Best Rail Coping Sled

3-1/2\ To 4-1/2\ Universal Fence Clamp 2 Pack

  • Our 525 Large Coping Sled works on both the router and shaper, either in the miter slot or against the fence. This is the safest and most accurate way to make cope cuts and other cross-cuts on a router table or shaper. Don't try to cope without it! Two adjustable feed handles provide firm control over the sled and your work..
  • Includes an 11-3/4" adjustable steel miter bar that mounts in 6 different locations for best placement. Can also be used without the miter bar against your fence..
  • Holds stock up to 10" wide. Heavy duty 1/2" phenolic base (15-3/4" x 15-3/4") will not distort from clamp pressure..
  • Features one 500 lb. Outboard Toggle Clamp and two 500 lb. Inboard Toggle Clamps. Hold stock up to 1-3/4" thick, or 2-3/4" with optional 6305R Riser Kit (one Riser Kit required for each toggle clamp). Fence is 24” long. Optional 525S Flip Stop available for repetitive work..
  • Lifetime guarantee against defects in material or workmanship. Made in the USA!.
Check Stock

Router line Storage Box Power Cord Socket Sorting Box Set-top Box Rack

  • Our 526 Medium Coping Sled works on both the router and shaper, either in the miter slot or against the fence. This is the safest and most accurate way to make cope cuts and other cross-cuts on a router table or shaper. Don't try to cope without it! Two adjustable feed handles provide firm control over the sled and your work..
  • Includes an 11-3/4" adjustable steel miter bar that mounts in 6 different locatons for best placement. Can also be used without the miter bar against your fence..
  • Holds stock up to 6" wide. Heavy duty 1/2" phenolic base (11-5/8" x 11-3/4") will not distort from clamp pressure..
  • Features two 500 lb. Inboard Toggle Clamps. Hold stock up to 1-3/4" thick, or 2-3/4" with optional 6305R Riser Kit (one Riser Kit required for each toggle clamp). Fence is 12” long. Optional 525S Flip Stop available for repetitive work..
  • Lifetime guarantee against defects in material or workmanship. Made in the USA!.
Check Stock

Peppa Pig - Pumpkin Party

  • 【Universal Fits】Size: 38x11cm/ 14.96x4.3 inch. Suitable for all kick scooter. Suitable for be used downhill, flat snow, sand and grass.
  • 【Durable Material】The ski sled board is made of high quality PE material and has good low temperature resistance. It works fine at -20 degrees....
  • 【Easy Installation】Just remove the axle bolts and wheels on your existing kick scooter and install the the skis in place of wheels.
  • 【Portable】Ski sled board is light and portable, you can take it with you.
  • 【A Gift For Children】The ski dual-use sled is the best gift for your child to enjoy themselves, add a rail kit to your scooter skis and you can....
Check Stock

Phonleya WiFi Router organize Box Set-Top Box Rack Patch Panel Storage Shelf Hider Cord Management Container Storage Box for Desktop

  • Our 528 Small Coping Sled works on both the router and shaper, either in the miter slot or against the fence. This is the safest and most accurate way to make cope cuts and other cross-cuts on a router table or shaper. Don't try to cope without it! Two adjustable feed handles provide firm control over the sled and your work..
  • Includes an 11-3/4" adjustable steel miter bar that mounts in 6 different locations for best placement. Can also be used without the miter bar against your fence..
  • Holds stock up to 6" wide. Heavy duty 1/2" phenolic base (7-5/8" x 11-5/8") will not distort from clamp pressure..
  • Features one 500 lb. Inboard Toggle Clamp. Hold stock up to 1-3/4" thick, or 2-3/4" with optional 6305R Riser Kit (one Riser Kit required for each toggle clamp). Fence is 12” long. Optional 525S Flip Stop available for repetitive work..
  • Lifetime guarantee against defects in material or workmanship. Made in the USA!.
Check Stock

18” Precision Steel Miter Bar Rail Runner with Adjustable Spring Loaded Plungers For DIY Table Saw Crosscut Sleds, Jigs and Fixtures to Slide in 3/4 inch by 3/8 inch Miter Slots

