Best Precision Current Transformer

Gikfun DIY 5A Range AC Current Transformer Module for Arduino Pack of 5pcs EK1344x5

  • It's diy kits, need to solder by yourself.
  • onboard precision micro current transformer.
  • the module can measure AC currents less than 5A, the corresponding analog output 5A/5mA.
Check Stock

Suraielec 200W Low Voltage Transformer with Photocell Sensor and Timer, 120V AC to 12V/15V AC Multi Tap, Outdoor Weatherproof for Landscape Lighting, Individually Controlled Outputs, Weatherproof

  • 【Photocell Sensor & Countdown Timer】Landscape transformer with dusk to dawn sensor automatically turns low voltage pathway lights on at sunset, and off when sunrise. With countdown timer setting, you can illuminate spotlights and deck lighting auto on at dusk , then off at 4, 6, 10 hours interval as needed. Convenient and energy efficient for daily use..
  • 【2 Zones for Independent Control】Suraielec outdoor light transformer is equipped with two independently controlled outputs, allowing to setup 2 different landscape systems all controlled with a single transformer. That’s, you can set your front yard lighting stay lit till dawn while the backyard lights is set to be off 6 hours after sunset. Control home lighting separately..
  • 【Easy to Program & Install】Easy to operate with a push of button, the outdoor low voltage transformer is designed with 3 lighting modes: manual on/off- auto on/off- on at sunset and off 4/6/10 hours later, choose any preferred mode by Zone button. Two mounting holes for hanging the transformer more steadily, compact enough for easy concealment after installation..
  • 【Memory Function & Works with Smart Plug】 The low voltage transformer retains pre-set mode memory after power outage, no need resetting. By switching it ....
Check Stock

Suraielec 120W Low Voltage Transformer with Photocell Sensor and Timer, 120V AC to 12V/15V AC, Landscape Lighting Transformer with 2 Independant Zones,Weatherproof for Pathway Lights, Step Light

  • 【Photocell Sensor & Countdown Timer】Landscape transformer with dusk to dawn sensor automatically turns low voltage pathway lights on at sunset, and off when sunrise. With countdown timer setting, you can illuminate spotlights and deck lighting auto on at dusk , then off at 4, 6, 10 hours interval as needed. Convenient and energy efficient for daily use..
  • 【2 Zones for Independent Control】Suraielec outdoor light transformer is equipped with two independently controlled outputs, allowing to setup 2 different landscape systems all controlled with a single transformer. That’s, you can set your front yard lighting stay lit till dawn while the backyard lights is set to be off 6 hours after sunset. Control home lighting separately..
  • 【Easy to Program & Memory Function】Easy to operate with a push of button, the outdoor low voltage transformer is designed with 3 lighting modes: manual on/off- auto on/off- on at sunset and off 4/6/10 hours later, choose any preferred mode by Zone button. Features memory function, transformer retains its last mode setting after power outage..
  • 【Multi-Tap Outputs & Overload Protection】120W landscaping transformer converts 120 volt current to a low voltage current ( Selectable 12V AC /15V AC), achieving a safe an....
Check Stock

4Pcs 100A/50mA SCT013000 Non-invasive Split Transformer Sensor SCT-013-000 Split Core Current Sensor Transformer

  • ❤Applications❤Suitable for current measuring, monitoring and protection of AC motors, lighting equipment, air compressors, etc..
  • ❤Reliability❤Fully compatible with most similar products.
  • the number of opening and closing times is not less than 1000 (tested at 20℃).
  • this split core current transformer is particularly suitable which can use for a long time for DIY use and it works well with arduino and raspberry pi..
  • ❤Specification❤Opening size: 13mm × 13mm.
  • lead length: 1.5 meters, standard Φ3.5 three-pin plug outpu.
  • Non-linearity ± 3% (10% ~ 120% rated input current) two output forms of current and voltage (voltage output type built-in sampling resistor)..
  • Package Include 4Pcs x SCT-013-000 Split Core Current Transformer Sensor.
Check Stock

Mini Mounted Point Set, 50 pcs.

