Best Rms 5 10 20

Rockville Pair RKL65MBW 6.5" 700W Marine Boat Speakers W/Led+Black/White Grilles

  • Package Includes: (2) Pair RockvilIe RKL65MBW 6.5" 700w Marine Boat Speakers w/LED+Black/White Grilles, (1) RockvilIe MS10LW 10" 2400 Watt White Marine/Boat 10" Free Air Subwoofer with LED, (1) RockvilIe DBM50 4000 Watt/980w RMS 5 Channel Marine/Boat Amplifier Amp+Mic, (1) RockvilIe RMWK4 4 AWG Gauge Waterproof Marine Amplifier/Amp Install Wire Kit,(2) RockvilIe MRCA25 25 Foot Twisted Pair Marine RCA Cable , Split Pin.
  • Features of RKL65MBW: CEA Compliant Power Ratings, Power Rating: 350 Watts Peak /85 Watts RMS Per Speaker, Total Power: 700 Watts, Beat sync LED’s flash to the rhythm of the music, You can select either red or blue color LED’s on the wire harness, No extra installation for the LED. It gets a power signal through your speaker wire, The louder the music the more intense the LED’s flash, Black and White detachable Grills, Fully Marinized Against Salt & Fresh Water Conditions.
  • Features of MS10LW: Free air subwoofer does not require any enclosure, Max Power: 2400 Watts, RMS Power: 600 Watts, Polypropylene cone with Rubber edge, 2.0" 4 Layer dual voice coil, Molded ABS plastic basket made with a special blend that is waterproof....
Check Stock

Diamond Audio MICRO4V2 4-Channel 600 Watts RMS Class D Amplifier

  • ...switch (2 CH / 4 CH) | Selectable auto-turn-on mode: Signal Sensing (VOX), 12V Remote (REM) and DC offset (DC) | Fully variable, 12dB per octave, electronic crossovers | Built-in BTR Port (MICRO-USB) to connect our optional Bluetooth receiver-controller | Illuminated logo.
  • RMS Power Rating - RMS Power (2Ω): 150W x 4 | RMS Power (4Ω): 80W x 4 | Bridged (mono 1Ω): N/A | Bridged (mono 2Ω): N/A | Bridged (mono 4Ω): 300W x 2 | Topology: Full Range Class D Power Supply | Power Supply: Full PWM | Power Supply Threshold: 10.0VDC - 17.0VDC | Idle Current: (0.7A).
  • Distortion - THD 4 (1KHx @ 4Ω): 0.5% | S/N Ratio (A weighted @1W): -85dBA | S/N Ratio (A weighted @FP): -101.1dBA | Input Sensitivity - Low Input Level: 200mV - 10.0V | High Input Level: N/A | Input Impedance - Low Input Level: 20KΩ | High Input Level: 20KΩ.
  • Output Stage - Output Impedance: 0.018Ω | Damping Factor ([email protected]Ω): >70 | Bandwidth (-3dB): 10Hz - 35Hz | Crossover (-12dB/Oct) | Variable High-Pass: 40Hz - 400Hz | Variable Low-Pass: 40Hz - 400Hz | Variable Sun-Sonic: N/A | Fuse Ratings: 40A | Dimensions: 9.07” L x 4.0” W x 1.46” H.
Check Stock

MUSYSIC MU-D16K Professional 2-Channel 2x8000 Watts D-Class 1.5U Power Amplifier

  • 2-Channel Professional D-Class Power Amplifier 2x8000 Watts Peak Output.
  • Stereo Output Power: "2x8000W PEAK, 2x4000W Program, 2x2000W RMS @ 2Ω" "2x4000W PEAK, 2x2000W Program, 2x1000W RMS @ 4Ω" "2x2000W PEAK, 2x1000W Program, 2x500W RMS @ 8Ω" / Bridge Output Power: "8000W PEAK, 4000W Program, 2000W RMS @ 4Ω" "4000W PEAK, 2000W Program, 1000W RMS @ 8Ω".
  • Frequency Response: 20Hz-20KHz,+0,-1dB at watts / THD+N(20Hz-20KHz) ＜0.23％20Hz-20KHz / Siew Rate ＞30V/us / Damping Factor ＞150 / Output Circuitry Class AB / Signai to Noise Ratio ≥96dB / Cross Talk ＞80dB / lnput Sensitivity(8Ω) 1V / input lmpedance 20 k Ω baiance / 10 k Ω unbalanced unbalance balancing 20 k / 20 k /.
  • Three cooling fans / Connectors Input: XLR input, 1/4" input: Speakon connector Output: Speakon, locking type socket, Power Requirements: 90v-250v 50Hz.
  • Controls Panel: the power switch, channel 1 and channel 2 channel gain control.
  • After the board: working mode, pressure limit./ lndicators Panel: the power switch, channel 1 and channel 2 channel gain control.
  • After the board: working mode, pressure limit./ Amplifier Protection With short circuit, overload, overheat, cut peak pressure limit, dc, soft start, relay zero current switch, super audio and radio frequency protecti....
Check Stock

