Best Serial Breakout Board

UMLIFE 5pcs NRF24L01+PA+LNA RF Transceiver Module with SMA Antenna 2.4 GHz 1100m + 5pcs NRF24L01 Wireless Module with Breakout Adapter On-Board 3.3V Regulator for Arduino

  • It can be wildly used to wireless remote control, somatosensory devices, RFID, NFC, smart grid, smart home, wireless audio etc..
  • 5PCS NRF24L01 8 Pin Socket Breakout Adapter Board: On-board AMS1117-3.3 chip, a simple socket breakout board which is for 8-Pin NRF24L01 wireless module.
  • 5PCS NRF24L01+PA+LNA RF Transceiver Module with SMA Antenna: Built-in 2.4Ghz antenna: available software to set the address, only received local address when output data(Provide interrupt instruction), can be directly connected to a variety of microcontrollers.
  • RF24L01+ Breakout Adapter: Small power on SMD LED indicator, On-board 3.3V voltage regulator, which accepts +5V power supply input and provides 3.3V for the attached "nRF24L01+" module..
  • The packing list includes: 5 * NRF24L01+PA+LNA Wireless Transceiver RF Transceiver Module.
Check Stock

Ximimark 5Pcs 16CH Analog Digital Multiplexer Breakout Board Module CD74HC4067 CMOS Precise Module For Arduino

  • This is a breakout board for the very handy 16-Channel Analog/Digital Multiplexer/Demultiplexer CD74HC4067. This chip is like a rotary switch - it internally routes the common pin (COM in the schematic, SIG on the board) to one of 16 channel pins (CHANxx)..
  • It works with both digital and analog signals (the voltage can’t be higher than VCC), and the connections function in either direction..
  • To control it, connect 4 digital outputs to the chip’s address select pins (S0-S3), and send it the binary address of the channel you want. This allows you to connect up to 16 sensors to your system using only 5 pins!.
  • Since the mux/demux also works with digital signals, you can use it to pipe TTL level serial data to or from multiple devices. For example, you could use it to connect the TX pins of 16 devices to one RX pin on your microcontroller. You can then select any one of those 16 devices to listen to. If you want two-way communications,you can add a second board to route your microcontroller's TX line to 16 device's RX lines. By using multiple boards, you can create similar arrangements for I2C,SPI,etc..
  • The internal switches are bidirectional, support voltages between ground and VCC, have low “on” resistance and low “off” leakage, and to prev....
Check Stock

Treedix Prototype Breakout Breadboard Adapter Expansion Board for BBC Micro:bit

  • This is a connector that fits directly to the edge contacts of a BBC micro:bit. The connector has 80 pins, but because of the different widths of the micro:bit edge contacts, some of the micro:bit contacts will map to more than one of this connector's pins. Also, the back half of the pins are not used at all..
  • The edge connector gives access to all the important pins on the bottom edge of the micro:bit. Check the datasheet for the pin spacing and orientation. This connector is best used with a custom PCB..
  • This breakout board for edge connectors allows intermediate and advanced users to connect micro:bit to breadboards and other sensors, motors, LEDs, etc..
  • We can use it in many ways, it is highly recommended to use our breakout board.
  • Through the breakout board, we broke through all 21 GPIO, power and ground pins in the form of 0.1"..
Check Stock

DORHEA 5Pcs ESP32 Development Board GPIO Breakout Board 30Pin Type-C Micro USB Dual Interface ESP32 Shield 30P Ultra-Low Power Dual Core ESP32-DevKitC-32 ESP-WROOM-32 ESP-32 ESP-32S Expansion Board

