Best Special Camera Module

DJI Part 14 Command Unit for Ronin-S Gimbal

  • The Ronin S/SC pan/tilt control module is equipped with a display screen and five-dimensional buttons. It integrates pan/tilt setting functions such as motor, working mode and control settings, and can directly use the creative functions. It is easy to set the Ronin S without a mobile device. /SC Parameters and control PTZ shooting..
  • Use the screws on the body of the pan/tilt control module to install only the Ronin-S ports on either side. After installation, turn on the Ronin-S power and the gimbal control module can work..
  • Colossal photography: Set the relevant parameters according to the camera type and select Quick Start, then set the start point and end point of the shooting, and the camera will start shooting after startup. The screen displays the number of shots and the completion progress..
  • Time-lapse photography: Set the relevant parameters according to the camera type and select quick start, and then set the start and end points of the shooting. If the shooting point is delayed, the start and end positions are the same.
  • if the shooting trajectory is delayed, the start and end positions are different. The camera will start shooting after booting up..
  • You will receive: Ronin S/SC PTZ control module*1.
Check Stock

Arducam Raspberry Pi HQ Camera for Raspberry Pi, 12.3MP IMX477 High Sensitivity CMOS with C-CS Adapter and Tripod Mount for Raspberry Pi 4 Model B, Pi 3/3B+, and Pi Zero 2W

  • High Quality Camera: Compared with Raspberry Pi Camera Module V2, this camera module offers higher resolution, up to 12.3MP. Also adopting 12.3MP IMX477 sensor for shape image, resolution 4056*3040 pixels, frame rate 30 fps@1080p, 60fps@720p, VGA90 video modes, IR Sensitivity..
  • Wide Compatibility: The IMX477 camera module is not only compatible with all models of Raspberry Pi 1, 2, 3 and 4, but also with Raspberry Pi Zero and Zero 2W, which can be easily used with a simple configuration. Note: This camera module supports the latest Raspberry Pi OS Bullseye (released on Jan 28th, 2022) and libcamera apps, not for the previous Raspberry Pi OS (Legacy) users.).
  • Easy to Setup: Only a driver away from Plug-and-Play, just use the 15-22pin FPC Cable included in the package to connect the Raspberry Pi 4B/3B and camera. If you connect with the Raspberry Pi Zero and Zero W2, the 22-22pin FPC cable is needed..
  • Package included: Come with a C-CS adapter that supports the use of C-mount and CS-mount lenses. It also includes a tripod adapter that is compatible with any tripod with standard 1/4"-20 mounting screws, this allows the camera to be secured anywhere you want..
  • Application: This Raspberry Pi HQ camera can be used to monitor 3D printer, and many other vis....
Check Stock

Arducam Raspberry Pi HQ Camera, 12.3MP IMX477 Camera Module with CS-Mount Lens, Automatic IR-Cut Switching All-Day Image, Compatible with Raspberry Pi 4 Model B, Pi 3/3B+, and Pi Zero 2W

  • Raspberry Pi HQ Camera: This camera module offers higher resolution, up to 12MP, which can deliver better image quality than 8MP. Also adopting IMX477 sensor for shape image, resolution 4056*3040 pixels, frame rate 30 fps@1080p, 60fps@720p, VGA90 video modes, IR Sensitivity..
  • IR-Cut：The camera can switch IR-CUT filter in and out automatically, supports both day and night vision. which can keep you all-day image..
  • Wide Compatibility: The IMX477 camera module is not only compatible with all models of Raspberry Pi 1, 2, 3 and 4, but also with Raspberry Pi Zero and Zero 2W, which can be easily used with a simple configuration..
  • Package included: Come with a CS-Mount lens and two cables, 300mm 15-22 pin cable for Pi 1-4 connection and 300mm 22-22 pin cable for Pi 0 and Compute Module connection. Note: This camera module supports the latest Raspberry Pi OS Bullseye (released on Jan 28th, 2022) and libcamera apps, not for the previous Raspberry Pi OS (Legacy) users.).
  • Application: This Raspberry Pi HQ camera can be used to monitor 3D printer, and many other vision applications demand IMX477 camera. It can also serve for Artificial Intelligence, like facial recognition, high-speed capturing and so on..
Check Stock