MUSYSIC MU-D9600 Professional 4-Channels 2x9600 Watts D-Class 1U Power Amplifier

  • 4-Channels Professional D-Class Power Amplifier 2x9600 Watts Peak Output.
  • Stereo Output Power: "4x4800W PEAK, 4x2400W Program, 4x1200W RMS @ 2Ω" "4x2400W PEAK, 4x1200W Program, 4x600W RMS @ 4Ω" "4x1200W PEAK, 4x600W Program, 4x300W RMS @ 8Ω" / Bridge Output Power: "2x4800W PEAK, 2x2400W Program, 2x1200W RMS @ 4Ω" "2x2400W PEAK, 2x1200W Program, 2x600W RMS @ 8Ω".
  • Frequency Response: 20Hz-20KHz,+0,-1dB at watts / THD+N(20Hz-20KHz) ＜0.23％20Hz-20KHz / Siew Rate ＞30V/us / Damping Factor ＞150 / Output Circuitry Class AB / Signai to Noise Ratio ≥96dB / Cross Talk ＞80dB / lnput Sensitivity(8Ω) 1V / input lmpedance 20 k Ω baiance / 10 k Ω unbalanced unbalance balancing 20 k / 20 k /.
  • Three cooling fans / Connectors Input: XLR input, 1/4" input: Speakon connector Output: Speakon, locking type socket, Power Requirements: 115v-230v 50/60 hz.
  • Controls Panel: the power switch, channel 1 and channel 2 channel gain control.
  • After the board: working mode, pressure limit./ lndicators Panel: the power switch, channel 1 and channel 2 channel gain control.
  • After the board: working mode, pressure limit./ Amplifier Protection With short circuit, overload, overheat, cut peak pressure limit, dc, soft start, relay zero current switch, super audio and radio fre....
Check Stock

MTX (2) S6510-44 10" 1000w RMS Subwoofers+Vented Sub Box+Mono Amplifier+Amp Kit

  • Package Includes: (2) MTX 10" Subwoofer Car Audio (1) Rockville KRYPTON-M3 4000w Peak/1000w Dyno-Certified RMS Mono 1 Ohm Car Amplifier Amp+Remote (1) Rockville RWK4CU 4 AWG Gauge 100% Copper Complete Amp Installation Wire Kit OFC (1) Rockville Dual 10” Solo Baric L7/L5/L3 Vented Square Sub Enclosure Box 20 Drywall Wood Screws (Wood screws are the type of screws.
  • the screws are actually made of metal) 20 Feet of 14 AWG Blue Speaker Wire 4 Spade Terminals.
  • Features of S6510-44: MTX S6510-44 10" 1000 Watt Peak/500 Watt RMS Square 4-Ohm Car Subwoofer, RMS Power Handling: 500 Watts, Peak Power Handling: 1000 Watts, Recommended Amp Power: 250-500 Watts RMS, Impedance: Dual 4-Ohms, Frequency Response: 26Hz - 130Hz, Sensitivity: 84.5 dB, Volume Displacement: 45.65 cu in, Voice Coil: 2" inches, Mounting Depth: 6.625" inches Cut Out Diameter: 9.313" inches.
  • Features of RDVK10 : Rockville RDVK10 Dual Square 10" 1.2 Cu. Ft. Vented Subwoofer Enclosure. Designed Specifically For The Solo Baric L7/L5/L3 Series Subwoofers and Similar, Proudly Made In The USA, Using Only The Finest Quality Materials - For The Best Level of Performance From Your Subs!....
Check Stock

Memphis Audio VIV900.5 75W x 4 + 500W x 1 Car Amplifier

  • Features: 5-channel car amplifier, 50 watts RMS x 4 + 300 watts RMS x 1 at 4 ohms / 100 watts RMS x 4 + 500 watts RMS x 1 at 2 ohms / 150 watts RMS x 2 bridged at 4 ohms + 500 watts RMS x 1 at 2 ohms, Class D amp technology.
  • Tuning Controls: front channels: Variable high- or low pass filter (10-5,000 Hz, 24 dB/octave).
  • Rear channels: Variable high-pass filter (10-500 Hz, 24 dB/octave) / Variable low-pass filter (50-5,000 Hz, 24 dB/octave) / Bandpass filter engages both.
  • Subwoofer channel: Variable subsonic filter (10-80 Hz, 24 dB/octave) / Variable low-pass filter (50-500 Hz, 24 dB/octave) / Variable bass boost (0-18 dB at 45 Hz).
  • Other Features: Optional wireless remote subwoofer level control available, Preamp inputs, Speaker-level inputs (require speaker wire to RCA adapters), Hinged magnetic cover plate conceals top-mounted controls, 7 color selectable LED logo, 4-gauge power and ground leads and a 80-amp fuse recommended — wiring and hardware not included with amplifier, No onboard fuses — when installing multiple amps in a system, an additional 80-amp in-line Fuse between the distribution block and this amplifier is.
Check Stock

