Best Pressure Flow Meter

AUTOOL EVAP Vacuum Automotive Smoke Machine Leak Detector Diagnostic Tester

  • ...ay be located in other locations. Open the plastic cover of the EVAP service port, then use the spool wrench to remove the check valve clockwise, then install the EVAP service port adapter, and introduce smoke from the port into the EVAP leak detection system..
  • 【External Pressure Gauge】You can observe the barometer to more accurately determine whether the car pipeline is leaking. If the barometer index keeps increasing, there is no problem with your car’s pipeline. If the barometer index keeps decreasing, your car’s pipeline leaks need to be repaired, and there is a barometer test. Leakage is faster and more accurate.
  • 【External Flow Meter】You can easily control the air pressure, because the air pressure of each pipe in the car is different. If the air pressure is too high, the pipe will be damaged, and if the air pressure is too low, the leak will not be detected. Therefore, the flow meter is very important to protect your detection system more effectively. Make testing safer.
Check Stock

MR CARTOOL T110 Automotive EVAP Smoke Machine, 12V Car Fuel System Leak Tester Detector with Built-in Vacuum Pump & Pressure Gauge & Air Flow Meter for All Vehicles

  • Smoke Mode】Built-in air pump and smoke generator, so it does not rely on additional air machine, perfect for Mobile Automotive Repair! The smoke can be produced within 10 seconds, dramatically reducing diagnostic time. Smoke output value: 6L/min..
  • 【Flow Meter & Pressure Gauge】Equipped with pressure gauge and adjustable flow meter to help maintenance personnel to observe the current flow volume and pressure for better control the smoke effect. Built-in over-heat protection, if it exceeds working limit (Over 176℉), it will power off automatically..
  • 【Complete Set】Comes with 4.92ft Smoke Hose, EVAP Special Connector, Standard Cone Adapter, Power Cord Clamp, Valve Core Wrench, Airbag Adaptor, Rubber Connector Part, 3.38oz Empty Bottle for test oil(Please notice: Package does not includes the baby oil), Hanging Hook, Various of Soft Rubber and Hard Rubber Hose Plugs..
  • 【Worry-Free After-Sales】MR CARTOOL offers 24-month warranty and 7x24 hours friendly customer service to ensure your shopping experience. No need to pay extra for warranty service, saving you a lot of money! If you have any issues about the EV....
Check Stock

Argon CO2 Regulator - Welding Gas Flowmeter For TIG MIG - Brass Construction Flow Meter For Argon and CO2 Welder Tanks CGA580

  • ARGON/CO2 REGULATOR FOR WELDING: Terrabloom Argon Gas Flow Meter Regulator is Designed for Professional TIG/MIG Welding Applications. It Provides an....
  • ARGON FLOWMETER WITH PRESSURE GAUGE: In addition to allowing to adjust gas flow rate, our Argon CO2/Argon flowmeter contains a pressure gauge that....
  • TIG/MIG FLOWMETER INSTALLATION: TerraBloom Welding Pressure Regulator Seamlessly Connects To Standard Argon/Helium/CO2 Tanks with CGA-580 Inlet....
  • VERSATILE APPLICATIONS FOR CGA-580 Tanks: This Gas Pressure Regulator/Flowmeter Can Be Used with Argon, Helium and CO2 Gas Tanks (CGA-580 Inlet).
  • WARRANTY: Covered by TerraBloom's 30-day money back guarantee. 1 Year Warranty Against Manufacturing Defects.
Check Stock

BTMETER Digital Anemometer Barometer Handheld, for Wind Speed Temperature Wind Chill Tester w/Humidity, Altitude, Barometric Pressure Meter for Climbing Drone HVAC CFM BT-100WM

  • ➤【MULTIFUNCTION ANEMOMETER】BT100WM wind speed gauge meter measures not only Wind Speed, Wind Temp, Wind Chill Indicator, but also Relative Humidity, Dew Point, Barometric Pressure and Altitude. With data log, Tripod hole for mounting, it’s ideal for outdoor activities:Long Range shooting, Hunting, Sailing, Kite flying, Drone Driving, CFM air flow test..
  • ➤【HIGH PRECISION】Digital wind meter for measure wind speed range 0.67 ~ 67.1 mph( +/- 5% accuracy).
  • Wind temperature range -10~45℃,14℉-113℉(+/-2 ℃/℉).
  • Wind meter measurement altitude from 0-19685 Ft. Resolution: 0.2 mph, 0.2℉,0.1% RH. So you can be rest assured to get fast and accurate reading..
  • ➤【EASY TO USE】Measures different readings such as Max, Min, Average, Current Wind Speed, display in 5 units: mph, ft/min, km/h, m/s or knots. Temperature (Celsius/Fahrenheit), Elevation(M, Ft), Atmospheric pressure(inHg, hpa mbar). And LCD backlit screen makes it easy to read in day or at night..
  • ➤【LOG THE BAROMETER DATA】This handheld wind speed meter can also log 16 groups of barometric pressure data for record, compare and analyse the relationship between temperature, humidity, and height. It’s compact pocket sized Pro anemometer for weather station, long distance shootin....
Check Stock