Aokin for Raspberry Pi Camera Module 5MP 1080p with OV5647 Sensor Video Camera Module for Raspberry Pi Model A/B/B+ Pi 2 Raspberry Pi 3 3B+ Pi 4 and Pi Zero/Zero W with Flex Cable

  • Compatible: camera module fit for Raspberry Pi Model A/B/B+, Pi 2B and Raspberry Pi 3B 3B+, Pi 4B, Pi Zero, Pi Zero W..
  • Ribbon flex cable: 11.81in/30cm golden camera cable specially designed for Raspberry Pi zero/zero w.
  • 5.90in/15cm and 19.68in/50cm white camera cable....
  • Specification: 5 Megapixels sensor with OV5647 webcam sensor in a fixed-focus lens.
  • the high-definition video camera is capable of 2592 x 1944 pixel....
  • Endless creativity: 15-pin MIPI camera serial interface - plugs directly into for the Raspberry Pi board.
  • The camera module size: 25mm×24mm×9mm and....
  • If you have any issues for raspberry pi version 1.3 camera module, please contact us by Amazon message, we will do our best for you..
Check Stock

ACEIRMC ESP32-CAM WiFi + Bluetooth Module WiFi ESP32 CAM Development Board with Camera Module OV2640 2MP + FT232RL FTDI USB to TTL Serial Converter + 20 pin Jumper Wire

  • ESP32-CAM WiFi + Bluetooth Module WiFi ESP32 CAM Development Board with Camera Module OV2640 2MPcompatible for Arduino, Support Image WiFi Upload and TF Card.
  • Bluetooth: Bluetooth 4.2 BR/EDR and BLE standard.
  • Camera WiFi + Bluetooth Module 4M PSRAM Dual-core 32-bit CPU Development Board with OV2640 2MP Camera Module + FT232RL FTDI USB to TTL Serial Converter + 20 pin Jumper Wire.
  • FTDI USB Serial Adapter comes with the FT232RL chip and uses both 3.3V and 5V operating voltage. Adapter Logic-level can be set via jumpers on the board, which makes simple to connect to your controller. USB power has over current protection, using 500MA self-restore fuse..
  • This module supports interfaces such as UART / SPI / I2C / PWM / ADC / DAC.
Check Stock

Aoicrie for Raspberry pi Zero Camera Module 5MP 1080p OV5647 Sensor Video Compatible with Pi Zero Ribbon Cable&FPC Cable for Raspberry Pi Model A/B/B+,Pi 2 for Raspberry Pi 3,3B+ Pi Zero/Zero W Pi 4

  • for Raspberry Pi Zero CSI Camera Module with Fixed Focus Lens Camera module for Raspberry Pi, Fully compatible for Raspberry Pi A, B, B+, 2, 3, 3B+.Pi 4.Zero Zero W and 720p The camera is supported in the latest version of Raspbian,the for Raspberry Pi's preferred operating system.Work natively with all for Raspberry Pi models for your new project or drop-in replacement..
  • High-Definition video camera, The sensor itself has a native resolution of 5 megapixel. In terms of still images, the camera is capable of 2592 x 1944 pixel static images, and also supports 1080p @ 30fps, 720p @ 60fps and 640x480p 60/90 HD video recording.Easy plug and play type capability，Can be applied to image recognition and image tracking..
  • Both cables 2 cables included between the camera connectors for the Pi Zero and Model A&B series,The module attaches to for Raspberry Pi, by way of a 15 Pin Ribbon Cable, to the dedicated 15-pin MIPI Camera Serial Interface (CSI), which was designed especially for interfacing to cameras.15CM Golden Ribben Flex Cable for Raspberry Pi Zero Zerow, model: FPC.
  • 5.90in/15cm and 19.68in/50cm white camera cable for Raspberry Pi Model A/B/B+, Pi 2 and for Raspberry Pi 4 3, 3B+, model: FFC.The C.
  • Connect the included ribbon cable to the CSI (Camer....
Check Stock

