Best Transit time Ultrasonic Flowmeter

uxcell A11120300ux0019 1/2 Inch Female Thread 0.2-2.0 GPM 1-7 LPM Water Liquid Inline Flowmeter LZM-15

FLOW METER: Before use, please calibrate the flow meter with the liquid to be tested. And the flow rate of the liquid should exceed 2.5 gallons per minute, if the flow rate is too slow, the flow meter cannot measure normally. There is no battery included..
MULTI-FUNCTION DISPLAY: High-definition LCD display, can read single cumulative flow, instantaneous flow and total cumulative flow. The clear function can clear the value of cumulative flow, to make sure it is always within the measuring range. If your flow meter cannot work, please contact us in time..
HIGH-QUALITY MATERIALS: The aluminum alloy housing is sturdy, durable and corrosion-resistant, which have a long service time. The PCB circuit board make the battery have a long service life, and safe in use. Please NOTE: the LCD display is not water proof.
INSTALLATION: The flowmeter can be installed in horizontal and vertical directions, but the flow direction of the liquid needs to be consistent with the direction of the arrow on the flowmeter. There is no direction requirements for the installation of the display screen..
MEASURABLE LIQUIDS: The turbine flow meter can used for measuring the water, gasoline, diesel, kerosene, methanol and other low-corrosive, non-viscosity liquids..

【45000HZ ULTRASONIC WAVES 】This ultrasonic jewelry cleaner can generate 45000HZ ultrasonic waves to gently remove dirt and grime of your jewelry in short time. You only need to pour water in the tank, and put the items in it, a bit of liquid hand/dish soap can be added for enhanced cleaning. The ultrasonic cleaner will safely make them sparkle again..
【5 TIME MODES】This ultrasonic jewelry cleaner offers 5 different time modes, so you can freely choose the cleaning time you want with the TIME button: 90s, 180s, 280s, 380s and 480s. Even more distinctive is the【Degas mode】when you select 480 seconds. Degassing can separate the oxygen produced during cleaning by 【working intermittently】and improve the cleaning effect..
【COMFORTABLE DESIGN】 The ultrasonic cleaner with 650ML large capacity is adequate to thoroughly clean one or more items at once, saving you time and efforts. The sound below 60dB and auto shut-off design allows you to use this ultrasonic jewelry cleaner even while you sleep..
【WIDE RANGE OF APPLICATIONS】This ultrasonic cleaner can clean jewelry, glasses, watches, coins, dentures and laboratory instruments. Not only for home use, but also ideal equipment for laboratories, opticians, dentists, jewelers and watch shops..

Argon/CO2 Regulator For Welding: Zistel Argon Regulator is a ideal choice for professional TIG/MIG welding applications, which can be used to reduce and control pressure levels..
Argon Flowmeter With Pressue Gauge: Our argon flowmeter is equipped with pressure gauge, allowing you to view how much gas is left in the tank range 0 to 3500psi..
CGA580 Inlet Connection: Zistel pressure regulator is suitable for standard Argon /O2/N2 Tanks with CGA-580 Inlet Connection. You can connect the welding hose via female 5/8UNF-18RH fitting..
Hose Included: Zistel 10Ft Hose Quick Connect Fitting enable your tanks at a safe distance from your welding projects..
Field of Application: Idea choice for welding, cutting ,chemical and electronics industry.

Designed to diagnose and pinpoint common fuel system failures including failing fuel pump, faulty pressure regulator, blocked filter, pinched fuel....
Saves hours of troubleshooting time by diagnosing a bad fuel pump.
Simulates extreme driving conditions in the shop to provide the most accurate diagnosis.
Flowmeter faceplates with gal./minute and l/minute units of measure.

Argon flowmeter can be used to reduce and control pressure levels, which is a ideal tool for MIG TIG welding, chemical and electronics industry..
Inlet: CGA580, fit for argon and argon, CO2, and helium tanks..
Outlet: female 9/16" x 18 nut and male 5/8" x 18 fitting. Pressure Range: 0-3500 PSI. 1/4" Hose barb adapter is included.
The flowmeter body is made of full copper material. Fit for most kinds of welders, such as Miller, Lincoln, HTP, etc..
Output flow adjustable from 10 to 60CFH (cubic feet per hour), which is indicated by a ball which moves up and down in the flow tube..

1.VERSATILE APPLICATIONS FOR CGA-580 Tanks: This Gas Pressure Regulator/Flowmeter Can Be Used with Argon, Helium and CO2 Gas Tanks (CGA-580 Inlet).
2.Accurate Gas Flow Gague：Adjustable from 10 to 60 cfh (cubic feet per hour), and is indicated by a ball which moves up and down in the flow tube..
3.RELIABLE QUALITY - Our argon flow meter's body is made of high-quality brass, which can withstand harsh environments..
4.OUTPUT:Will fit both the female 9/16" x 18 nut or the male 5/8" x 18 fitting.It also comes with a standard 1/4" barbed fitting.
5.DESIGNED and PERFECT for MIG and TIG Welding Applications. Our Flowmeter is an economic alternative for the demanding customers who wants more precise gas metering..

40KHz Deep Cleaning: 40kHz ultrasonic frequency allows the ultrasonic jewelry cleaner to clean small items with complex construction or irregular shapes quickly.
The industrial-grade transducer creates millions of microscopic bubbles that powerfully clean your possessions while saving time.
Digital Control Panel: Working Time Setting: 0-30 minutes.
The jewelry cleaner ultrasonic machine features a digital control panel with an adjustable timer.
The LED screen is designed to show the preset working time and countdown, perfect for precise washing time control.
Premium SUS304 Material: Tank Size: 1-1.3L.
This ultrasonic cleaner machine is constructed with sturdy 304 stainless steel, ensuring no water leakage and long service life.
This commercial ultrasonic cleaner is designed for better customer use, featuring humanized details.
The dual fuse protection and multiple cooling holes are provided to avoid over-current and overheat.

200 Amp fully assembled 26V Series TIG Torch, designed for welders with Dinse or Stud Connectors or with separate TIG Module or TIG Box..
Choose between 5/16" Terminal, LC-40 cable connectors or Dinse Style Connectors, (Please check Picture #2 for dimensions and characteristics).
Available with 12.5 or 25 feet Cable and Straight or Flexible Head. Torch head with valve for a manual closure of argon flow..
2 Pieces, gas hose is separate from power cable for independent connection with welder gas outlet or directly to the argon flowmeter..
Accessory Kit and Heavy-Duty Nylon Cable Cover are Included. Other accessories might be needed to connect the argon line to your welder or flowmeter.....