Best Raspberry Pi Camera Case Enclosure

Arducam 16MP Autofocus Quad-Camera Kit for Raspberry Pi, 16MP IMX519 Autofocus Synchronized Raspberry Pi Camera, Compatible with Nvidia Jetson Nano/Xavier NX

Designed for Raspberry Pi Camera: This Quad- Camera kit allows you to connect four 16MP IMX519 raspberry pi cameras to a single standard pi board and capture images or video at the same time..
Four in One: Combine four cameras into one frame, each with a resolution of 1/4.
the maximum output you can get: 4656 x 3496 for still images and 1920x1080 for video. Please note the frame rate for video and still images will drop to half the frame rate you would normally get with a single camera..
Wide compatibility: It is compatible with the latest Raspberry Pi camera software (libcamera) and uses the official Pi camera tuning algorithm. It also supports multi-platform multi-camera solutions such as Raspberry Pi, Jetson Nano, Xavier NX and many more. And this Camarray HAT is also compatible with Raspberry Pi 3 and Raspberry Pi (V1/V2/HQ) cameras..
Applications: Multiple camera processing technologies have enabled VR (Virtual Reality), AR(Augmented Reality), and other applications like SLAM (Simultaneous Localization and Mapping). Synchronized video streams with Raspberry Pi could be used for many use-cases (e.g., stitching, 3D sensing, tracking, …) before investing in an expensive video multiplexer hardware..
Please note: The cameras in the set are specifi....

Check Stock

MakerFocus Raspberry Pi 3 Case Protective Case, Raspberry Pi 3.5 inch Display Case, with Mini Cooling Fan for Raspberry Pi 3B, 3B+,2B,2B+ Compatible with Raspberry Pi GPIO 3.5 inch Display

Installation instructions video: Please get the link from the product description below. PLZ NOTE: ★This case is not compatible with 3.5 Inch HDMI TFT LCD Display, It is designed to RPI 3.5 Inch GPIO Display, ★The 3.5 inch screen is not included!!!.
Dual-use: You can use it only on the Raspberry Pi motherboard, or use it on the Raspberry Pi motherboard and Raspberry Pi 3.5inch display,Then decide whether to cover the its cover. (Note: The Raspberry Pi motherboard and Raspberry Pi 3.5inch display are not included!!!).
Can install mini cooling fan: The case when used without the display screen, you can install mini cooling fan, Snap-in installation, the cooling fan was included in packaging..
With GPIO open position: There is a GPIO open position on this case cover,when you use it only with Raspberry Pi motherboard, it can easy to pull up and insert the GPIO pins, don't need to open the cover. This case is easy to install and has good ventilation..
With cable guide hole: It reserved cable guide hole for the camera, more convenient to use with camera.

Check Stock

Arducam Raspberry Pi Camera Module 3 Wide, 120°(D) IMX708 Autofocus Pi Camera V3 with Acrylic Case, 15cm 15-22 Pin FFC Cable

Compatible with all Raspberry Pi boards: Raspberry pi camera v3 works with all Raspberry Pi models, 4B/3B, Pi Zero W/2 W..
Based on IMX708 sensor with HDR, 4608 x 2592 is the highest resolution you can get for still images, 1080p50 max for video..
The autofocus of pi cam v3 is achieved by a mixture of PDAF and CDAF, ensuring crisp and clear images..
Fully support libcamera and Picamera2, and uses CSI-2 serial data output with 2-wire serial communication for seamless integration..
Come with a 15cm 15-22pin camera cable, especially for Raspberry Pi zero 2 w.
also an acrylic camera case included, easily mount on any tripod with 1/4"-20 mounting screws..

Check Stock

Arducam Sensor Extension Cable for Raspberry Pi Camera Module V2, 300MM/1FT Cable to Extend IMX219 Sensor for Smaller Enclosure, Narrow Space Project, Work with V2 Camera on Jetson Nano

Fresh Design: A fresh Arducam design to extend your camera vision on the Raspberry Pi Camera Module V2 – peel off the sensor from the connector on the camera board and put our cable in between. It does NOT support 5MP V1 cameras or any other sensors..
Fresh Look: Give your Raspberry Pi Camera Module V2 a fresh look by freeing the sensor from the camera board without losing the traditional flex ribbon cable extension.
Fresh View: Having got rid of the restrictions caused by the camera board, you can now see in a new perspective and put the camera in a smaller enclosure and narrow space, like through a small hole or a tube.
Fresh Option: The extension cable is compatible with Arducam IMX219 Sensor drop-in replacement modules including IMX219 autofocus and IMX219 M12 lens series. Those combinations will also work with the NVIDIA Jetson Nano.
Note: Please detach and re-attach the connectors gently and carefully, otherwise you might cause damage to the connection. The Raspberry Pi Camera Module V2 is NOT included..

