Best Multiplexer Channel

10 PCS Analog Multiplexer,Breakout Board Module,CD74HC4067 High Speed CMOS 16-Channel Analog Digital Multiplexer Demultiplexer,Suitable for Digital and Analog Signals

Because the multiplexer can also process digital signals, you can use it to transfer TTL-level serial data to multiple devices through pipe or transfer from multiple devices..
It is suitable for digital and analog signals (voltage cannot be higher than VCC) and can be connected in either direction. To control this, please connect the four digital outputs to the address selection pin of the chip (SO-S3) and send it the binary address of the desired channel..
This is a very convenient 16 channel CD74HC4067 analog/digital multiplexer/demultiplexer..
The internal switch is bidirectional, with a low on resistance and off leakage, and to prevent talk, please turn off the switch first and then on..
Drive it to a high level, and it will completely disconnect the common pins (all switches are disconnected)..

The TCA9548A adapter is connected to an I2C device with multiple identical addresses on the same I2C port on the main control board for normal communication and use.There are 8 I2C interfaces on one expander, and there are eight bidirectional transfer switches that can be controlled by I2C bus. This means that after 1 expander is transferred, 8 identical addresses can be connected to the same I2C port..
Expansion board TCA9548A compatible with IIC bus and system management bus (SMBus), active low reset input, support for hot insertion, low standby current, no glitch during power-up, support for voltages between 1.8V, 2.5V, 3.3V and 5V buses Level shifting, TCA9548A I2C IIC multiplexer breakout board depending on the contents of the programmable control registers, any single SCn/SDn channel or combination of channels can be selected..
12pcs TCA9548A I2C IIC Multiplexer Breakout Board 8 Channel Expansion Board for Arduino.

Function: Use 16 ADCs to collect 16 analog signals.003cbr003e.
Use the CD74HC4067 16-channel analog signal switch.
Analog signal input: C0-C15 16 channels.003cbr003e.
This is a breakout board for the very handy 16-Channel Analog / Digital Multiplexer / Demultiplexer CD74HC4067.003cbr003e.
This chip is like a rotary switch - it internally routes the common pin (COM in the schematic, SIG on the board) to one of 16 channel pins (CHANxx). It works with both digital and analog signals (the voltage can't be higher than VCC), and the connections function in either direction.003cbr003e.

Function: Use 16 ADCs to collect 16 analog signals..
Use the CD74HC4067 16-channel analog signal switch.
Analog signal input: C0-C15 16 channels..
This is a breakout board for the very handy 16-Channel Analog/Digital Multiplexer/Demultiplexer CD74HC4067..
This chip is like a rotary switch - it internally routes the common pin (COM in the schematic, SIG on the board) to one of 16 channel pins (CHANxx). It works with both digital and analog signals (the voltage can't be higher than VCC), and the connections function in either direction..

The TCA9548A Breakout board supports communicating with multiple I2C devices with the same address, making it easy to interface with them..
TCA9548A multiplexer features: bidirectional eight-channel I2C multiplexer, active low reset input.
The default address of this expander is 0x70, the address can be changed, and can be set within 0x70~0x77..
In the address of 0x70~0x77, 8 expanders can be cascaded, and each expander can be connected to 8 devices with the same address, so that the same I2C port can be connected to 64 devices with the same address and can be used normally..
The chip is compatible with 3V and 5V and can be used with any logic level.

Full quad display at real-tme refresh rate.
Camera title, time and date display for easy identification, 4 Channel BNC input and 2 Video BNC outputs.
Free 1A Power Adapter and remote control Included.

Advanced 16-channel video multiplexer mixer for real-time multi-channel display on one screen. Full duplex operation for displaying and recording all of its video channels simultaneously..
Ideal for security monitoring or video preview application where multiple images are needed. Split-screen modes and PIP locations can be manually configured with ease by the front panel, IR remote or RS232 console..
16 individual input buttons for fast switching between each video input. 16 video pass-through ports. 3 video outputs including 2 composite BNC/RCA video outputs and 1 VGA out at 1024x768 for live viewing and recording..
4 audio inputs with 1 audio output. 16 screen mode options presented in 16/9/8/4/3-grid, quad screen, PIP, picture-by-picture style or single channel full screen. Easy selection for main channel, sub/PIP channel via front push buttons or IR remote for best suited visual presentation..
Supports RS232 long range control and camera control by RS485 connection. Supports time/date stamp and auto sequential switching function with adjustable dwelling time..

16 Camera Inputs - Supports up to 16 Analog cameras via the 16 BNC video inputs..
16 Camera Outputs - 16 BNC video loopouts allow each camera to be connected to additional devices such as DVRs or VCRs..
Supports PTZ Cameras - The RS-485 terminals can control the motions of pan, tilt, and zoom (PTZ) cameras..
Rackmountable Case - The 1U rackmount case gives users the option to mount it in a standard 19 inch server rack..
Multiple Viewing Modes - This video multiplexer supports multiple camera grid displays including a 16 channel, 8 channel, 4 channel, 1 channel, PIP, and more..