Best Servo To Usb Converter Board

Gowoops MEGA 2560 PRO Board Embed CH340G/ATMEGA2560-16AU Chip with Male pin headers, Compatible for arduino Mega2560 DIY

Embed version of Mega 2560 CH340G/ATmega2560 - compatible with Arduino Mega 2560 board..
Built on the Atmel ATmega2560 microcontroller and USB-UART interface chip CH340G..
Board have compact size 38x55mm. It is good solution, to make your final project on solder proto-board..
The board used the chip CH340G as converter UART-USB..

Basic Stamp microprocessor, the board uses sensor inputs, a program, and servo outputs to operate a robot using the Parallax pBasic language.
Features include 8 sensor inputs and 5 servo outputs, all with polarized connectors as well as a built-in piezo "speaker".
Holes on side on the side of the board bolt to Merkur parts.

Package includes: you will 9 pieces of servo extension cord, 3 pieces of male JST to female JR (Futaba) cable, 3 pieces of male to 2 female Y harness, 3 pieces of male to 3 female Y harness.
Abundant quantity and diverse styles that can meet your various needs.
Appropriate sizes: the servo extension cord measures approx. 15 cm/ 5.9 inches in length, universal size for your use, the color is white, black and red.
Extensive usages: these JST male to female are compatible with Futaba and JR servo, plane and helicopter servo connection or receiver connection, also nice for remote control car, RC car and more.
Well made: JST connector is made of quality PVC material, with good insulation and flame retardant.
The interior is made of tinned copper, which has a good transmission and low resistance.
Useful function: the servo extension wire is suitable for jumping from board to board, or can be applied to control panel cable remote control unit, which is male to female.

Serial Basic Breakout Board CH340G serial signal serial ic breakout development board usb micro b connector save space diy electronics projects micro b cable jumper wires.
Base on USB converter IC CH340G, there is a wide range of operating systems . You may need to install drivers the first time you connect the chip to your computer's USB port or when there are operating system updates..
The output voltage is 3.3v by default, there is a 3.3v signal, it can also be changed to 5V, changing to 5V will cause the board to output 5V and 5V signals on the VCC pin(3 .3v to 5V by a short circuit selection).
There are two LEDs on the board connected to TX (green) and RX (yellow) for faster viewing of serial traffic.
Suitable for: Arduino Pro Mini, our GPS module, cellular module and many other devices that use serial communication.

3-Pin JR plug male to male connector servo extension lead wire cable..
There is a 3 pin JST RE connector on each end. This is a simple 3 wire cable. Ideal for jumping from board to board, or something else..
Practical range: For Airplane, Helicopter, Quad co-pterter , Multi-coater RC car servo connection or receiver connection..
Packaging quantity ：10 Pcs * 10cm JR 3pin male to male plug servo extension cables wires cords leads..

You Will Get: the package comes with 15 pieces of servo extension cables, including 5 pieces of male JST to female JR (Futaba) cable, 5 pieces of male to 2 female Y harness, 5 pieces of male to 3 female Y harness, sufficient quantities and multiple styles can satisfy your different using needs.
Proper Size: the servo connector is about 15 cm/ 5.9 inches in length, suitable size for your to use, with colors of white, black and red.
Wide Application: these JST plug splitters are compatible with Futaba and JR servo, plane and helicopter servo connection or receiver connection, also suitable for remote control car, RC car and so on, providing a lot of usages for you.
Nice Craftmanship: the JST plug connector is made of quality PVC material, which has good insulation and flame retardant, and the interior is made of tinned copper, featured a good transmission and low resistance performance, you can rest assured to use it.
Practical Function: the servo wire connector can be applied for jumping from board to board, or nice to control panel cable remote control part that is male to female.

USB car cigarette lighter socket adapter: USB Input: 5V 2A, Cigarette Lighter Socket Output: 12V 8W Max.
USB Port Power Converter: convert power from USB port to 12V car cigarette lighter socket.
Convenience: Easy to power on your car electronic equipments by extra power.
Plug and play: Easy to carry when travel. The part of PCB board is moulded by PVC which can extend its life.
Fit for Driving recorder, electronic dog, car charger and other automotive electronic equipment.

The board is a microcontroller board based on the CH340. It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button..
This is compatible board with an Atmega328p and a CH340G serial converter, 100% Compatible with Arduino UNO R3..
This board has the following new features: 1.0 pinout: added SDA and SCL pins that are near to the AREF pin and two other new pins placed near to the RESET pin, the IOREF that allow the shields to adapt to the voltage provided from the board. In future, shields will be compatible with both the board that uses the AVR, which operates with 5V and with the Due that operates with 3.3V. The second one is a not connected pin, that is reserved for future purposes. Stronger RESET circuit..
Friendly: the board is easy to use for Arduino starter, It contains everything needed to support the microcontroller.
simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started..
We strive to put our hundred percent to meet your requirements and try our best to achieve your satisfaction!.

The board is a microcontroller board based on the CH340. It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button..
This is compatible board with an Atmega328p and a CH340G serial converter, 100% Compatible with Arduino UNO R3..
This board has the following new features: 1.0 pinout: added SDA and SCL pins that are near to the AREF pin and two other new pins placed near to the RESET pin, the IOREF that allow the shields to adapt to the voltage provided from the board. In future, shields will be compatible with both the board that uses the AVR, which operates with 5V and with the Due that operates with 3.3V. The second one is a not connected pin, that is reserved for future purposes. Stronger RESET circuit..
Friendly: the board is easy to use for Arduino starter, It contains everything needed to support the microcontroller.
simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started..
We strive to put our hundred percent to meet your requirements and try our best to achieve your satisfaction!.