Best Rear Engine Mount Replacement

Parts-Diyer Bicycle Engine Bike Motor Kit 80cc 2 Stroke Bicycle Petrol Gas Bike Motorized

Bicycle engine motor kit set Include cylinder top end, U-mount kit, brake lever, 44T rear sprocket, fuel tank, kill switch, carburetor and other necessary parts.
80cc 2-Stroke high power engine bike motor designed for 24", 26" and 28" bicycles, such as mountain bike, road bike, gravel bike, beach bike etc.
Reliable and durable engine motor kit improving bike performance will help accelerate your bike speed up to 30km/h.
Premium material and sophisticated workmanship ensure the quality of this bike engine motor kit.
For more specifications, please check the product description, and feel free to contact us if there any questions about the product or assembly.

5PCS SET -- You will get 16mm & 17mm Engine Mount Socket Wrench, 18mm & 21mm Rear Camber Adjusting Wrench, 24mm Oil Filter Removal Wrench, all marked with the number. 12 point, tilt angle design, used with 3/8'' drive..
WHY NEED IT -- 1) 16mm/17mm wrench used for removing nuts from engine fixing screw. 2) Offset 18mm/21mm wrench for adjusting rear axle camber. 3) 24mm oil filter removal wrench for models with common rail engines with DSG gearboxes, help you change oil without removing the battery..
1) 16MM & 17MM Engine Fixing Screws Wrench compatible with Mercedes Benz W124 W126 W140 W170 W201 W202 W203 W204 W210 W211 W219 W220 W221 models..

Gas Frame 2.4L Requirement on seatpost:27.2mm, Note: buyers need know how to fasten the motor on the pedestal mount of gas frame to prevent crack from vibration which maybe caused crack of frame.
Reinforced Black bicycle gas frame Built-in 2.4L gas tank Designed for the 2-cycle engines 48cc/66cc/80cc with 40 to 50mm wide front mount stud spacing.
Rear Disc brake bracket and front mount pedestal works well with gas motor front mount bolts 8mm.
Frame made especially heavy duty for gas engine applications Available with 135mm rear frame width for either single speed or multi-speed bikes..
38mm diameter downtube 70 degrees angle V frame, the width and Inner Diameter of the bottom bracket:68mmx50.8mm/2.677inx2in.
PLEASE NOTE 1: the best safe speed if racing: 35km/h；Head tube: 150mm.
This product Comes with 12months Warranty. Any questions,please contact us firstly! we can help you solve the problem until you are satisfied..

√ Easy to Install, Factory Direct Replacement Fittings.
√ Compatible with 2000 - 2013 Suburban, Yukon XL, Tahoe, Escalade Rear AC Block Off Fittings..
√ Eliminates the Rear A/C and Allows you to use just the Front System.
√ Simply disconnect the rear lines and install kit..
√ The fittings are installed at the connection location of the rear lines in the engine compartment..

Package includes 1pc Rear high mount third brake light. Compatible with Ford Explorer third brake light 2002-2010 and also replacement for Mercury Mariner 3rd brake light 2008-2011 rear center mount stop light and replacement for Ford Escape 3rd brake light 2008-2012 High Mount Stop Light, a pre cut 3m adhesive gasket, a rear window sprayer nozzle and washer, and rubber O-rings for the factory screws once you screw it in.
About this top rear light: Chrome Housing Red lens, Super Bright full LED lights. No need to worry about incandescent bulbs blowing or fading overtime.
How to install 02-10 Explorer third brake light: Installation is easy, clean the around the light mount area and remove any dirt or grime after removing your old light, and before installing the new taillight, take an extra minute and line up everything before exposing the super sticky 3M tape gasket seal to check for a good fit. Then attached to the light.
Note: please save your two screws because they are not included with the new light, use rubber washer to seal the screw to the light.
Waterproof: This 02-10 Mariner third brake light includes 1pc foam gasket and is generally waterproof. Please kindly put a little silicone or some clear RTV all round the light to help seal it just ....

Fits: 1 1/4" (32mm)engine guards or frame..
Allow you to mount highway footpegs(male mount) on engine guard.Allow you to fold up foot pegs when not in use.
Packge included:A pair of 1.25"（32mm） Foot peg mounts With Hardware(As Picture shown).

Compatible with Toro: 8-32 Rear Engine Rider, 11-32 Rear Engine Rider, 10-32 Rear Engine Rider, 12-32 Rear Engine Rider.
Compatible with Toro: 56138, 56145, 56150, 56155, 56165, 56170, 56175, 56176, 56177, 56185, 56190, 56195, 59111, 59122, 59176, 59178.
Replaces OEM Part Numbers: Toro: 47-1420.