Best Tank Lorry Flow Meter

Horiba 9096001700 Plastic Body PH Electrode

Modular design makes it suitable for use with output modules, sensors and remote transmitters.Compact structure, easy to install.Intuitive clear reading, high reliability, measuring accuracy is ±1%.High-definition displays show both instantaneous and cumulative flow.Can be widely used to measure diesel, kerosene, gasoline, etc..
This digital turbine flow meter has modular design, high accuracy, compact size and stable performance. Easy to replace and maintain internal components. Suitable for use with output modules, sensors and remote transmitters..
Malfunction and solution:The flow meter is not accurate. 1. The method of field calibration is not correct. Calibrate again. 2. The flow rate on the meter is below the lowest. Increase the flow rate. 3. The flow meter is blocked by the dry liquid. Take out the impeller and clean it carefully and make sure the impeller turns freely..
4. The impeller is wrapped by the sealing material. Remove the meter and make sure the impeller turns freely. 5. Too close to the impeller. Install properly 6. Too close to the motor or electronic noise environment.
The meter can not calibrate. 1. Circuit board is break down. Replace the circuit board. 2. Button is fail to press. Replace the circuit board..

Check Stock

BISupply Heating Torch with 5 Meter Hose – Portable Torch Weed Burner Propane Torch Hose

[Built to Last]: Constructed of stainless steel, these weed burners are resistant to rust and corrosion.
The torch features a steel jet nozzle and a durable adjusting valve to control the flame size and temperature.
This kit also includes a natural rubber 5-meter hose that has a 300 PSI rating and is explosion proof.
Designed for use with 20 lb. propane tanks.
[Contents]: This propane torch weed burner kit includes (1) 33.5-inch (85.1 cm) Heat Gun with turbo blast trigger handle, flow valve knob, and jet nozzle torch tip, and (1) 15-foot (5 meters) gas torch hose.
The natural rubber hose weighs 1.8 lbs. (.8 kg) and is classified as “Class 2 – 6.5mm – Propane/Butane”.

Check Stock

AFWFilters Iron Pro 2 Combination water softener iron filter Fleck 5600SXT digital metered valve 64,000 grain, 64k for whole house

Water softener, iron filter, all in one! high flow for whole house use!.
64,000 grain capacity, fine mesh resin designed for high iron removal & long life.
Fleck 5600SXT digital metered valve for efficiency and ease of use, 5 year warranty!.
Removes hardness up to 75 gpg, Iron up to 6-8 ppm range, Manganese up to 6 ppm, sediment, sand, rust.
*tank color may vary*, this comes complete with brine tank, DIY instructions, bypass valveDescriptionChoose the best for hard water and iron removal Eliminates Red Staining from iron Eliminates scale from hard water Removes Manganese Meter Based Regeneration Fleck 5600SXT Digital Control Head 1" Bypass Valve 12"x48" Structural USA Tank* Treats up to 16GPM Special fine mesh resin made to last longer in the presence of iron and filter better! Control Head - 5 year warranty Tank - 10 year warranty 30-day Satisfaction Guarantee DIY Installation Instructions Free Phone and/or email Tech Support Eliminate the hard water that causes scale build up and iron that causes red staining with a single system! Eliminates Scale Buildup - Hard water causes a white flaky build up (called scale) to form on appliances, faucets, and just about anything that it comes in regular contact with. By removing the hard water, this scale build up....

Check Stock

SONNLER Argon/CO2 Regulator Flow Meter Compatible With 6.6FT GAS Hose Welding Gas Regulator For CGA-580 Mig Tig Welder Accessories

【Premium Quality Argon Regulator】SONNLER argon flow gauge regulator made of premium durable brass, can withstand harsh environments and has a longer life, won't rust, won't leak, improve your welding skills..
【Wide Application】Ideal for CGA 580 tank fitting, this gas pressure regulator/flowmeter can be used with argon, helium, and CO2 gas tanks (CGA-580 inlet). It's compatible with Miller, Lincoln, Hobart, and most other TIG welders, apply to welding,cutting, chemical, and electronics industries..
【Accurate& easy to read】Adjustable from 0 to 60 cfh (cubic feet per hour), this argon regulator's gas flow is indicated by a ball that moves up and down in the flow tube. The easy-to-read bottle pressure gauge shows how much gas is left in the tank (range 0 to 4000psi). It fits both the female 9/16" x 18 nut or the male 5/8" x 18 fitting.It also comes with a standard 1/4" barbed fitting ..
【Two Connection Ways】You can choose the connection method according to your needs..
【7*24 after-sales service】You'll receive 1 x Argon/CO2 flow meter gas regulator, 1 x 6.6 ft hose, and a 30-day warranty. If there is a problem, please feel free to contact, we have professional engineers to provide support..

