Best Push pull Solenoid

Fielect DC 12V 10A 80N Push Pull Type Solenoid Electromagnet 20mm Open Frame Solenoid Electromagnet, Linear Motion, JF-1683B 1 Pcs

【Size】- 52 x 58 x 83mm / 2.05 x 2.28 x 3.27 inch(L*W*H).
【Good design】- Push pull Type, linear motion, frame type, plunger spring return, 12V DC solenoid electromagnet..
【Advantages】- Solenoid 12V simple structure, small volume, high adsorption force.copper coil inside, has good temperature stability and insulation, high electrical conductivity..
【Application】- DC 12v solenoid electromagnet use in vending machines, transport equipment, office facility household appliance, mechanical, etc game machine,Sorting machine,auto door lock,etc..
【Noted】- As an actuating element of an automation equipment ,because the current is large, the single cycle can not be electrified for a long time.The best operate time is in 2 seconds..

Check Stock

Fielect DC 12V 15N Push Pull Type Tubular Solenoid Electromagnet, Linear Motion, MQ8-Z15B-12V

【Dimension】- 30x 30x 50mm/1.18" x 1.18" x 1.96"(L*W*H).
【Good design】- Push pull Type, linear motion, frame type, plunger spring return, DC solenoid electromagnet,easy to install..
【Advantages】- This solenoid has simple structure, small volume, high adsorption force.copper coil inside, has good temperature stability and insulation, high electrical conductivity, simple control, energy saving and reliable, support DC voltage..
【Application】- Solenoid electromagnet widely used in vending machines, transport equipment, office facility household appliance, mechanical, etc game machine,Sorting machine,auto door lock,etc..
【Noted】-As an actuating element of an automation equipment ,because the current is large, the single cycle can not be electrified for a long time,best operate time is in 25 seconds. The picture label data is inaccurate, the actual suction is subject to the title.

Check Stock

Ximimark 2Pcs JF-0530B DC12V 300mA 5N/10mm Push Pull Type DC Solenoid Electromagnet Magnete

【Dimension】- 22 x 25 x 26mm/0.86" x 0.98" x 1.02"(L*W*H).
【Good design】- Push pull Type, linear motion, frame type, plunger spring return, DC solenoid electromagnet,easy to install..
【Advantages】- This solenoid has simple structure, small volume, high adsorption force.copper coil inside, has good temperature stability and insulation, high electrical conductivity, simple control, energy saving and reliable, support DC voltage..
【Application】- Solenoid electromagnet widely used in vending machines, transport equipment, office facility household appliance, mechanical, etc game machine,Sorting machine,auto door lock,etc..
【Noted】-As an actuating element of an automation equipment ,because the current is large, the single cycle can not be electrified for a long time,best operate time is in 8 seconds. The picture label data is inaccurate, the actual suction is subject to the title.

Check Stock

uxcell a14092600ux0438 Open Frame Actuator Linear Mini Push Pull Solenoid Electromagnet, DC 4.5V, 40 g/2 mm

Product Name : DC Solenoid Electromagnet.
Body Size : 20 x 12 x 11mm / 0.8" x 0.47" x 0.43"(L*W*T).
Plunger Bar Size : 3 x 40mm / 0.12" x 1.6"(D*L).
Package Content : 1 x DC Solenoid Electromagnet.

Check Stock

1\ Bore X 24\ Stroke Double Acting Pneumatic Cylinder (Roughly 1\ Bore 20MM)

These pneumatic cylinders are what everyone uses to make Halloween Props. They are extremely versatile, and have tons of mounting options that will allow you to set up your prop in may different ways.
You can also use these with a 2-way or 3-way solenoid if you are using gravity/weight to push the cylinder back down. When the solenoid is triggered, air is applied through the bottom hole - forcing rod up very quickly..
Examples: Lid Opener Pop-up props Moving Skeletons or Zombies Door Banger Coffin Lid Banger Barrel Lid Banger Monster in a Box Trash Can Trauma Bore.
These double-acting cylinders extend quickly when air is applied, and snap closed quickly when Solenoid is triggered (when used with a 4-way solenoid)..
This is the measure of the diameter of the cylinder. Bigger bore size = more air required to open cylinder = more torque (power) to move things. With this roughly 1" BORE, you will get about 100 lbs. of force at 100 PSI of air pressure. Stroke: This is the measure of how far out the shaft of the cylinder will extend when fully extended. Air Holes: Cylinder comes with two push-in fittings that accept 1/4" airline..