  • ...n the bar to mount the bar using #8 wood screws (not included)..
  • Once you mount the bars to your sled, jig or fixture you are sure to feel the difference. This is especially true when you first run the bars through your miter slots. The smooth sliding action is perfect for crosscut sleds, miter angle jigs, shop made coping sleds and a whole lot more! Using two bars (only one is included) for even more stability works exceptionally well..
  • The bar is approximately 18 inches long and will fit into miter t slots and u-shaped miter slots. Non-standard slots found on some job site style table saws and other small machinery will not accept this bar due to the non-standard slot dimensions. We recommend that you measure your miter slot before placing your order..
Check Stock

Glide Gear TMP 1000 Professional Video Camera Tablet Teleprompter

  • 15mm Rail system, adjustable height camera sled with multiple 1/4 and 3/8 options.
  • hard plastic carry case, 1 or 2 tripod set up.
  • adjustable height camera sled with multiple 1/4 and 3/8 options.
Check Stock

TECH DECK, Danny Way Mega Half Pipe X-Connect Park Creator, Customizable Ramp Set with Exclusive Plan B Fingerboard, Kids Toy for Boys and Girls Ages 6 and up

  • CUSTOMIZABLE PARK: Design and build your custom mini skateboard park with the Danny Way Tech Deck Mega Half Pipe X-Connect Park Creator ramp set. Set up different combinations with ramps, coping, rail and more..
  • EXCLUSIVE FINGERBOARD: Add to your finger skateboard collection and skate your creation with the exclusive Danny Way signature Plan B Skateboards finger skateboard included in the set..
  • COMBINE MULTIPLE SETS: With the X-Connect Park Creator series ramps, you can connect multiple sets such as the Flip N’ Grind, Competition Wall and Sk8 Garage ramp sets (each sold separately) to build the ultimate facility for you to shred..
  • X-CONNECT PARK CREATOR: Drop into a halfpipe, slide the coping, grind the rail, or set up and customize the park in any way you like. Use X-Connect Park Creator ramps with your Tech Deck fingerboard collection or Tech Deck BMX (each sold separately)..
  • PERFECT FOR EASTER BASKETS: Tech Deck toys are perfect Easter basket stuffers and make great Easter gifts for kids aged 3 and up. Collect them all (each sold separately)!.
Check Stock

2 Pcs Snow Scooter Ski Sled Kit Sand Scooter Conversion Kit Fold Skate Board Outdoor Snow Scooter Sled Ski Attachment for Outdoor Black

  • 2 Pcs Snow Scooter Ski Sled Kit Sand Scooter Conversion Kit Fold Skate Board Outdoor Snow Scooter Sled Ski Attachment for Outdoor Black.
  • Durable Material: The ski sled board is made of PE material and has good low temperature resistance. It works fine at- 20 degrees Celsius. It is durable and wear resistant for long term use..
  • Universal Fits: 38 x 11 cm/ 14.96 x 4.3 inch. Suitable for all kick scooter. Suitable for be used downhill, flat snow, sand and grass..
  • Easy to Install: The scooter ski sled is easy to install and can be interchanged with just a screws without complicated installation process..
  • Snow Scooter: a rail kit to your scooter skis and you can ride at your favorite ski resort. Not include scooter..
Check Stock

Miter T-Bar for Jigs Fixtures Sleds Router Tables and General Woodworking 48 inch MADE IN THE USA

  • ...f extruded aluminum and can be cut into sections and drilled as needed. Typical uses for the T-bar are fixtures like featherboards where the featherboard needs to be kept stationary to apply consistent pressure. The T-bar also works great for sleds and other sliding fixtures like cutoff sleds on a table saw or coping sleds on a router table..
  • When mounting the Miter T-Bar it is a good idea to keep in mind that the “T” on the bottom of the track is approx. 1/8” tall, which is just enough to clear the t-slot on most miter slots. If mounted directly to platform for a sled, the tabs may catch and prevent the sled from sliding freely. To remedy this, we recommend using washers between the mounted track and the platform to allow the sled to slide as desired..
  • The Miter T-Bar can also be mounted upside down by cutting a dado slot into your sled platform that is the same depth as the T on the Miter T-Bar. The Miter T-Bar will then act much more like a standard solid miter bar. Using this type of flush mount may work better in certain situations when compared to the traditional method..
  • When we decided to start manufacturing aluminum tracks many years ago (well over 20 years), we thought that it was very important to do our best to keep the manufactur....
Check Stock