Best Spin2success

3.3V 2.4 inch TFT LCD Touch Panel for Industry with PCB ILI9341 240x320 Pixels for Home

This is a new 2.8 inch serial SPI color display module with touch function, 5V compatible, use with 3.3V or 5V logic..
Support analog SPI and hardware SPI, Designed with one socket for memory card..
With PCB plate (including power supply IC, Memory Card), compatible with 5110 interface..
This kit requires professional knowledge and ability, please make sure you know how to use it..
Please note that the new type and old type of this product will be sent randomly, and make sure you will not mind before ordering..

I2C mode up to 400Khz, configurable slave address.
Two pin 3.3V UART mode, baud rates {9600, 19200, 38400, 57600, 115200}.
4-pin SPI mode, supports all 4 standard SPI modes, up to 3Mhz clock.
Backlight brightness and contrast controlled by software commands.
Source code examples for custom applications, showing how to interface with the LCD from any I2C/UART/SPI hardware.

Power supply mode:3.3V external power supply, current should be more than 200mA.
USR-ES1 is the Ethernet module of a SPI interface, interface is TTL level of 3.3V, power supply voltage of +3.3V, please ensure that the current is not less than 200mA, voltage is continuous and stable +3.3V..
W5500 SPI to LAN Ethernet Network Module TCP IP STM32 Interface 3.3V 5V for Arduino WIZ820io RC5.
Control interface:The TTL level, 3.3V SPI interface.

Compatible devices: serial connected devices, serial network/monitoring equipment, data acquisition systems, POS terminals and industrial PCs, serial I/OUSB for add-on cards, I/O expansion for embedded systems.
2S + SPI (PCIe to dual serial and SPI) and LB (PCIe to local bus/ISA)-Like) are suitable for different types of applications..
AX99100 is a single-chip solution that can fully integrate PCIe 2.0 Gen 1 endpoint controller and SerDes with various peripherals, such as two/four high-speed serial ports, one parallel port, I2C master, high-speed SPI, local Bus (ISA-Like)) and GPIO..
Composed of four main configurations, such as 2S (PCIe to Dual Serial), 2S + 1P (PCIe to dual serial and single parallel),.
Single-channel (X1) PCI Express endpoint with integrated PHY controller.

Perfect for microcontroller storage and retrieval - whether it's images, fonts, GIFs, audio files, or sensor logs.
Multi-pin data protocol (up to 4 data pins at once!).
Can be used with SDIO hardware support - clocked faster that SPI.

The Adafruit ATWINC1500 WiFi Breakout uses SPI to communicate, so with about 6 wires, you can get your wired up and ready to go. Right now the Atmel-supplied library works great with Arduino M0's and M4s but does not work on Uno (328P) and may not work on other Arduinos. You can clock it as fast as 12MHz for speedy, reliable packet streaming. And scanning/connecting to networks is very fast, a few seconds..
This module works with 802.11b, g, or n networks & supports WEP, WPA and WPA2 encryption. You can use it in Soft AP mode to create an ad-hoc network. For secure client connections, there is TLS 1.2 support in firmware 19.4.4!.
Since this is our new favoritest SPI-protocol WiFi module we've decided to make a little breakout for it. The breakout comes with level shifting on all the input pins so you can use it with 3V or 5V logic. A 3.3V voltage regulator that can handle the 300mA spikes lets you power from 3-5.5VDC..
There's also 3 LEDs that you can control over the SPI interface (part of the library code) or you can have controlled by the Arduino library. They'll light up when connected to an SSID, or transmitting data..

DSL Modem For Century Link Phone Line and Internet Service.
As part of its wireless security design, the PK5001Z supports WPA2/WPA/WEP and features a hardware WPS button allowing customers to enjoy easy setup....
Wired Transfer Rate: 10/100/1000Mbps --- Wireless Transfer Rate: 300Mbps.
Through ZyXEL’s implementation of dual Ethernet firewalls (NAT and SPI), the PK5001Z is able to identify and manage malicious content and....

a breakout board that lets you use the powerful ESP32 as a WiFi co-processor..
Having WiFi managed by a separate chip means your code is simpler,.
Send basic but powerful socket-based commands over 8MHz SPI for high speed data transfer.
We placed an ESP32 module on a PCB with level shifting circuitry, a 3.3V regulator, and a tri-state chip for MOSI so you can share the SPI bus with other devices.

Flight controller: CRAZYBEE F4 Lite Firmware target: Frsky SPI RX version is CrazybeeF4FR.
Flysky version is Crazybee F4FS. Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready. Built-in Betaflight OSD(SPI Control). Built-in 5.8G VTX. Built-in SPI Frsky/Flysky receiver. Built-in 5V 1A BEC. Built-in voltage detection..
Onboard 4in1 ESC: MCU upgraded to EFM8BB21 Power supply: 1S LiPo/LiPo HV Current: 5A continuous peak 6A (3 seconds) Support BLHeliSuite programmable Factory firmware: O_H_5_REV16_7.HEX Default protocol: DSHOT600.
Runcam Nano3: Horizontal Resolution: 800TVL Lens : 2.1mm(M8) FOV 160° Signal System: PAL/NTSC Non Switchable Day/Night: Color.
Onboard 5.8g 40-CH 25mw VTX: Input voltage: 3.3V 5.5V Current consumption: 300mA(type) Frequency: 5.8GHz 5bands 40 channels Smartaudio ready.