Check Stock

DORMEYER 1000-M-1 Solenoid, Open Frame, Pull, Continuous

Solenoid Type: Laminated Item: Solenoid Duty Cycle: Continuous Stroke Range: 1/8" to 1" Pull Force Range: 92.8 to 176.0 oz. Coil Volts: 120VAC Seated Amps: 0.48 Seated Watts: 19.0 Terminals: Solder Lug Coil Amps @ Max. Stroke: 6.50 Mounting Holes: 2 x 1-5/8" Gravity Value: 5.92 oz. Pull @ 1/2 In. Stroke: 13.0 oz. Pull @ 1/8 In. Stroke: 65.0 oz..
Pull @ 1/4 In. Stroke: 35.0 oz. Pull @ 3/8 In. Stroke: 20.0 oz. Pull @ 5/8 In. Stroke: 5.0 oz. Width: 2-1/16" Pull @ 1 In. Stroke: 1.0 oz. Length: 2-1/2" Pull @ 3/4 In. Stroke: 3.0 oz. Depth: 2-1/16" Coil Resistance: 14.9 ohm Country of Origin (subject to change): United States.

Check Stock

mistcooling 250 PSI Misting Pump

250 psi pump quiet operation 35Db solenoid valve – Controls flow of water in the pump in built filter – helps protect your misting nozzles built in water by pass self-priming.
Nickel-plated brass button series With stainless-steel Orifice Standard 10/24-inch thread 0. 012-inch Orifice Rust-resistant fixed impeller pin 0. 014 GPM Flow per Nozzle.
Maximum inlet pressure: 100 psi Minimum inlet pressure: self- priming. Maximum outlet pressure: 250 psi (depends on line length and numbers of nozzles) maximum flow: 0. 9 GPM full load Amps. 110V AC: 0. 7 amps 12V DC: 4. 0 amps Voltage: 110V-220V AC/ 12V DC (refer manufacturing label on the pump) noise level: 40 dB. Maximum fluid temperature: for room temperature/ cold water applications only.
Max pressure 250 psi Available in 110 V, 220 V & 12 VDC Durable Rust Proof Enclosure Thermal Safety Switch Oil-less Pumps may generate heat, motor manufacturer have installed built-in thermal safety switch to improve the longevity of pumps Standard pump inlet: 3/8-inch push lock Fitting. Standard Pump outlet: ¼ inch Push-lock fitting. Max pressure 250 psi 110 V AC.
1. Solenoid Valve Solenoid valve controls the flow of the water in to the pump. You may leave the inlet water source on at all the time. Water will enter th....

Check Stock

Industrial Misting System - Patio Misting System - 250 PSI Misting Pump, Stainless Steel Tubing - For Residential. Commercial, Outdoor Restaurant and Industrial Misting Application (20 Nozzle System)

Base 20 Nozzle Stainless Steel Mist Kit Includes: 250 psi mid pressure pump with built-in solenoid and filtration 38ft Stainless Steel tubing for push lock (Pre-cut 2ft sections) 22ft UV coated Flexible 1/4" feed line 20- Nickel Plated Push Lock Misting Tees 1- End plug 2- Nozzle plugs 20- Nickel plated brass/stainless steel Nozzles (0.012") Stainless Steel Mounting Clamps and all necessary fittings required for easy D-I-Y installation.
Misting Pump Features : Stainless Steel Mist Line Whisper quiet operation Built in Solenoid Valve Built in Filtration Outdoor Enclosure Wall Mountable Steel Enclosure Max Pump Pressure 250 Psi 110v AC Supports up to 30 nozzles Cleanable Brass-Stainless Steel ultrafine misting nozzles Reusable high pressure push lock fittings Stainless Steel Clamps.
Applications Include : Residential Patio Misting Greenhouse Humidification Commercial Outdoor Cooling Outdoor Restaurant Misting Industrial Misting.
Do it yourself misting system, easy to install, with Push to Connect Nickel plated fittings, rated for 1800 PSI..

Check Stock

3-Way Solenoid Valve 3/8\ with All Fittings (12-Volt)

These have an air inlet, an air outlet and an exhaust port..
Allow a much greater amount of air to flow through the valve and into your prop. Great for props that need a lot of lift or a quick lift..
Can be used with Single-Acting Cylinders with or without an air hole because the air can escape back through the solenoid and out the exhaust port (if open)..
Allow you to control the exhaust coming out of the solenoid if you want to slow down the action on the tail end of your prop's motion..
Has two 3/8" air ports and one 3/8" breather port. Comes with: 3/8" 3-Way Solenoid (2) 3/8" Male Straight fittings with 3/8" push-in female (1) Brass Breather Vent Available with 12-Volt, 24-Volt, or 110-Volt Flying Lead.

Check Stock