Best Poe Optimization

XM1000pro

  • 【PoE & IP OVER COAX CONVERTER】LINOVISION’s POE IP Over Coax converter can be used to upgrade analog system to IP surveillance system while using existing coaxial cable. Compatible with RG59, RG6 cables. Supports POE standards 802.3af (PoE) and 802.3at (PoE+). EOC Receiver should be powered by POE switch or POE injector while Transmitter should be connected with POE devices or NON-POE devices.
  • 【LONG REACH POE TRANSMISSION】Up to 100Mbps in 300m (1000ft) RG59 cable transmission, max 1000m (3000ft) distance in 10Mbps, working with CCA/CCU RG59/RG6 cable. Support POE power transmission with load capacity 11W over 300m (1000ft) transmission, working with POE IP camera, VoIP phone, POE WiFi AP.
  • 【INDUSTRIAL DESIGN WITH BUILT-IN HEAT SINK】Industrial design, with built-in heat sink, ensure super reliability and hassle free transmission. Indoor use ONLY. Plug-and-play, configuration free, makes installation simplest. Small design (3.1"x2.0"x0.9") and light weight.
  • 【POINT TO POINT CONNECTION ONLY】Act as MoCA (Multimedia over Coax) in point-to-point connection, transmit video/audio/data/control signal over coaxial cable.
  • 【WORRY FREE】1 year warranty, US local technical support + Global after-hour support..
Check Stock

Goalake 6 Port Gigabit Ethernet Unmanaged PoE+ Switch, 4 Gigabit PoE+ @52W Built-in Power, 1 Gigabit Uplink + 1 Gigabit SFP Slot, 802.3af/at, VLAN Mode, 4kV Lightning Protection, AI Detection

  • 【VLAN mode 】VLAN mode(Turn on the VLAN switch) support isolate 4 PoE+ port from each other. It is easy for this 4 port PoE switch to manage and maintain ,Prevent broadcast storms, Prevent data confusion, Wireless networking application data is more stable..
  • 【Active poe switch with 802.3af/at compliant】Goalake poe switches support poe devices and non-poe devices, But when connecting passive poe device or non-poe device,the switch can only transmit data and cannot power your device,so the connected device needs to be separately powered. Or you can use it with active poe splitter..
  • 【4 gigabit poe switch@52W 】PoE switch with 4 1000M PoE port + 1 1000M Uplink port,1 x 1G SFP,4×PoE ports providing up to 30W per port, total PoE budget 52W.1 gigabit ethernet Uplink Port for connecting NVR and Internet , etc...
  • 【4KV Lightning Protection】Goalake PoE switch have professional lightning protection design-up 4KV port and power supply thunder prevents, with two levels of protection design respectively, effectively restrain the power of lightning from cable, which equivalent to give the entire network monitoring system with a security fence..
  • 【AI Watchdog function of poe port】When the data or electrical transmission between the poe port and the term....
Check Stock

TRENDnet Powerline 500 AV Nano Adapter Kit, Includes 2 x TPL-406E Adapters, Cross Compatible With Powerline 600-500-200, Windows 10, 8.1, 8, 7, Vista, XP, Plug & Play Install, White, TPL-406E2K

  • GIGABIT PORTS: 1 x Gigabit Ethernet port and 1 x PoE+ Gigabit Ethernet port. Integrated power supply..
  • PoE POWER SUPPLY: This gigabit PoE+ injector supplies a PoE device with PoE (15.4W) or PoE+ (30W) power..
  • INSTALLATION FLEXIBILITY: This PoE+ injector has a wall-mountable design that accommodates most installations scenarios..
  • GIGABIT SPEEDS: Full Duplex 2Gbps Ethernet speeds with this PoE+ injector..
  • PoE DISTANCE: This Gigabit PoE Injector provides a PoE+ network connection up to 100 meters (328 ft.).
  • AUTO SENSING TECHNOLOGY: Auto-sensing technology delivers up to 30W to an 802.3at PoE+ device with backwards compatibility for 802.3af PoE (15.4W) devices..
Check Stock