  • The transformer has over current, over voltage, over heat protection.
  • With a drill bit, it becomes a hand drill, with a grinding wheel, it becomes a hand grinder, and with a milling cutter, it becomes a hand mill, very easy to use.
  • Wide application range and flexible to operate.
  • The handheld machine has seven standard grinding tools which is varied.
  • Suitable for processing wood, engineering plastics and soft metals.
Check Stock

ACEIRMC 8pcs HX711 Weighing Sensor Dual-Channel 24 Bit Precision A/D Module Pressure Sensor for Arduino Raspberry Pi Microcontroller

  • Analog Current Meter Module. Transformer can only sense AC.
  • This electricity sensor is based on TA12-100 current transformer, which can transform AC signals of large current into small amplitude signals..
  • 3-wire electronic block interface, input 5V - GND. S pin is the output analog voltage value..
  • You can use jumpers to select the parallel output of the output to adjust the range of analog values that are output..
  • On-board 3P and 4P connecting interface for current signal output can be easily connected with your MCU development board.
Check Stock

AC Current Sensor Transformer, PZCT-02 Split Core Current Transformer Coil Sensor for 100A Amp Energy Meter Used for Energy Meter in Special,Current Sensors

  • ❤Specification❤Opening size: 13mm × 13mm.
  • lead length: 1.5 meters, standard Φ3.5 three-pin plug outpu.
  • ❤Applications❤Suitable for current measuring, monitoring and protection of AC motors, lighting equipment, air compressors, etc..
  • ❤Reliability❤Fully compatible with most similar products.
  • the number of opening and closing times is not less than 1000 (tested at 20℃).
  • this split core current transformer is particularly suitable which can use for a long time for DIY use and it works well with arduino and raspberry pi..
  • Non-linearity ± 3% (10% ~ 120% rated input current) two output forms of current and voltage (voltage output type built-in sampling resistor)..
  • Package Include 2Pcs x SCT-013-000 Split Core Current Transformer Sensor.
Check Stock

PEACEFAIR PZCT-02 Split Core Current Transformer Coil Sensor for 100A Amp Energy Meter

  • SMALL AND LIGHT: This current transformer Built-in input coil.
  • SNAP JOINT STRUCTURE:The diameter of inner hole is 16mm, the accuracy is 0.5 grade, Using snap joint structure, it can be fixed to the cable directly through nylon ties..
  • GOOD MECHANICAL PROPERTIES: Fully enclosed, good mechanical properties and environmental resistance, strong voltage isolation capability, safety and reliability..
  • USED FOR ENERGY METER IN SPECIAL: Current transducer used for energy meter in special.
  • AC 220v, 380v power supply can both be applied..
  • MINI SIZE:This is a mini split base current transformer.
  • it's the smallest one compared to the similar products (output 100MA)..
Check Stock

Beleeb 20Amp Variable Transformer Auto AC Voltage Regulator Power Supply, 2000VA Max, 0~130 Volt Output

  • a variable AC input to a transformer input DC bridge rectifier to produce a variable output.
  • The adjustable voltage transformers does not convert AC to DC. It requires an AC input and the output is also AC. Also, the unit will not affect the cycle rate from the power company. If your power system is providing 60Hz, the Variac auto transformer will not change that, the ouput will be an undistorted 60Hz. This unit is rated up to 20 Amps or 2KVA Peak (16A Continous)..
  • Power: 2000VA,Input voltage: 110V, Input current: 18A, Output voltage: 0-130V, Rated output current: 15.38A (Continuous operation for 2 hours, 003c10A can work continuously.
  • This variable transformer is the perfect speed controller. The speed is infinitely variable, and because a transformer doesn't chop up the AC waveform like electronic speed controllers do, there's no noise, humming, etc..
  • If you're planning on using this as an "industrial" or bench-top supply with heavy loads, I'd recommend examining the brushes and adjusting the spring pressure on the windings. This can improve performance by reducing brush-contact sparking. Otherwise, this device is ready to work right out of the box..
Check Stock