Best Raspberry Gpio Breakouts

waveshare for Raspberry Pi Pico Evaluation Kit B Include Pi Pico Board with Pre-Soldered Header,1.14inch RGB Color LCD, 10DOF IMU Sensor Module,Dual GPIO Expander,Breadboard

Raspberry Pi Pico Evaluation Kit inlclude Raspberry Pi Pico with pre-soldered header ,1.14inch LCD Display Module,10-DOF IMU Sensor Module,Dual GPIO Expander ,830 Quality Breadboard etc.
Raspberry Pi Pico Board,a tiny, fast, and versatile microcontroller board,Built Using RP2040 Microcontroller Chip Designed By Raspberry Pi.
1.14" LCD Display Module for Pico ,Embedded ST7789 Driver, Using SPI Bus.
10-DOF IMU Sensor Module,an IMU sensor expansion module specialized for Raspberry Pi Pico. It incorporates sensors including gyroscope, accelerometer, magnetometer, baroceptor, and uses I2C bus for communication..
Dual GPIO Expander for Pico,Two Sets Of Standard Raspberry Pi Pico GPIO Male Headers.

Raspberry Pi Pico GPIO Expansion Board is used to break out all the pins and power of the Raspberry Pi Pico development board via male or female headers.
Pico GPIO Expansion Board allows the user to connect it to other components with the help of a jumper wire.
It has been designed to enhance the learning experience for the user.
GPIO Expansion Board is specifically made to work with the Raspberry Pi Pico Board.
Compatible with all the variants of Sensors/Modules.

GPIO status LED and power 5V / 3.3V indication..
GPIO output or input level high LED on, output or input level low LED off. 5V blue, 3.3V red, GPIOs green. The position of the LED is in a one-to-one correspondence with the position of the Raspberry Pi 2x20pin connector, and the logic level of the GPIO can be observed very quickly and intuitively. The driving current of each LED is only 0.1mA, so you don't have to worry about it affecting the read and write status of GPIO..
Support for Raspberry Pi A+, 3A+, B+, 2B, 3B, 3B+, 4B.
Terminal block pitch 3.5mm, wire size range 26AWG to 16AWG, strip length 5mm, screw M2 steel, pin header and cage copper. 2 x 20 pins expansion pin header, height 8mm..
Packing list: 1x terminal block breakout module, 4x M2.5x16mm nylon standoffs, 4x M2.5x6mm nylon standoffs, 4x M2.5 nylon nuts(NOTE: the item not include Raspberry Pi module).

【Updated Starter Kit for Raspberry Pi】This is a updated Assembled starter kit for for Raspberry Pi 4B/3B+/3B/2B/B+, including GPIO Adapter Board with Wiring Diagram Card, 40pin GPIO Rainbow Fat Cable, 830 Tie Points Solderless Breadboard and 65pcs Jumper Wire..
【GPIO Adapter Board with Wiring Diagram Card】You can connect much version raspberry of the board to various sensors and electronic components with the GPIO extension board..
【40pin GPIO Rainbow Fat Cable】IDC 40pin Male to Female Ribbon Cables Kit flat GPIO Cable.
Material: High-quantity copper soft wire material for safe and durable.
Easy assembly:The cables can be separated to form an assembly wires to support non-standard odd-spaced headers to complete other tests..
【830 Tie Points Solderless Breadboard】made of high quality ABS plastic, each row and columns has corresponding letters and numbers, reduce the mistake handling, with self-adhesive tape on back and multiple links to buckle..
【65pcs Flexible Jumper Cables】Flexible, durable, reusable, easy to connect and disconnect.
4 Kinds of length: 12cm(49pcs), 16cm(8pcs), 20cm(4pcs), 24cm(4pcs).
these jumper cable wires can connect each other through the pin connection, do not need welding, can fit for fast circuit....

Compatible with Raspberry Pi Zero/Zero 2 and Raspberry Pi Zero W/Zero W 2 (Raspberry Pi Zero Board is Not Included).
Case with Power Supply, refer to ASIN B09Q5CHCGX.
The heatsink is for better heat dissipation and GPIO header makes it easy to connect the GPIO ports..
Acrylic case with 2 covers and screws to install..
Access to all ports of Raspberry Pi Zero Board..
Package includes a case, heatsink, switch cable, OTG cable, HDMI adapter, GPIO header, and a screwdriver..

8" 40 Pin Ribbon Cable for Raspberry pi 3B ,Raspberry pi 2 model B,Raspberry pi 1B+, Raspberry pi 1A+,Raspberry pi zero W, Raspberry pi zero.
Pin Pitch: 2.54 mm,Their Diagram as Product image show.
2x40 Pin Male to female IDC 2.54mm pitch ribbon cable flat GPIO Cable.
GPIO 40P 40-pin Rainbow Ribbon Cable.Raspberry Pi 3 2 Model B B+ and 3.5¡± 5 inch TFT touchscreen LCD display are not including..
SamIdea is a Registered Trademark, can not sold without authorization..

The item has been soldered and assembled. Support for Raspberry Pi A+ 3A+ B+ 2B 3B 3B+ 4B.
GPIO status LED and power 5V / 3.3V indication. GPIO output or input level high LED on, output or input level low LED off. 5V blue, 3.3V red, GPIOs green. The position of the LED is in a one-to-one correspondence with the position of the Raspberry Pi 2x20pin connector, and the logic level of the GPIO can be observed very quickly and intuitively. The driving current of each LED is only 0.1mA, so you don't have to worry about it affecting the read and write status of GPIO..

The small board is connected to the 40-pin GPIO connector on the Raspberry Pi, and these pins are assigned to a breadboard-friendly layout and spacing.
T-shaped expansion board and breadboard make the experiment more convenient.
Using the GPIO expansion board, you can connect all versions of the Raspberry Pi to various sensors and electronic components.
Purpose: It can be used for the pin experiment of the experiment board, adding experimental items, etc., and it can be connected to the pin very reliably by simple soldering by yourself. 5. Strong compatibility: suitable for Raspberry Pi 3B/3B+/4B, 100% compatible with Raspberry Pi.
Strong compatibility: suitable for Raspberry Pi 3B/3B+/4B, 100% compatible with Raspberry Pi.