KICKER Pair 42PSC654 PSC65 6.5" 240 Watt Motorcycle/ATV/UTV/RZR Marine Speakers

  • Features: Pair Kicker 40PSC654 PSC65 6.5" 240w Motorcycle/ATV/Marine Speakers. Woofer: 6-1/2 in..
  • Power Handling Per Speaker: .120 Watts Peak .60 Watts RMS. Recommended power range: 10 - 60 watts RMS per channel. Fit Harley-Davidson and Victory motorcycles.
  • 3/4" Neo-titanium bridge-mounted Dome tweeters. Neodymium Magnet. Sensitivity: 92.5 (dB 1w/1m). Frequency Response: 40 Hz - 20 kHz. Mounting Depth: 2 in..
Check Stock

MTX TNP212D2 12-Inch 400-Watt RMS Dual Loaded 1200-Watt Car Subwoofer Enclosure Audio with Sub Box Mono Block Amplifier and 8 Gauge Amplifier Amp Complete Wiring Installation Kit

  • ADD BASS: Add some bass to your car with the MTX 2 x 12 subwoofer Party Pack.
  • The enclosure designs delivers bass that exceeds expectation.
  • Each subwoofer can handle 200-watts RMS power (400-watts RMS for entire enclosure).
  • HIGH QUAILITY: Enclosure is constructed with extra strength 5/8 inch medium density fiberboard to ensure the enclosure contains low frequency sound waves generated by subwoofer without problem.
  • MONO BLOCK AMPLIFIER: Includes a 250-watt mono block amplifier that easily connects to any source, including factory radios.
  • AMPLIFIER INSTALLATION KIT: Features a 20 foot 8 gauge red power cable, competition high quality fuse holder, 3 feet of 8 gauge black ground cable, 16 feet of 18 gauge blue turn on wire, a 20 foot high performance RCA interconnect, 30 feet of speaker wire, 20, 4 inch wire ties, 3, rubber grommets, a Number 10 ring terminal, a 5/16 inch ring terminal, and a 1/4 inch ring terminal.
  • SPECIFICATIONS: Subwoofer enclosure: Max power: 1200 watt.
  • Single 4 ohm voice coils per sub (pre wired down to 2 ohm load).
  • Dimensions (HxWxD) : 13.875 x 29.625 x 13.875 inches.
Check Stock

MTX TNP212D2 12' 400W RMS Dual Loaded 1200W Car Subwoofer Enclosure Audio with Sub Box, Mono Block Amplifier, 8 Gauge Amplifier Amp Complete Wiring Installation Kit and Hi/Low Converter

  • ADD BASS: Add some bass to your car with the MTX 2 x 12 subwoofer Party Pack.
  • The enclosure designs delivers bass that exceeds expectation.
  • Each subwoofer can handle 200-watts RMS power (400-watts RMS for entire enclosure).
  • HIGH QUAILITY: Enclosure is constructed with extra strength 5/8 inch medium density fiberboard to ensure the enclosure contains low frequency sound waves generated by subwoofer without problem.
  • MONO BLOCK AMPLIFIER: Includes a 250-watt mono block amplifier that easily connects to any source, including factory radios.
  • AMPLIFIER INSTALLATION KIT & CONVERTER: Features a 20 foot 8 gauge red power cable, competition high quality fuse holder, 3 feet of 8 gauge black ground cable, 16 feet of 18 gauge blue turn on wire, a 20 foot high performance RCA interconnect, 30 feet of speaker wire, 20, 4 inch wire ties, 3, rubber grommets, a Number 10 ring terminal, a 5/16 inch ring terminal, and a 1/4 inch ring terminal.
  • Converter: Hi/Low Impedance Adapter, RCA Input Sensitivity Adjustment Control.
  • SPECIFICATIONS: Subwoofer enclosure: Max power: 1200 watt.
  • Single 4 ohm voice coils per sub (pre wired down to 2 ohm load).
  • Dimensions (HxWxD) : 13.875 x 29.625 x 1....
Check Stock