Check Stock

CGOLDENWALL Turbine Flow Meter Fuel Meter Digital Flowmeter with FNPT Thread, Flow Meter for Water Diesel Kerosene Gasoline, Flow Rate Range 2.5-26GPM (1 inch Flow Meter)

FLOW METER: Before use, please calibrate the flow meter with the liquid to be tested. And the flow rate of the liquid should exceed 2.5 gallons per minute, if the flow rate is too slow, the flow meter cannot measure normally. There is no battery included..
MULTI-FUNCTION DISPLAY: High-definition LCD display, can read single cumulative flow, instantaneous flow and total cumulative flow. The clear function can clear the value of cumulative flow, to make sure it is always within the measuring range. If your flow meter cannot work, please contact us in time..
HIGH-QUALITY MATERIALS: The aluminum alloy housing is sturdy, durable and corrosion-resistant, which have a long service time. The PCB circuit board make the battery have a long service life, and safe in use. Please NOTE: the LCD display is not water proof.
INSTALLATION: The flowmeter can be installed in horizontal and vertical directions, but the flow direction of the liquid needs to be consistent with the direction of the arrow on the flowmeter. There is no direction requirements for the installation of the display screen..
MEASURABLE LIQUIDS: The turbine flow meter can used for measuring the water, gasoline, diesel, kerosene, methanol and other low-corrosive, non-viscosity liquids..

Check Stock

Flame King Tankless Outdoor Portable Propane Gas 10L 2.64GPM Water Heater 68,000 BTU for Hot Water Shower, RV, Camping, Farm, Cabins

Fully adjustable control knobs and visual digital meter - Winter/Summer Setting, MIN/MAX Gas Setting, MAX/MIN Water Flow Rate Setting, Digital Water Temperature Meter.
Durable steel cased water heater designed to last.
On/off water control shower head and 4.5 Feet of Stainless Steel Wrapped Hose to avoid kinks and punctures..
Regulator and 4.5 ft. hose included for use with a BBQ propane tank (QCC1 Type-1 Valve.

Check Stock

HighFree Argon Regulator TIG Welder MIG Welding CO2 Flowmeter 10 to 60 CFH - 0 to 4000 psi Pressure Gauge CGA580 Inlet Connection Gas Welder Welding Regulator

▶Flowmeter which is perfect for Mig and Tig Welding. Flow Meters,it fit argon ,co2 and argon/co2 fixed. Inlet connection:CGA580..
▶ Compatiblewith a range of gases, including CO2 as well as argon, and designed to reduce and control pressure levels, this MIG/TIG Welding Argon Regulator really is a must-have for any welder..
▶For convenience, the regulator is equipped with a high pressure weld gauge that allows you to view how much gas is left in the tank, while the ergonomic flow meter can be adjusted for different uses. Applicable for many kinds of gases, such as CO2, argon, etc..
▶ It can screw right into the Argon, Argon/CO2, and Helium Tanks. The Square flow tube reads from 0 - 50 CFH and has large 1 1/2" diameter pressure gauge which reads from 0 - 4000 PSI, so you know how much is left in your tank..
▶ Package include: A Flowmeter with 6.5 foot Hose. Applicable for many kinds of gases, such as CO2, argon, etc..

Check Stock

Argon Regulator Dual Co2 Flowmeter by Manatee for TIG MIG Welder Gas and backpurge 60 SFCH - CGA 580 inlet connection and 5/8 x 18RH outlet fitting - Accurate Gas Metering Delivery System

✔ WHETHER YOU ARE a welding beginner or a seasoned professional, you will surely enjoy using the Argon Regulator Dual Flowmeter! Perfect for hooking....
✔ COMPATIBLE with a range of gases, including CO2 as well as argon, and designed to reduce and control pressure levels, this MIG TIG Welding Argon....
✔ DESIGNED and PERFECT for MIG and TIG Welding Applications. Our Flowmeter is an economic alternative for the demanding customers who wants more....
✔ HAS CGA - 580 Tank fitting so it will screw right into the Argon, Argon/CO2, and Helium Tanks. The Square flow tube reads from 0 - 60 CFH and has....
✔ Welders around the nation agree that the Argon Flow Meter Regulator is key to accurate gas meter readings..

Check Stock

CGOLDENWALL Turbine Flow Meter Digital Fuel Flowmeter with FNPT Inlet/Outlet, 1inch Flow Meter for Water Diesel Kerosene Gasoline, 2.5-26GPM /9-100LPM (1 inch)

FLOW METER: the 1 inch flow meter can read instantaneous flow rate, single cumulative flow and total cumulative flows. But it has minimum flow rate requirment, if the flow rate of the tested liquid is lower than 2.5 gal/min, the readings will be inaccurate..
TECHNICAL PARAMETERS：① diameter of water inlet: 32mm.
③ the flow speed requirenment for tested liquid: 2.5~26 gal/min.
⑥ max temp of tested liquid: 158°F/70°C.
MULTIPLE UNITS: the flow meter provide 4 meauring units for option, which are liter, gallon, pint and quart. The unit defaults to gallons, if the unit is not gallons, please refer to the user manual to change the unit to the needed one..
NOT WATER PROOF: the flow meter is not water proof, please keep the display from water during use, to avoid chip damage. We upgraded The flowmeter has been upgraded from never-sleep model to auto-sleep model, which automatically dims the screen when no liquid is flowing through it..
WIDE APPLICATION: The turbine flow meter can used for measuring the water, gasoline, diesel, kerosene, methanol and other low-corrosive, non-viscosity liquids. If there is any problem, please contact us in time..

Check Stock