Best Shaper Coping Sled

Rockler 422866 Router Table Box Joint Jig

  • Fence constructed from MDF with low-friction melamine coating for easy sliding.
  • Precision-machined solid brass indexing keys ensure uniform finger spacing and airtight fit.
  • Cuts 6mm (1/4 Inch), 10 mm (3/8 Inch) and 13 mm (1/2 Inch) box joints on a router table.
  • Smooth-sliding sled features long skis that keep it square to the bit.
  • Ideal for creating coping joints for small and medium boxes and frames.
Check Stock

18” Precision Steel Miter Bar Rail Runner with Adjustable Spring Loaded Plungers For DIY Table Saw Crosscut Sleds, Jigs and Fixtures to Slide in 3/4 inch by 3/8 inch Miter Slots

  • ...n the bar to mount the bar using #8 wood screws (not included)..
  • Once you mount the bars to your sled, jig or fixture you are sure to feel the difference. This is especially true when you first run the bars through your miter slots. The smooth sliding action is perfect for crosscut sleds, miter angle jigs, shop made coping sleds and a whole lot more! Using two bars (only one is included) for even more stability works exceptionally well..
  • The bar is approximately 18 inches long and will fit into miter t slots and u-shaped miter slots. Non-standard slots found on some job site style table saws and other small machinery will not accept this bar due to the non-standard slot dimensions. We recommend that you measure your miter slot before placing your order..
Check Stock

Miter T-Bar for Jigs Fixtures Sleds Router Tables and General Woodworking 48 inch MADE IN THE USA

  • ...f extruded aluminum and can be cut into sections and drilled as needed. Typical uses for the T-bar are fixtures like featherboards where the featherboard needs to be kept stationary to apply consistent pressure. The T-bar also works great for sleds and other sliding fixtures like cutoff sleds on a table saw or coping sleds on a router table..
  • When mounting the Miter T-Bar it is a good idea to keep in mind that the “T” on the bottom of the track is approx. 1/8” tall, which is just enough to clear the t-slot on most miter slots. If mounted directly to platform for a sled, the tabs may catch and prevent the sled from sliding freely. To remedy this, we recommend using washers between the mounted track and the platform to allow the sled to slide as desired..
  • The Miter T-Bar can also be mounted upside down by cutting a dado slot into your sled platform that is the same depth as the T on the Miter T-Bar. The Miter T-Bar will then act much more like a standard solid miter bar. Using this type of flush mount may work better in certain situations when compared to the traditional method..
  • When we decided to start manufacturing aluminum tracks many years ago (well over 20 years), we thought that it was very important to do our best to keep the manufactur....
Check Stock

IRWIN Tools Coping Saw Blades, Coarse, 3-pack (2014500)

  • Designed for use with your existing ProTouch coping saw.
  • Replace damaged or worn-out coping saw blades.
  • These coarse coping saw blades have a tooth count of 17 pt..
  • Use a coping saw for cutting the curved profile on crown, base or chair-rail molding.
Check Stock

FOXBC Coping Saw Blades 6-1/2 Inch, 18 Pack ( 15 TPI, 18 TPI, 24 TPI)

  • 15 TPI (6-Pack), 18TPI (6-Pack),18TPI (6-Pack).
  • Coping Saw Blade Used For Cutting Wood, Plastic, Bone, Leather, Rubber And Thin Mild Metals ..
  • 6-1/2 Coping Saw Blades fits Fret, Scroll, Jewelers and Coping Saw Blades & Frame Saw..
Check Stock

Coping Kit | 1¼ Inch by 8 Foot Sections | 8 Pieces | for use with Kayak Pools | for 12 Foot by 20 Foot Pool

  • REPLACE - This replacement vinyl coping is used to replace cracked and yellowed coping, for use with Kayak Pools manufactured between 1977 and 2002..
  • PURELY COSMETIC – This coping is just superficial as it does not actually hold up the liner..
  • SNAP INTO PLACE – The pool liner snaps into the top channel while the coping snaps onto the top channel..
  • SIZE – The Coping New Style is measured at 1¼ inches by 8 feet sections..
  • INCLUDED –This kit comes with enough 8' lengths of coping and the 4 corner caps for use with your 12' x 20' Kayak Pools..
Check Stock

Jewelry Hacksaw Handle Tool Kit, Jewelers Sawbow Saw Frame 12 Blades and Mini Bench Vise with Clamp Jewelry Making DIY Craft Tool

  • High-speed steel coping saw blades cut through most materials with ease.
  • A Flat-Bar frame and DuraSteel pins on this coping saw provide durable use.
  • This coping saw has an ergonomic ProTouch handle to give added comfort.
  • 5-1/2" frame depth and 6-1/2" blade length.
Check Stock

Collins Tool Company Coping Foot

  • Turns your jigsaw into a simple and accurate coping machine without the need for jigs and templates.
  • The Coping Foot is formed from 14 ga. plated steel. Youll wear out a couple of jig saws before you wear out your Coping Foot..
  • Fits most jig saws except for Porter-Cable, and the Bosch 1590 and 1591.
  • Will not work on Festool Carvex, get the Collins Festool Carvex Coping Foot instead.
Check Stock

FOXBC Coping Saw Blades for Metal Cutting, 6-1/2 Inch , 24TPI - 20 Pack

  • Flat wire frame for tensioning standard pin end coping saw blades.
  • Blades are 6-1/2in. long & can be used with most major common coping saws.
  • Package Coping Saw Blades - 20 Pack 24TPI.
Check Stock