Check Stock

Infrared Night Vision IR Camera for Raspberry Pi 4 Pi 3b+ Video Webcam with Case Suits for 3D Printer

New design Acrylic holder case make sure your pi camera is more stable and flexible, the case reserve the hole for heat-sink, IR led and screws hole,....
Compatible with all series, fit for Raspberry pi 4, Pi 3 B+ with 100cm FFC Camera Cable, and match 30cm FPC Cable for Pi Zero, also can works with....
HD resolution, the night vision camera is capable of 2592*1944 pixel static images, and also supports 1080P 30fps, 720P 60fps and 640*480P 60/90fps....
Better low light performance, IR corrected lens to reduce focus shift at night, and IR LED illuminator to improve the lightning condition.
Typical usage scenarios, Home security and surveillance, motion detection, 3D printer observe, time-lapse photography and other Raspberry Pi camera....

Check Stock

Aoicrie for Raspberry pi Zero Camera Module 5MP 1080p OV5647 Sensor Video Compatible with Pi Zero Ribbon Cable&FPC Cable for Raspberry Pi Model A/B/B+,Pi 2 for Raspberry Pi 3,3B+ Pi Zero/Zero W Pi 4

for Raspberry Pi Zero CSI Camera Module with Fixed Focus Lens Camera module for Raspberry Pi, Fully compatible for Raspberry Pi A, B, B+, 2, 3, 3B+.Pi 4.Zero Zero W and 720p The camera is supported in the latest version of Raspbian,the for Raspberry Pi's preferred operating system.Work natively with all for Raspberry Pi models for your new project or drop-in replacement..
High-Definition video camera, The sensor itself has a native resolution of 5 megapixel. In terms of still images, the camera is capable of 2592 x 1944 pixel static images, and also supports 1080p @ 30fps, 720p @ 60fps and 640x480p 60/90 HD video recording.Easy plug and play type capability，Can be applied to image recognition and image tracking..
Both cables 2 cables included between the camera connectors for the Pi Zero and Model A&B series,The module attaches to for Raspberry Pi, by way of a 15 Pin Ribbon Cable, to the dedicated 15-pin MIPI Camera Serial Interface (CSI), which was designed especially for interfacing to cameras.15CM Golden Ribben Flex Cable for Raspberry Pi Zero Zerow, model: FPC.
5.90in/15cm and 19.68in/50cm white camera cable for Raspberry Pi Model A/B/B+, Pi 2 and for Raspberry Pi 4 3, 3B+, model: FFC.The C.
Connect the included ribbon cable to the CSI (Camer....

Check Stock

UCTRONICS Fan Adapter Board for Raspberry Pi Upgraded Complete Enclosure and Raspberry Pi Cluster Case, Compatible with Raspberry Pi 3/3B+/4B, Output 5V Power

This fan adapter board is designed for Raspberry Pi desktop cluster cases and supports any Raspberry Pi motherboard with micro USB or USB C power..
With 4 pins on the adapter board, it can provide 5v power to two fans, which is the best way to power your fans when your Raspberry Pi GPIO is occupied by the PoE hat and keep your device cool at all times..
Plug and play: The fan adapter fits any 5V fans with an XH2.54 duplex connector. Simply plug the red wire of the fan connector into the positive and the black wire into the negative to run. Size:0.51*0.59 inch..
Compatible ASIN List: Raspberry Pi Complete Enclosure: B09JNHKL2N, B09S11Q684.
Raspberry Pi Cluster Case: B099RR1ZCT, B09K439BTY all are suitable for this fan adapter..

Check Stock

KOOKYE Raspberry Pi 4 Enclosure Black+Type C Power Supply USB-C 5.1V 3A+Heat Sinks+Cooling Fan

【User-friendly Design Raspberry Pi 4 Case 】 Unique（Individual） Removable Top Cover Design. This case have multilayer, including removeable plastic panel, bottom plastic panel and high-quality case, you can disassemble the panel and get in touch with the GPIO or camera connector very simple and easy..
【Power Supply】5.1V / 3.0A DC output,1.5m captive cable with Type-C output connector.Designed for Raspberry Pi 4 computer to provide enough electricity supply for your Raspberry Pi 4. Moreover this charger charges all other smartphone devices that has Type-C port as well..
【Cooling Fan】 With 30mm quiet cooling fan，it can drop the temps for your raspberry pi 4 and provide dual cooling effect.The fan with connector have two mode: full speed cooling and quiet cooling, you can choose the model as per yours needs..
【Heat Sinks】 3 different size aluminum heatsink with 3M for the Latest Version Raspberry Pi,Reduce chip hot-spots and increase thermal dissipation surface area..

Check Stock

Semi-Enclosed Enclosure Kit for Raspberry Pi BeagleBone Arduino UNO Mega

This is a multi-purpose semi-enclosed enclosure kit, Supports Raspberry Pi 1 Model A+ / Pi 1 Model B+ / Pi 2 Model B / Pi 3 Model B / Pi 3 Model B+ /....
It can be assembled very flexibly as a semi-closed enclosure, or as a two-layer bracket, or if you buy multiple sets, it can be used as a Raspberry Pi....
The space between the lower cover and the upper cover is 40mm, support Raspberry Pi direct stack HAT module, or Arduino stack SHIELD module, or....
The material of the lower cover and upper cover is 1.5mm thick aluminum plate, which is very strong, spacer/standoff and screws are nylon material..
Packing list: 2x covers, 8x M4x40mm standoffs, 4x M4x10mm spacers, 4x M4x8mm screws, 16x M2.5x6mm screws, 8x M2.5x10mm spacers (for Arduino MKR module....

Check Stock