use for Arduino starter, It contains everything needed to support the microcontroller.
  • simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started..
  • We strive to put our hundred percent to meet your requirements and try our best to achieve your satisfaction!.
Check Stock

Ingcool 4G / 3G / GNSS HAT Board for Raspberry Pi 4B/3B+/3B/2B/Zero/Zero W/Zero WH,Jetson Nano Based on SIM7600A-H 4G Support 4G Connection,LTE CAT4 for Downlink Data Transfer,

  • Compatible with Raspberry Pi 4B/3B+/3B/2B/Zero/Zero W/Zero WH,Jetson Nano,Onboard USB interface, to test AT Commands, get GPS positioning data, and so on,Onboard CP2102 USB to UART converter, for serial debugging.
  • Breakout UART control pins, to connect with host boards like Arduino/STM32,SIM card slot, supports 1.8V/3V SIM card.
  • This Product mainly applicable in North America (US, CA, MX). Supports dial-up, telephone call, SMS, MMS, mail, TCP, UDP, DTMF, HTTP, FTP, etc.Supports GPS, BeiDou, Glonass, LBS base station positioning.
  • Onboard audio jack and audio decoder for making telephone call,Onboard voltage translator, operating voltage can be configured to 3.3V or 5V via jumper,2x LED indicators, easy to monitor the working status.
  • Supports SIM application toolkit: SAT Class 3, USAT,Comes with development resources and manual (examples for Raspberry Pi/Arduino/STM32).
Check Stock

WayinTop 20x4 2004 LCD Display Module with IIC/I2C/TWI Serial Interface Adapter (Yellow Green/2004)

  • 【20x4 LCD Display】With this shield, you can display whatever you want by programming the for Arduino board. Therefore, this is a perfect choice to make your project more interesting and vivid! Totally display 20 characters in one row, 4 rows can display 80 characters..
  • 【IIC Interface Adapter】No need to buy the adapter extra, this kit contains a IIC/I2C/TWI Serial Interface Adapter, with witch you can start your project at any time..
  • 【Easy to Use】 Less I/O ports are occupied, only four - VCC, GND, SDA (serial data line), SCL (serial clock line). Address of the module: 0x27.
  • 【Support IIC Interface】It only takes two I/O port thus saving more for other usages. You can adjust the contrast by the potentiometer at its back. If you don’t want the back light, you can also unplug the jumper cap at the LCD back..
  • 【Widely Applications】LCD display module based on the popular controller, works great with for Arduino and other micro-controllers..
Check Stock

ACEIRMC 3pcs IIC I2C TWI Serial LCD 2004 20x4 Display Screen Blue + IIC I2C Module Interface Adapter for Raspberry Pi Arduino (Blue)

  • The LCD has always been a device that acts as a window in human-computer interaction. For example, the prompt window on some instrument devices, the temperature and humidity prompt box, the device running status monitor, and the prompt screen of the counting device all have LCD figures.
  • LCD2004+I2C 2004 20x4 2004A Blue/Green screen HD44780 Character LCD /w IIC/I2C Serial Interface Adapter Module for arduino.
  • It is a high-performance serial bus with bus rules and high-speed or low-speed device synchronization required for multi-master systems. The I2C bus has only two bidirectional signal lines, a serial data line (SDA) and a serial clock line (SCL)..
  • Compatible with all devices with I2C interfaces, such as for Arduino, raspberry pi, beagle bone black, tinker board, stm32, esp32 and more..
  • please check which chip you have on i2c interface. (Before you upload the code to the control board, please download the LiquidCrystal_I2C library).
Check Stock

CP2102 6 in 1 USB to TTL Serial Adapter Module USB to TTL 485 232,TTL to 232 485,RS232 to 485 + 4P Dupont Cable Jumper Wire Female to Female for Nextion Display Beitian GPS Arduino Windows

  • -cp2102 serial adapter module supports usb to ttl, usb to rs232, usb to rs485, ttl to 232, ttl to 485, 232 to 485..
  • -USB specification 2.0 not 3.0, compatible with arduino,Windows XP/7/8/10 32bits/ 64bits, Linux etc..
  • -You need to set the dip switches for different conversion purpose..
  • -Before make 6 in 1 usb to ttl module work, you need to install cp2102 driver..
  • -cp2102 usb to ttl adapter widely used with nextion display, beitian gps, esp-01s adapter, sim7000a board etc..
Check Stock