Arducam Sensor Extension Cable for Raspberry Pi Camera Module V2, 300MM/1FT Cable to Extend IMX219 Sensor for Smaller Enclosure, Narrow Space Project, Work with V2 Camera on Jetson Nano

  • Fresh Design: A fresh Arducam design to extend your camera vision on the Raspberry Pi Camera Module V2 – peel off the sensor from the connector on the camera board and put our cable in between. It does NOT support 5MP V1 cameras or any other sensors..
  • Fresh Look: Give your Raspberry Pi Camera Module V2 a fresh look by freeing the sensor from the camera board without losing the traditional flex ribbon cable extension.
  • Fresh View: Having got rid of the restrictions caused by the camera board, you can now see in a new perspective and put the camera in a smaller enclosure and narrow space, like through a small hole or a tube.
  • Fresh Option: The extension cable is compatible with Arducam IMX219 Sensor drop-in replacement modules including IMX219 autofocus and IMX219 M12 lens series. Those combinations will also work with the NVIDIA Jetson Nano.
  • Note: Please detach and re-attach the connectors gently and carefully, otherwise you might cause damage to the connection. The Raspberry Pi Camera Module V2 is NOT included..
Check Stock

Arducam Mini Raspberry Pi HQ Camera, 12MP IMX477 with Low Distortion M12 Lens, 25*24mm Camera Board Compatible with Raspberry Pi 4 Model B, Pi 3/3B+, and Pi Zero 2W

  • High Quality Camera: This camera adopts 1/2.3″ 12 Megapixel IMX477 sensor for sharp image, max. still resolution 4056 x 3040, frame rates 1080p30, 720p60 and 640 × 480p60/90..
  • Mini Sized HQ Cam: The IMX477 camera has the same size (25*24mm) and mounting holes as the Raspberry Pi v2, but with better resolution (12 megapixels compared to 8 megapixels) and sensitivity (about 50% more area per pixel for improved low-light performance) than the camera module v2..
  • More Than Ultra HD: Come with an interchangeable M12 lens with a FOV of 75°(H), low distortion, which can capture UHD images while maintaining reality. For more lens kit, you can search for the ASIN:B096V2NP2T to check it out..
  • Wide Compatibility: The IMX477 camera module is not only compatible with Raspberry Pi 1, 2, 3 and 4, but also with Raspberry Pi Zero and Zero 2W, which need a simple configuration according to the manual before use. The package comes with 1 pcs 150mm/12inch 15pin to 22pin camera cable and 80mm/3.1inch 22pin camera cable..
  • Note: This camera module supports the latest Raspberry Pi OS Bullseye (released on Jan 28th, 2022) and libcamera apps, not for the previous Raspberry Pi OS (Legacy) users.).
Check Stock

POE IP Camera POE Network Camera ModuleBlueFishcam IP Security Board Camera for DIY/Repair/Upgraded (2MP, 3 Lenses)

  • 2MP 1080P POE IP board Camera network Security camera module 2.8mm,3.6mm & 6mm fixed lenses Hidden Camera Indoor Security Surveillance Motion Detection for DIY/repair/upgrade.
  • Advanced H.265X/H.264 video compression,Super low rate,high definition quality of image.
  • Support various mobile monitoring(iPhone,Android).
  • Support POE IEEE8023af/at, And it's with additional assisted power supply. Power supply required: 12V 2A or above 2A.
  • Package content: 1 piece of POE mini IP board camera/network camera module..
Check Stock