Best Stepper Motor Drive

MINARIK MM23001C 0-90/0-180V-DC 1/4-2HP 5A AMP DC MOTOR DRIVE D506404

Motor Driver: 9V-42V DC power supply, H bridge bipolar constant phase flow drive. The maximum 4.0A of the eight kinds of output current..
Motor Driver: Energy-saving semi-automatic current lock function, built-in temperature protection and over current protection.The largest 32 subdivision of the 6 models are optional..
Package: TB6600 stepper motor driver + nema 17 stepper motor + mounting bracket + inner hexagon spanner + M3/M4 screws.
Strive for 100% service satisfactory, any question or problem please do not hesitate to contact us, we are always happy to help..

L298N as Main driver chip L298N, strong driving ability, strong anti-interference, low calorific value, afterflow diode protection, more stable and reliable for Arduino projects, Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability..
Double H bridge design, can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors, high efficient, To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage..
Driving DC motor Because the module is drived by double H bridge,it can drive two motors simultaneously.Input the following driving timing from IN1-IN4 then the speed and direction of the stepper motor can be controlled..
Easy to Use No assembly required. This L298N board comes ready to go. Just wire up motors and power, easy to use..
Wide Usage Great for DIY Smart Car Robot Power MEGA R3 for Mega2560 Duemilanove, if driving voltage is more than 12V, use external standard 5volt TTL outputs to switch the H-bridge circuits..

★The DRV8825 stepper motor driver carrier board TI DRV8825 micro bipolar stepper motor drive is a breakthrough..
★Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step..
★Simple step and direction control interface..

This controller board is designed for Genmitsu CNC Router 1810-PRO, 3018, and 3018-PRO. It can perfectly compatible with SainSmart Blue Laser Module..
Software: GRBL controller, UniversalGcodeSender..
Support XYZ three-axis control, spindle and laser module. Support 3 pin and 2 pin lasers (the 2 pin lasers: please connect the white interface " + s-")..
Support stepper motor: 12V, the maximum current within 2A, recommended within 1.5A and additional heat. (Any stepper motor 42, 57)..

【Functions】The function of this motion control card includes that it supports automatic probe tool, emergency input, limit switch, and supports....
【4-axis Linkage】Usb interface board supports for 4-axis linkage, you can connect four stepper motor drives or servo drives. 4 general-purpose....
【Wide Use】The maximum step-pulse frequency of motion control card is100KHz, which is very suitable for CNC Engraving, Servo Motor, Stepper Motor....
【Advantage】The motion controller needs using external 24V DC power to isolate USB and external port, and to make the system more stable. And it....
【Drive Output Interface】The 4 general-purpose isolated relay drive output interface can drive four relays for controlling the spindle starts,....

Motor drive module is ideal for use in battery-powered smart car, toy cars, robots..
Dual H-bridge motor driver, can drive two DC motors or a 4-wire two-phase stepper motor..
Supply voltage 2V -- 10V, can drive two DC motors or a 4-wire 2-phase stepper motors ,can achieve forward rotation or reverse rotation, it is possible to adjust the rotation speed..
Dual 1.5A * 2, the peak current to be 2.5A, built-in thermal protection circuit, do not be afraid motor stall burned, automatic recovery after the temperature dropped..
Use of imported original chip, built-in low on-resistance MOS switch, minimal heat, no heat sink, small size, low power consumption, is ideal for battery powered..

Package included: 1 x Stepper Motor Driver..
✿Stepper Motor Driver✿: 9V-42V DC power supply, H bridge bipolar constant phase flow drive. The maximum 4.0A of the eight kinds of output current..
✿The largest 32 subdivision of the 6 models are optional.
Suitable for 4Wires, 6 wires and 8 wires stepper motor. it can control 2 phase stepper....
✿Protect form✿: Energy-saving semi-automatic current lock function, built-in temperature protection and over current protection, under voltage....
✿Suitable for a wide range of stepping motors of Nema 17, 23 and 24 can used in various kinds of machines, such as X-Y-Z tables, labeling machines,....

Motor Driver: 9V-42V DC power supply, H bridge bipolar constant phase flow drive. The maximum 4.0A of the eight kinds of output current..
Motor Driver: Energy-saving semi-automatic current lock function, built-in temperature protection and over current protection.The largest 32....
Package: TB6600 stepper motor driver + nema 17 stepper motor + mounting bracket + inner hexagon spanner + M3/M4 screws.
Strive for 100% service satisfactory, any question or problem please do not hesitate to contact us, we are always happy to help..

【Product Structure Analysis】- Nema23 Stepper Motor+Stepper Motor Connecting Piece+Coupling+1605 Ball Scew+Slide Block+Sliding Table +Bearing....
【Nema23 Stepper Motor】- Motor length: 56mm. Motor flange size: 57mm. Holding torque: 1.2N.m. Phase: 2. Current: 3A. Resistance: 0.8 Ω.....
【1605 Ball Screw】- Drive type: CBX1605 ball screw. Effective travel length: 100mm. Screw precision grade: C7. Screw Pitch: 5mm. Flange nut screw....
【Slide Block】- Length: 60mm. M4 sliding nut design on the side, limit switch can be installed at any position. The slider is made of 6030 aluminum....
【Main Application】- The important hardware equipment that constitutes industrialized machinery can accurately control the accuracy and speed of....