Best Spi Interface

2.9inch E-Ink Display Module 296x128 Pixel White,Black Two-Color 3.3V/5V E-Paper Screen LCD Support Partial Refresh SPI Interface for Raspberry/Jetson Nano/Ard/Nucleo

2.9inch, 296x128 resolution, with embedded controller, communicating via SPI interface, supports partial refresh. Due to the advantages like ultra low power consumption, wide viewing angle, clear display without electricity, it is an ideal choice for applications such as shelf label, industrial instrument, and so on..
Display color: black, white. Grey level: 2. Partial refresh time: 0.3s. Full refresh time: 2s. Refresh power: 26.4mW(typ.). Standby power: 170°..
Interface: 3-wire SPI, 4-wire SPI. Outline dimension: 89.5mm × 38mm. Display size: 66.89mm × 29.05mm. Dot pitch: 0.138 × 0.138..
Onboard voltage translator, compatible with 3.3V/5V MCUs.Operating voltage: 3.3V/5V. Ultra low power consumption, basically power is only required for refreshing.No backlight, keeps displaying last content for a long time even when power down.

I2C mode up to 400Khz, configurable slave address.
Two pin 3.3V UART mode, baud rates {9600, 19200, 38400, 57600, 115200}.
4-pin SPI mode, supports all 4 standard SPI modes, up to 3Mhz clock.
Backlight brightness and contrast controlled by software commands.
Source code examples for custom applications, showing how to interface with the LCD from any I2C/UART/SPI hardware.

Card-sized High Performance Board, Rockchip RK3288 with Quad-core Cortex-A17 up to 1.6GHz, 2G RAM, 16GB eMMc flash, faster read / write speeds for the OS, applications and file storage.
4*USB2.0, 1*HDMI Out, 1*Micro USB, 1*UART, 1*GPIO interface, WiFi and 1000M LAN interface, Micro SD card (TF card : Max64G).
Multiple DIY use Single Board Computer, use the Form Factor of Raspberry Pi, DIY Friendly Design: 40 Pin GPIO header with I2S, I2C, SPI, UART, etc.
According to the definition of Raspberry Pi, which is suitable for the field of programming education for teenagers.
Compatibility and Extensibility: 40 Pin header enables hardware re-use by maintaining compatible alternate pin functions like I2S, I2C, SPI, UART, and so on.

This is an E-Ink display module, 1.54inch, 200x200 resolution, with embedded controller, communicating via SPI interface, supports partial refresh..
No backlight, keeps displaying last content for a long time even when power down.
Ultra low power consumption, basically power is only required for refreshing.
Onboard voltage translator, compatible with 3.3V/5V MCUs.
SPI interface, for connecting with controller boards like Raspberry Pi/Arduino/Nucleo, etc..
Comes with development resources and manual (examples for Raspberry Pi/Jetson Nano/Arduino/STM32).

The Adafruit ATWINC1500 WiFi Breakout uses SPI to communicate, so with about 6 wires, you can get your wired up and ready to go. Right now the Atmel-supplied library works great with Arduino M0's and M4s but does not work on Uno (328P) and may not work on other Arduinos. You can clock it as fast as 12MHz for speedy, reliable packet streaming. And scanning/connecting to networks is very fast, a few seconds..
This module works with 802.11b, g, or n networks & supports WEP, WPA and WPA2 encryption. You can use it in Soft AP mode to create an ad-hoc network. For secure client connections, there is TLS 1.2 support in firmware 19.4.4!.
Since this is our new favoritest SPI-protocol WiFi module we've decided to make a little breakout for it. The breakout comes with level shifting on all the input pins so you can use it with 3V or 5V logic. A 3.3V voltage regulator that can handle the 300mA spikes lets you power from 3-5.5VDC..
There's also 3 LEDs that you can control over the SPI interface (part of the library code) or you can have controlled by the Arduino library. They'll light up when connected to an SSID, or transmitting data..

This is an E-Ink display module, 2.9inch, 296x128 resolution, with embedded controller, communicating via SPI interface, supports partial refresh..
Due to the advantages like ultra low power consumption, wide viewing angle, clear display without electricity, it is an ideal choice for applications such as shelf label, industrial instrument, and so on..
No backlight, keeps displaying last content for a long time even when power down.Ultra low power consumption, basically power is only required for refreshing.
SPI interface, for connecting with controller boards like Raspberry Pi/Jetson Nano/Arduino/Nucleo, etc..Onboard voltage translator, compatible with 3.3V/5V MCUs.
Comes with development resources and manual (examples for Raspberry Pi/Jetson Nano/Arduino/STM32).

Brand new original ADXL345 chip, quality assurance.
According to the 16-bit two's complement format, it can be accessed through the digital interface SPI (3-wire or 4-wire) or I2C.
ADXL345 is very suitable for mobile device applications. It can be used for tilt sensing applications while measuring static acceleration of gravity,....
With high resolution (13 bits) measurement up to ±16g. The digital output data is in 16-bit two-valued complement format, which can be passed through....
Communication method: IIC / SPI communication protocol.

Size: 1.54in screen can provide clear view for you..
Drive Voltage: 3.3V-5V. The pin has good contact performance, ensure stable working.
Material: Adopted of high quality electronic components, and preciseness process, ensure for the durability.
Resolution: 128 x 64. Great workmanship, easy and convenient to install. Driver IC: SSD1309, compatible with SSD1306. Interface: SPI interface I2C interface.
Optional Style: Display White, Display Yellow, Display Blue. Available in three colors for your choice..

SPI TFT LCD Touch Panel is designed with one socket for sd card..
With PCB plate (including power supply IC, SD), compatible with 5110 interface.
5V compatible, use with 3.3V or 5V logic..
This is a new 2.8 inch serial SPI color display module with touch function..
We strive to provide a product of the highest quality and the best customer experience, if you are not completely satisfied, do not hesitate to contact us at any time..