  • ESP32 shield 30P expansion board, supports two power supply : DC 6.5-16v and USB 5V.
  • The GVS output power supply can be 5V or 3.3V, which is more convenient to match the external 5V electronic module sensor..
  • The breakout board is only fit for 30PIN ESP32. Please confirm your esp32 board pins width is coincide with the pin width of the breakout board.
  • ESP32 breakout board GPIO 1 into 2 only can compatible with 30 pins ESP32S ESP32 , just for ref asin: B086MJGFVV B086MLNH7N B086MGH7JV.
  • This module is safe, reliable, and scalable to a variety of applications. Stable and highly reliable.Great contact and stable signal transmission for your esp32 board.
Check Stock

Opto 22 G4PB8 G4 8 Channel I/O Module Rack

  • Screw Terminal Block Breakout Board for Arduino MKR..
  • With the breakout board, you can easily extend Arduino MKR projects to industrial control applications..
  • PCB mount Terminal Block: pitch 5.0mm/0.197.
Check Stock

Electronics-Salon DIN Rail Mount Screw Terminal Block Adapter Module, for Arduino UNO R3.

  • DIN Rail Mount Screw Terminal Block Breakout Board for Arduino MKR. With the breakout board, you can easily extend Arduino MKR projects to industrial control applications..
  • PCB mount Terminal Block: pitch 5.0mm/0.197.
Check Stock

3-Pack ESP8266 Development Board, Aideepen ESP8266 Breakout Board GPIO 1 into 2 for ESP8266 ESP-12E NODEMCU V2

  • 【ESP8266 ESP-12E】This esp8266 breakout board can fully compatible with ESP8266 ESP-12E..
  • 【Expansion Board】This expansion board can expand one GPIO pin of ESP8266 development board to two, which is convenient for users to reuse all pins in smart home projects. Nice breadboard alternative..
  • 【Ease to Use】Needn't welding components.These boards fit your ESP8266 ESP-12E perfectly,can be inserted into the sockets with minor effort by hand..
  • 【Good quality】This ESP8266 Breakout Board is design with double-layer that One pin is wired on both sides. Great contact and stable signal transmission to your ESP8266 board..
  • 【Why choose us】Aideepen specializes in various electronic components,We have always cared about the customer experience and improve the product function details,please feel free to contact us..
Check Stock

S-Union Ethereum ETH ZEC Mining Power Supply 12V GPU/PSU Breakout Board + 12pcs 16AWG PCI-E 6Pin to 6+2Pin Cables 27.5Inch Length 70CM with 5 Nylon Cable Ties

  • 【Item】GPU Mining Power Supply Breakout Board and PCI-E 6Pin to 6+2Pin (Male to Male) cable.
  • 【Performance】Measured maximum can support to 1600W power supply, 12 groups of graphics card 6pin output.
  • 【Safety】The Breakout Board have Solid state capacitor filter, suitable for a variety of server power supply. The line is 16 AWG wire，Able to....
  • 【Compatibility】This item is Compatible with GPU Mining Power Supply -HP 1200W/750W PSU. Such as DPS-1200FB DPS-1200QB PS-2751-5Q HSTSN-PL12....
  • 【What You Get And Shipping】1x Power Supply Unit Breakout Board & 12x PCI-E 6Pin to 6+2Pin Cables & 5x Nylon Cable Ties. SHIPPED FROM THE U.S.....
Check Stock

GeeekPi Raspberry Pi Pico Breakout HAT Board, Raspberry Pi GPIO Expansion Board Breakout HAT Module for Raspberry Pi Pico, Support Raspberry Pi HAT Board with 40Pin Pin Header

  • Application: This breakout HAT board, which is specially customized for Raspberry Pi Pico..
  • Convenient: Solve the problem that the Raspberry Pi Pico silk screen is covered, and providing pin header pins, which is convenient for users to build their own DIY circuits..
  • Features: Support Raspberry Pi HAT board with 40Pin Pin Header.
  • For example: GeeekPi DockerPi series HAT board, 4-channel relay HAT board, SensorHub board, etc. It Provides a good bearing platform.
  • Package Includes: 1 x Breakout HAT Board For Raspberry Pi Pico.
Check Stock