Best Rebar Tying Machine

VEVOR Hydraulic Rebar Bender 1700 Wattage Electric Rebar Bender and Cutter, 1''/25 mm Max Rebar Diameter, Rebar Steel Bender and Cutter Machine, Bending Machine For Bending Rebar, Steel Bar, Steel Rod

Ultra-Fast Working Speed: This rebar bender and cutter machine is designed with excellent performance. It helps save valuable person-hours by bending rebar 1/4'' #2 to 1" #8 Grade 60(6 to 25 mm) within 6 to 7 seconds. It can also cut rebar within 5-6 seconds. Bending Angle: 0-180°. Bending Radius: 1.57'' / 40 mm, Max. Rebar Hardness: HRC30, Hydraulic Oil Type: VG46..
1700W Pure Copper Coil Motor: This rebar cutter and bender features a 1700W pure copper motor, which can run quietly with low noise and significantly improve your working efficiency, reducing unnecessary wear. Besides, a copper motor can extend this rebar bender cutter's operating life to a large extent. Voltage: 110V, Frequency: 60 Hz, Amps: 14A, Noise: 92 dB(A)..
Angle Adjustment Knobs: This rod bending machine has two slide-type angle selectors, which can help you accurately bend any angle from 0-180 degrees. Preset angle locks are designed for repeating the same angle bending. When bending processing, the angle of point 1 must be bigger than point 2. Otherwise, the machine can not operate normally..
Sturdy Machine Body: The bar bender machine adopts a sturdy iron machine body and durable Idler Wheel. Ø78 iron Gyre Idler Wheel and Ø94 Fixed Idler Wheel are stronger and not easy t....

Check Stock

LTM CONCRETE Snap Rebar Chairs 2 inch (30 Pack) – Quick, Easy & Durable Support – Bar Sizes 3-5 - Heavy Duty Plastic Spacers - Made in USA

HEAVY DUTY: LTM Snap Rebar Chairs are built with a special blend of materials that support heavy loads and strengthen your pour. Our chairs will never rust, corrode or degrade inside the concrete..
VERSATILE: Our easy-to-use clips firmly hold bar sizes #3-5.
post-tension cables, smaller bars and mesh will easily rest inside them too..
EASY TO USE: LTM Snap Rebar Chairs are already inexpensive, but you’ll save even more in labor costs. Set an entire rebar grid in minutes and skip wire-tying altogether..
MADE IN USA: The entire LTM Concrete product line is made in the USA, including 100% of our raw materials. Buy LTM and keep America working..
***NOTE: These chairs are built specifically to work in forms and on hard-packed surfaces. Their minimal footprint will sink if used on sand and other soft-earth applications..

Check Stock

LTM CONCRETE Snap Rebar Chairs 1.5 inch (30 Pack) – Quick, Easy & Durable Support – Bar Sizes 3-5 - Heavy Duty Plastic Spacers - Made in USA

HEAVY DUTY: LTM Snap Rebar Chairs are built with a special blend of materials that support heavy loads and strengthen your pour. Our chairs will never rust, corrode or degrade inside the concrete..
VERSATILE: Our easy-to-use clips firmly hold bar sizes #3-5.
smaller bars and mesh will easily rest inside them too..
EASY TO USE: LTM Snap Rebar Chairs are already inexpensive, but you’ll save even more in labor costs. Set an entire rebar grid in minutes and skip wire-tying altogether..
MADE IN USA: The entire LTM Concrete product line is made in the USA, including 100% of our raw materials. Buy LTM and keep America working..
NOTE: These chairs are built specifically to work in forms and on hard-packed surfaces. Their minimal footprint will sink if used on sand and other soft-earth applications..

Check Stock

Mophorn Rebar Tie Wire Coil 10 Rolls, Rebar Tie Tool 0.8mm Diameter, Rebar Tying Wire 110m Length, Rebar Wire for Automatic Rebar Tying Machine Supplies

Dedicated Device: It is suitable for various brands of rebar tiers on the current market, and ensures efficient performance without wire being jammed.
Premium Material: This rebar wire is made of high-quality low carbon steel. Through an elaborate process of drawing molding, acid pickling, high-temperature annealing, hot galvanizing, and cooling, the coated zinc layer is thick and corrosion-resistant..
Sustainable Lifecycle: The reusable wire spool is thickened and reinforced, which is not easy to crack the coil, and avoids the problem of getting rebar wire entangled.
the high-strength axle is uneasy to be damaged and has a longer service life..
Easy to Use: With good toughness and elasticity, it does not crack after repeated bending, which is easy to be shaped.
the wire coil is firmly bound, light in weight, convenient for transportation, and does not occupy space.
the rebar wire is finely polished with advanced technology, and the burr-free surface does not hurt hands..
Wide Application: Whenever you're thinking of tying wire, you will find it set a must-have for your work with various features. It is best for woven wire mesh, handicrafts, gardening, product ....