【Upgraded】LINOVISION POE Over Coax EOC Converter IP Over Coax Max 3000ft Power and Data Transmission Over Regular RG59 Coaxial Cable for Upgrading Analog Surveillance System to IP Surveillance System

  • 【PoE & IP OVER COAX CONVERTER】LINOVISION’s POE IP Over Coax converter can be used to upgrade analog system to IP surveillance system while using existing coaxial cable. Compatible with RG59, RG6, RG11 cables. Supports POE standards 802.3af (PoE) and 802.3at (PoE+). EOC Receiver MUST be powered by POE switch or POE injector while Transmitter should be connected with POE devices or NON-POE devices.
  • 【POE & IP OVER TWIST PAIR CONVERTER】 Each pair of EOC(Ethernet over Coax) Converter is equipped with 2 BNC to Twist Pair connectors, which enables POE over Twist Pair transmission. 100Mbps bandwidth over 330ft regular twist pair cables while 10Mbps over 1485ft for both POE or NON-POE devices. It’s ideal for the CCTV system in elevator cart..
  • 【INDUSTRIAL DESIGN WITH BUILT-IN HEAT SINK】Industrial design, with built-in heat sink, ensure super reliability and hassle free transmission. Indoor use ONLY. Plug-and-play, configuration free, makes installation simplest. Small design (3.1"x2.0"x0.9") and light weight..
  • 【POINT TO POINT CONNECTION ONLY】Act as MoCA (Multimedia over Coax) in point-to-poi....
Check Stock

Ueevii 5.8G Point to Point Wireless Bridge CPE451&2 * 1-Pack Wireless Bridge Bracket Mount 360°Adjustment

  • ...est network speed that can be reached is 100Mbps.
  • Stainless steel material: The bracket is made of high-quality stainless steel, which has the characteristics of strong and sturdy, corrosion resistance, high temperature resistance, waterproof and lightning protection.
  • The CPE451 WiFi bridge has made in-depth protocol optimization for wireless video surveillance transmission, ensuring high-speed video transmission. At the same time, the bottom wireless driver is deeply optimized, with stronger anti-interference ability and better stability..
  • 360°adjustment: There are many small holes on the wireless bridge bracket plate, you can adjust it for 360°, which can easily meet your installation needs at any angle.
  • CPE451 point to point bridge adopts low power consumption, high-performance design, radio frequency index and radiation index are in full compliance with national standards. It supports dynamic MIMO power saving mode (DMPS) and automatic power-saving transmission (APSD) to reduce equipment energy consumption..
Check Stock

TRENDnet 65W 4-Port Gigabit PoE+ Injector, TPE-147GI, 4 x Gigabit Ports(Data in), 4 x gigabit PoE Ports(Data + PoE Out), Multi-Port PoE+ Injector up to 100m(328 ft.), Add PoE+ Power to Non-PoE Switch

  • GIGABIT PORTS 4 x gigabit ports (data in) and 4 x gigabit PoE ports (data + PoE out).
  • EASY INSTALLATION No configuration needed simply connect a PoE network devices to this 4-port PoE+ injector.
  • 4-PORT POE TRENDnet’s 65W 4-Port Gigabit PoE+ Injector supplies up to 30W of power to four PoE (IEEE 802 3af) or PoE+ (IEEE 802 3at) devices at industry PoE standards for greater device interoperability.
  • POE DISTANCE The multi-port gigabit PoE+ injector provides four PoE network connections up to 100m (328 ft ) away from the 4-port PoE injector.
  • FANLESS DISTANCE The fanless design of the gigabit PoE+ Injector eliminates operating noise and lowers energy consumption.
Check Stock

YIDUOYUNCAI 11Port PoE Switch,8 Port 100Mbps PoE+2*1000Mbps Uplink Port and1Gigabit SFP Slot,150W,802.3af/at,Metal Fanless,Unmanaged Plug and Play

