Best Steel Bevel Gear

T159348 Axle Bevel Gear Aftermarket for John Deere Backhoe Sub. No. 4461351022

  • 16 teeth for use with L149Y-G mating bevel gear in 2:1 gear ratio applications.
  • Straight bevel 90 degree mesh transmits mechanical power between perpendicular shafts.
  • Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles.
  • Low carbon steel (0.2 percent carbon) for applications where the hardness and strength of higher levels of carbon are not needed to transmit torque and motion.
  • Unhardened teeth for applications where hardness and strength are not needed to transmit torque and motion.
Check Stock

uxcell® 90 Degree Shaft Angle Replacement Part Spiral Bevel Helical Gear Set 3pcs

  • Ring Gear Size: 44 x 13mm/1.73'' x 0.51''(Max.D*T).
  • Pinion Gear Size: 19 x 12.5mm/0.75'' x 0.49''(Max.D*T).
Check Stock

Keylights Key Blank Specialty Bagged Sc1 Purple Plastic Head, Yellow Light

  • Ring Gear Size: 46 x 14mm/1.8'' x 0.55''(Max.D*T).
  • Pinion Gear Size: 17 x 12mm/0.67'' x 0.47''(Max.D*T).
Check Stock

EXAUTOPONE Stainless Steel Bevel Gear Set AR44 Compatible with AR44 Heavy Duty RC Car Bevel Gear Set 30T/8T

  • 32 teeth for use with L149Y-P mating bevel gear in 2:1 gear ratio applications.
  • Straight bevel 90 degree mesh transmits mechanical power between perpendicular shafts.
  • Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles.
  • Low carbon steel (0.2 percent carbon) for applications where the hardness and strength of higher levels of carbon are not needed to transmit torque and motion.
  • Unhardened teeth for applications where hardness and strength are not needed to transmit torque and motion.
Check Stock

1PC 90-Degree reversing Angle Gear Right Angle Gear Steering Small Bevel Gear Box Bevel Gear Speed Ratio 1:1 (A)

  • 16 teeth for use with PA4416Y-G mating bevel gear in 4:1 gear ratio applications.
  • Straight bevel 90 degree mesh transmits mechanical power between perpendicular shafts.
  • Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles.
  • Low carbon steel (0.2 percent carbon) for applications where the hardness and strength of higher levels of carbon are not needed to transmit torque and motion.
  • Unhardened teeth for applications where hardness and strength are not needed to transmit torque and motion.
Check Stock

Boston Gear L153Y-G Bevel Gear, 1.5:1 Ratio, 0.750\ Bore, 10 Pitch, 30 Teeth, 20 Degree Pressure Angle, Straight Bevel, Steel

  • 30 teeth for use with L153Y-P mating bevel gear in 1.5:1 gear ratio applications.
  • Straight bevel 90 degree mesh transmits mechanical power between perpendicular shafts.
  • Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles.
  • Low carbon steel (0.2 percent carbon) for applications where the hardness and strength of higher levels of carbon are not needed to transmit torque and motion.
  • Unhardened teeth for applications where hardness and strength are not needed to transmit torque and motion.
Check Stock

Boston Gear L147Y-P Bevel Pinion Gear, 2:1 Ratio, 0.188\ Bore, 20 Pitch, 10 Teeth, 20 Degree Pressure Angle, Straight Bevel, Steel

  • 10 teeth for use with L147Y-G mating bevel gear in 2:1 gear ratio applications.
  • Straight bevel 90 degree mesh transmits mechanical power between perpendicular shafts.
  • Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles.
  • Low carbon steel (0.2 percent carbon) for applications where the hardness and strength of higher levels of carbon are not needed to transmit torque and motion.
  • Unhardened teeth for applications where hardness and strength are not needed to transmit torque and motion.
Check Stock

Makita 5377MG Magnesium 7-1/4-Inch Hypoid Saw

  • ...500 RPM with compressed winding technology to keep the overall size more compact yet deliver jobsite durability.
  • Magnesium components create a lightweight saw (13.2 lbs.) that is well balanced and jobsite tough.
  • Retractable hook allows tool to remain close by, but never in the way.
  • High quality, heat treated hypoid steel gears do not prematurely wear like traditional bronze-alloy worm drive gears.
  • Oil bath technology is created with a built-in fan and sealed gear housing to ensure 100% oil surface coating for less maintenance.
  • Make quick, one-handed adjustments using large, rubberized levers.
  • Better fit and more control with comfortable rubber grip on handle.
  • Large cutting capacity (2-3/8″” at 90°) and bevel capacity (0°-51.5°) with positive stops at 22.5°and 45°.
  • Settings are easy to read with oversized number and ruler markings.
  • Blade wrench is attached to saw for fast and convenient blade changing.
  • Large bevel capacity with positive stops at 22.5 degrees, 45 degrees, and 51.5 degrees..
  • Oil-bath technology is created with a built-in fan and sealed-gear housing to ensure 100% oil surface coating.
Check Stock

PGFUN 2 Pcs 1M 20 Teeth 5/6/8mm Shaft Hole Tapered Bevel Gear 1:1# 45 Steel 1 Module 90 Degree Steering Gear with M5 Fixing Hole (5 mm)

  • 18 teeth for use with L152BY-G mating bevel gear in 2:1 gear ratio applications.
  • Straight bevel 90 degree mesh transmits mechanical power between perpendicular shafts.
  • Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles.
  • Low carbon steel (0.2 percent carbon) for applications where the hardness and strength of higher levels of carbon are not needed to transmit torque and motion.
  • Unhardened teeth for applications where hardness and strength are not needed to transmit torque and motion.
Check Stock