Best Neo 6m Gps Arduino

GPS Module Receiver,Navigation Satellite Positioning NEO-6M Arduino GPS Drone Microcontroller GPS Receiver Compatible with 51 Microcontroller STM32 Arduino UNO R3 with Antenna High Sensitivity

With a USB interface, you can directly use the phone data cable on the computer point of view positioning effect.
GT-U7 main module GPS module using the original UBLOX 7th generation chip, Software is compatible with NEO-6M. GT-U7 module, with high sensitivity,....
USB directly connected to the computer, That is, with the host computer-owned serial port function, no need for external serial module, send IPX....
If you have any issue when using our product,or you need product use documentation, please contact us directly for assistance.we will reply your....

IPEX antenna interface，Default distribution：Active antennas，5 DuPont lines.
GT-U7 module with high sensitivity, low power consumption, miniaturization and high tracking sensitivity, the coverage of positioning is greatly....
GT-U7 main module GPS module using the original UBLOX 7th generation chip, compatible with NEO-6M.USB interface, can be connected to the computer,....
Applications: Vehicle handheld devices such as PDA, vehicle monitoring phones, sharing bikes, sharing mobile power, cameras and other mobile....
Quality after-sales service, any problems with the product, we will quickly solve for you after receiving your email.

When you test the GPS module, pls kindly note that you need test it in outdoor wide plain place, not indoor..
The 6M GPS module with ceramic destined antenna, super signal,can be quickly positioned..
The 6M GPS module uses serial comms to the host. It is setup to use 9600baud by default..
LED signal indicator,With data backup battery..
EEPROM power down to save the configuration parameters data..

GT-U7 main module GPS module using the original 7th generation chip, Software is compatible with NEO -6M..
With a USB interface, you can directly connect it with computer. That is, with the host computer-owned serial port function, no need for external....
GT-U7 module, with high sensitivity, low power consumption, miniaturization, its extremely high tracking sensitivity greatly expanded its positioning....
Operating voltage: 3.6V-5V (or direct usb power supply).
Operating baud rate: 9600 (can be modified).
Mobile phones, camcorders and other mobile....

A plug 'n' play shield for experimenting with monitoring fleets, high-altitude measurements, or any kind of project requiring localization of devices..
Arduino MKR GPS Shield uses the u-blox SAM-M8Q GNSS (Global Navigation Satellite System) module. It is meant to be used on top of boards in the Arduino MKR boards, but thanks to its Eslov connector, it is also possible to hook it up to any board..
It comes with a dedicated library that allows two different interfaces and offers a consistent set of APIs designed for a full usage of the GPS acquired information..
Operating voltage is 3.3V, but this shield comes also with an on-board holder for CR1216 batteries..
The MKR GPS Shield has an additional connector meant as an extension of the I2C bus. The extra I2C port, also referred to as the Eslov self-identification port comes with: SDA, SCL, GND, +5V, and an extra digital pin, meant to send an alarm to the otherwise plain I2C devices connected to it..

GT-U7 main module GPS module using the original UBLOX 7th generation chip, Software is compatible with NEO-6M. GT-U7 module, with high sensitivity, low power consumption, miniaturization, its extremely high tracking sensitivity greatly expanded its positioning of the coverage.
With a USB interface, you can directly use the phone data cable on the computer point of view positioning effect.
With IPEX antenna interface, the default distribution of active antenna, can be quickly positioned.
USB directly connected to the computer, That is, with the host computer-owned serial port function, no need for external serial module, send IPX interface active antenna.
If you have any issue when using our product,or you need product use documentation, please contact us directly for assistance.we will reply your problem in 24 hours.We try our best to provide the most professional service for each customer..

Operates on LTE CAT-M1 and/or NB-IoT technology + GPS + temperature sensor.
Directly compatible with Arduino Uno, Mega, and Leonardo + easy connection for other logic voltages.
Ultra low-power mode drawing < 8uA, ideal for battery-powered IoT devices + LiPo battery charging.
Kit includes dual flexible LTE/GPS antenna and stacking female header kit.
Detailed documentation, wiki, Arduino library, and code examples on Github + community forum to ask questions.

PERFECT COMPATIBLITY - Perfectly designed for your precious Bushnell Neo Ion 1, Ion 2, Excel Golf GPS Smartwatch. Note: Bushnell Neo Ion 1, Ion 2,....
HIGH PROTECTION - Provide short-circuit protection and overcurrent protection that prevent your Bushnell Neo Ion 1, Ion 2, Excel Golf GPS Smartwatch....
PREMIUM QUALITY - Adopted imported material, the flexible cable ensures tangle-free operation. Premium PVC materials with a smooth surface protect....
LONG SERVICE LIFE - The working current is stable, and the temperature is kept constantly during charging, so as to protect the watch..
PORTABLE - Compact and lightweight design makes it easy to store and carry. Convenient to use in Office, at home or on travels! We advise that you....