  • 【11port poe switch@150W 】PoE switch with 8 100M port PoE + 2 1000M Uplink port+ 1 SFP port, 8×PoE ports providing up to 30W per port, total PoE budget 150W, 2 gigabit ethernet Uplink Port for connecting NVR and Internet , etc..the SFP slot can choose the optcial model with 2km,10km,20km,40km...etc..
  • 【Active poe switch with 802.3af/at compliant】poe switches support poe devices and non-poe devices, but when connecting passive poe device or non-poe device, the switch can only transmit data and cannot power your device, so the connected device needs to be separately powered. Or you can use it with active poe splitter..
  • 【AI PD Detection】The poe port will intelligently judge whether the device connected to the port needs power supply. If it is a non-poe device that does not need power supply, the switch will not supply power to these devices and will not damage the device..
  • 【Built-in power supply】The power supply is located in the poe switch body and integrated with the switch. It is simple and light. After connecting to our AC Power Cable, the switch can transmit power to the equipment connected to the switch..
  • 【Plug and Play】Easy setup with no software installation or configuration needed.
  • 【Network cable short-circuit protection mechani....
Check Stock

YIDUOYUNCAI 6 Port PoE Switch (4*100Mbps PoE Port+2*100Mbps Uplink Port),78W,802.3af/at,VLAN,Metal Fanless,Unmanaged Plug and Play

  • 【6 Port PoE+ Switch】4*10/100Mbps PoE+ Ports(802.3at/af)&2*10/100Mbps uplink, power budget up to 30W per PoE port and 78W for the whole..
  • 【Extend Mode】When Extend Mode is enabled, the transmission distance of POE ports can be extended to 250m at transaction rate of 10M..
  • 【Active poe switch with 802.3af/at compliant】Poe switches support poe devices and non-poe devices, But when connecting passive poe device or non-poe device,the switch can only transmit data and cannot power your device,so the connected device needs to be separately powered. Or you can use it with active poe splitter..
  • 【AI PD Detection】The poe port will intelligently judge whether the device connected to the port needs power supply. If it is a non-poe device that does not need power supply, the switch will not supply power to these devices and will not damage the device..
  • 【Plug and Play】6 Port Unmanaged Network Switch Support automatically detect devices,easy to setup with no software installation or configuration required..
  • 【Fanless design】The fanless design makes poe switch work without any noise..
  • 【Network cable short-circuit protection mechanism】POE switch is stable and has strong anti-interference ability, protect the fault caused by the short circuit of the ....
Check Stock

TRENDnet Inline PoE Tester, TC-NTP1, Tests 4PPoE, PoE+, PoE & Passive PoE Technology, Wattage, Voltage, Amperage, Polarity, LED Display, Battery-Free, Troubleshoot PoE Issues, IEEE 802.3af/at/bt

  • PORTS: This Inline PoE tester is equipped with 1 x Gigabit port for PSE connection, and 1 x Gigabit port for PoE Device connection.
  • TESTING MODES: The TC-NTP1 supports three testing functions. T-mode allows you to test your PSE device to determine the PoE switch's or injector's supported PoE standards, as well as voltage output. N-mode is used for non-standard passive PoE devices. I-mode is used for PoE inline testing, which displays the voltage, amperage, and wattage of the connected PD.
  • USER FRIENDLY: The TC-NTP1 PoE cable tester provides battery-free operation, and is ready for use right out of the box.
  • COMPATABILITY: The PoE cable tester is compatible with IEEE 802.3af/at/bt PoE devices up to 100W, and non-standard passive PoE devices from 11V – 60V..
  • STEP BUTTON: The convenient step button on the PoE cable tester allows users to cycle through voltage, amperage, and wattage readouts. It also allows users to lock the display to a specific readout (e.g. wattage) for real-time monitoring..
  • TROUBLESHOOT IN REAL TIME: Troubleshoot PoE issues in real-time on-the-go and accurately test 4PPoE, PoE+, PoE, and passive PoE technologies with this compact and lightweight PoE testing tool..
Check Stock