Horiba 9096001700 Plastic Body PH Electrode

  • Modular design makes it suitable for use with output modules, sensors and remote transmitters.Compact structure, easy to install.Intuitive clear reading, high reliability, measuring accuracy is ±1%.High-definition displays show both instantaneous and cumulative flow.Can be widely used to measure diesel, kerosene, gasoline, etc..
  • This digital turbine flow meter has modular design, high accuracy, compact size and stable performance. Easy to replace and maintain internal components. Suitable for use with output modules, sensors and remote transmitters..
  • Malfunction and solution:The flow meter is not accurate. 1. The method of field calibration is not correct. Calibrate again. 2. The flow rate on the meter is below the lowest. Increase the flow rate. 3. The flow meter is blocked by the dry liquid. Take out the impeller and clean it carefully and make sure the impeller turns freely..
  • 4. The impeller is wrapped by the sealing material. Remove the meter and make sure the impeller turns freely. 5. Too close to the impeller. Install properly 6. Too close to the motor or electronic noise environment.
  • The meter can not calibrate. 1. Circuit board is break down. Replace the circuit board. 2. Button is fail to press. Replace the circuit board..
Check Stock

Argon CO2 Flow Meter Regulator with 80 Inches 6.6Ft Gas Hose for TIG MIG Welder 10 to 60 CFH - 0 to 4000PSI Pressure Gauge CGA-580 Inlet Precise Brass Flow Meter

  • [APPLICATIONS] - Our gas pressure regulator/flowmeter can be used with a variety of gas cylinders including argon, helium, nitrogen, and argon/carbon....
  • [CGA580 CONNECTION] - The Flow Meter Regulator is suitable for standard Gas tanks with CGA-580 inlet connection, with a unique filter port design on....
  • [MEASUREMENT UPGRADE] - The 4000PSI gas meter is more widely used than 3500PSI. If you need to measure more corrosive gases, facing some special....
  • [RELIABLE QUALITY] - The body of our gas flow meter is made of high-quality brass to withstand harsh environments and have a longer life. The....
  • [PACKAGED WITH HOSE] - Our argon regulator package comes with a 2m/6.6 Ft hose that will completely protect you from injury in adverse conditions and....
Check Stock

CGOLDENWALL Turbine Flow Meter Fuel Meter Digital Flowmeter with FNPT Thread, Flow Meter for Water Diesel Kerosene Gasoline, Flow Rate Range 2.5-26GPM (1 inch Flow Meter)

  • FLOW METER: Before use, please calibrate the flow meter with the liquid to be tested. And the flow rate of the liquid should exceed 2.5 gallons per minute, if the flow rate is too slow, the flow meter cannot measure normally. There is no battery included..
  • MULTI-FUNCTION DISPLAY: High-definition LCD display, can read single cumulative flow, instantaneous flow and total cumulative flow. The clear function can clear the value of cumulative flow, to make sure it is always within the measuring range. If your flow meter cannot work, please contact us in time..
  • HIGH-QUALITY MATERIALS: The aluminum alloy housing is sturdy, durable and corrosion-resistant, which have a long service time. The PCB circuit board make the battery have a long service life, and safe in use. Please NOTE: the LCD display is not water proof.
  • INSTALLATION: The flowmeter can be installed in horizontal and vertical directions, but the flow direction of the liquid needs to be consistent with the direction of the arrow on the flowmeter. There is no direction requirements for the installation of the display screen..
  • MEASURABLE LIQUIDS: The turbine flow meter can used for measuring the water, gasoline, diesel, kerosene, methanol and other low-corrosive, non-viscosity liquids..
Check Stock

Yeswelder Argon/CO2 Mig Tig Flow Meter Gas Regulator Gauge Welding Weld

  • Wide Application：Has CGA - 580 Tank fitting so it will screw right into the Argon, Argon/CO2Tanks. Ideal choice for MIG TIG welding, chemical and electronics industry.
  • Accurate Gas Flow Gague：The Square flow tube reads from 0 - 60 CFH, which is indicated by a ball which moves up and down in the flow tube.And has large 1 1/2" diameter pressure gauge which reads from 0 - 4000 PSI. Easy to read, accurate.
  • Multiple Outlet：Will fit both the female 9/16" x 18 nut or the male 5/8" x 18 fitting. It also comes with a standard 1/4" barbed fitting.
  • Design：Combination of regulator and flow meter.
  • Two Connection Ways：You can choose the connection method according to your needs.
Check Stock

MEANLIN MEASURE Argon Regulator Flow Meter with 6.5 Feet Hose,CGA580 Inlet Connection,5/8' x 18RH Outlet Fitting,Dual Output Argon Welding Flowmeter for TIG MIG Welder

  • 【Easy to Read】2″ gauges for easy reading. Makes adjusting your pressure values a piece of cake..
  • 【CGA-580 Inlet】This Gas Pressure Regulator Can Be Used with Argon, Helium and CO2 Gas Tanks,Ideal for MIG and TIG welding applications..
  • 【Accurate Measurement】This Gauge measuring range 0-4500PSI,It has a highly sensitive pointer to sense the pressure in the pressure tank,so it is more reliable than the flow-gauge style..
  • 【Excellent Quality】Our Double Dutput Argon Regulator Is Made Of Brass For High Strength, Toughness And Corrosion Resistance For Long Term Use..
  • 【Package Include】1*Argon Regulator Flow Meter 1* 6.5Feet Hose 2*Male 5/”8 UNF-18RH Fitting 2*1/4″ Hose Barb Adapter 2*Female 9/16″x18 Nut.
Check Stock