Best Spi Isolators

MAOPINER 4Pack Ceiling Vibration Damping Mounts, Spring Vibration Isolator for Soundproof and Shockproof for A/C Air Handler Bedroom Theater Studio, 110 Lb Capacity, 1.20\ Deflection

Premium Material: The red part of the ceiling vibration damping mounts is made of silicon instead of rubber, better functioning in absorbing vibration. And also the silicon applied is qualified, safe and environmentally friendly material..
Specification: 100mm*45mm*50mm or 4''*1.8''*2''.
Weight: 0.4kg. Material: steel & rubber. Max load: 50kg (110lbs).
The recommended distance of each two isolators is 24 inch, e.g. 63~99 isolators are needed for a room aera of 215~322 sq ft.
Easy To Install: The base of the mechanical vibration damping pads has 1 bolt hole on base for rigid mounting when used for supporting machinery, easy installation on ceilings, floors, walls, ducts, etc..
Wide Application: : The shock absorber can be used in bedroom, studios, home theaters, houses, hotels, bars, karaoke room etc. Can be mounted to ceilings, walls, pumps..
Package Included: 4 x 110 Lb capacity spring vibration isolators.

PACKAGE INCLUDED - MuHize 2Pcs black D-ring shackle isolators + 4 Pcs black washers kit. Perfect fit for standard 0.75" or 3/4" D-Rings or Shackles with 7/8" screw pin..
EASIEST DIY FOR BUMPER - The shackle isolators and washers are one of the DIY necessities of the off-road trail or everyday driving. The quality shackle isolators can both protect Wrangler or pickup bumper finishes from damage and make it look cool after DIY modification..
EASY TO INSTALL - No Screws or drilling are required. And the washers can reduce rattling noise when the vehicle is in motion..
DURABLE MATERIAL - MuHize isolator & washers are specific for durable rubber material, which can prevent shackles from crack, warp or corrode effectively..
HIGH QUALITY - Perfect bending can be matched with 3/4 inch D-ring shackle. Accurate design. It can be used as a buffer to effectively protect the bumper..

Artemis General Features: 1M Flash / 384k RAM, 48MHz / 96MHz turbo available, 6uA/MHz (operates less than 5mW at full operation), 48 GPIO - all interrupt capable, 31 PWM channels, Built in BLE radio and antenna.
Additional Artemis Features: 10 ADC channels with 14-bit precision with up to 2.67, million samples per second effective continuous, multi-slot sampling rate.
Additional Artemis Features: 2 channel differential ADC, 2 UARTs, 6 I2C buses, 6 SPI buses, 2/4/8-bit SPI bus, PDM interface, I2S Interface, Secure 'Smart Card' interface, FCC/IC/CE Certified (ID Number 2ASW8-ART3MIS).
Specific Peripherals made available on MicroMod Artemis: 1x USB dedicated for programming and debug, 1x UART with flow control, 2x I2C, 1x SPI, 1x Quad-SPI, 8x Fast GPIO, 2x Digital Pins, 2x Analog Pins, 2x PWM, 1x Differential ADC pair, Status LED, VIN Level ADC.
Additional peripherals are available but are shared on dedicated MicroMod pins. Processor board only, additional carrier board(s) will be needed to use..

Flight Controller: (Frsky SPI RX Version) CRAZYBEE F4 Lite Frsky version Firmware target: CrazybeeF4FR.
(Flysky SPI RX Version) CRAZYBEE F4 Lite Flysky version Firmware target: CrazybeeF4FS.
Receiver Option: Internal SPI Frsky Version (Compatible with ACCST D8/D16, Recommend Non EU transmitter D8 mode).
Internal SPI Flysky version(Compatible with AFHDS 8CH and AFHDS-2A 14CH Flysky transmitter).
Motor Speed Option: SE0802 KV25000(Race Edition).
Onboard 4in1 ESC : Support BLHeliSuite Programmable.
AIO 4IN1 Crazybee F4 Lite Flight Controller built-in 5.8G VTX.
Extreme Light 1S 65mm Brushless Whoop only 20g.
Runcam Nano3 The Lightest 1/3 CMOS 800TVL Camera.

This is a new 2.8 inch serial SPI color display module with touch function, 5V compatible, use with 3.3V or 5V logic..
Support analog SPI and hardware SPI, Designed with one socket for memory card..
With PCB plate (including power supply IC, Memory Card), compatible with 5110 interface..
This kit requires professional knowledge and ability, please make sure you know how to use it..
Please note that the new type and old type of this product will be sent randomly, and make sure you will not mind before ordering..

I2C mode up to 400Khz, configurable slave address.
Two pin 3.3V UART mode, baud rates {9600, 19200, 38400, 57600, 115200}.
4-pin SPI mode, supports all 4 standard SPI modes, up to 3Mhz clock.
Backlight brightness and contrast controlled by software commands.
Source code examples for custom applications, showing how to interface with the LCD from any I2C/UART/SPI hardware.

Power supply mode:3.3V external power supply, current should be more than 200mA.
USR-ES1 is the Ethernet module of a SPI interface, interface is TTL level of 3.3V, power supply voltage of +3.3V, please ensure that the current is not less than 200mA, voltage is continuous and stable +3.3V..
W5500 SPI to LAN Ethernet Network Module TCP IP STM32 Interface 3.3V 5V for Arduino WIZ820io RC5.
Control interface:The TTL level, 3.3V SPI interface.

Compatible devices: serial connected devices, serial network/monitoring equipment, data acquisition systems, POS terminals and industrial PCs, serial I/OUSB for add-on cards, I/O expansion for embedded systems.
2S + SPI (PCIe to dual serial and SPI) and LB (PCIe to local bus/ISA)-Like) are suitable for different types of applications..
AX99100 is a single-chip solution that can fully integrate PCIe 2.0 Gen 1 endpoint controller and SerDes with various peripherals, such as two/four high-speed serial ports, one parallel port, I2C master, high-speed SPI, local Bus (ISA-Like)) and GPIO..
Composed of four main configurations, such as 2S (PCIe to Dual Serial), 2S + 1P (PCIe to dual serial and single parallel),.
Single-channel (X1) PCI Express endpoint with integrated PHY controller.

Perfect for microcontroller storage and retrieval - whether it's images, fonts, GIFs, audio files, or sensor logs.
Multi-pin data protocol (up to 4 data pins at once!).
Can be used with SDIO hardware support - clocked faster that SPI.