Check Stock

Crescent H.K. Porter Rebar Cutter and Bender - 0590RBJN

Pure Copper Motor: A pure copper motor ensures higher reliability and excellent motivation yet low noise. Moreover, it is more durable with less power consumption and low noise to extend the service life..
Excellent Performance: This portable rebar bender bending rebar up to 5/8'' (#5) grade 60 from 0-130 degrees within 5 seconds. It satisfies your various bending demand and raises your working efficiency significantly..
Solid Machine Body: Study and durable machine body and head can stand super-hard rebar with strong clamping force, which can help to reduce the waste of steel rebar. Multiple screws fixed on the head enforce the security..
Detachable Positioning Bolt: The Rebar Bender with adjustable positioning bolt allows you to accurately bend any angle within 0-130 degrees, preset angle for repeating the same angle bend..
Humanized Design: This portable automatic rebar bender features an ergonomic back grip design with two handles that facilitate maneuverability, ease of use, and security. Simply Keeping the switch pressed, the bending block starts to push forward..

Check Stock

CCTI Rebar Tie Wire - 16 Gauge Black Soft Annealed 3.5 lb. Roll (Approx 340 Ft) - 1 Pack

Premium Quality - Soft Annealed Rebar Tie Wire.
Roll Dimension: OD 4.6" - Width 5.5" - Round Hole 1.9".

Check Stock

Huanyu Electric Rebar Bender 900W Hydraulic Rebar Bending Machine 5/8Inch #5 16mm Rebar within 5s Bending Angle 0°-130° with Positioning Bolt Fast Easy Bending Rebar Steel Bar Steel Rod 110V RB-16

【Powerful 900W Pure Copper Motor】Huanyu Electric Rebar Bender adopts 900W pure copper motor with strong power. It can bend 5/8inch (#5 16mm) rebar 0-130° within 5s. Low noise and low failure rate when running. Longer service life..
【Solid Machine Body】Huanyu Rebar Bending Machine adopts sturdy cast iron body and high-strength bend block, stronger clamping force for excellent bending of rebar. Multiple screws fixed on the head enhance the safety and stability of the rebar bender..
【Easy to Operate】One button operation. Keep the switch pressed and the bending block starts to push forward. Huanyu Steel Bender is equipped with an adjustable positioning bolt. You can mark on it to control the rebar bending angle. After the rebar is bent, pull the relief valve and piston returns to its original position..
【Humanized Design】Ergonomically designed rear handle and side handle (detachable) for comfortable grip and easy operation. Integral workbench base design. You can lay the bender on a flat surface to operate. Stable and effortless. Save your back!.
【Excellent Service】NOTE: We support customized service of 220V voltage to meet your needs.1 year warranty on all products in our store. For damaged parts, we will resend a new one free of charge....

Check Stock

LTM CONCRETE Dually Rebar Chairs (12 Pack) – 7 Heights in 1 Chair - Quick, Easy & Versatile Support – Vertical & Horizontal Applications – Made in USA

EXTREME VERSATILITY: The patented Dually is the only rebar spacer of its kind – one chair holding bars at many different heights! Clips will firmly hold #3-6 bars at 1”, 1 ½”, 2”, 2 ¼”, 2 ½”, 3”. Turned on its side, Dually will support any resting mesh or bar at 2 inches (up to #12)..
WIDE BASE: Works on grade, Dually features a wide base that prevents sinking and tipping on soft surfaces. It also includes plenty of flow-through spacing for aggregate and concrete..
HEAVY DUTY: This chair is made with a special blend of materials that support heavy loads and strengthen your pour. Our chairs will never rust, corrode or degrade inside the concrete..
EASY TO USE: Set an entire rebar grid in just minutes and eliminate the need for wire-tying. Dually is already low-priced, but you’ll save even more in labor costs..
MADE IN USA: The entire LTM Concrete product line is made in the USA, including 100% of our raw materials. Buy LTM and keep America working..

Check Stock

Happybuy Hydraulic Rebar Cutter 1/4' - 7/8' / 4 mm - 22mm,Concrete Construction Tool 13Ton,Handheld Rebar Cutter G-22 w/Box,Steel Bolt Chain Cutting tool

...ing technology and strict quality control. And multiple screw fixed heads can offer quick and accurate cutting while providing double stability and sealability..
Adjustable Bolt Design: This hydraulic cutter comes with an adjustable bolt-on to make it convenient when cutting rebar of various sizes. The rebar cutting machine we designed has low noise and a low failure rate, which is very helpful for work..
Easy Storage & Widely Used: We provide you with a high-quality protective box for better storage. The compact body makes it effortless to carry anywhere. This electric rebar cutter is mainly used in construction sites, factory workshops, railway construction, bridge construction, building house, roads, etc..

Check Stock