Best Motor Driver With Spi

DIYmall Mini PiTFT 1.3″ LCD Display 240×240 TFT Add-on for Raspberry Pi 3.3V SPI ST7789 3.3V SPI ST7789 Full Color

TFT size： 1.3″ diagonal, Voltage：3.3V, Interface：SPI, Driver: ST7789, Color：Full color.
The Mini Pi TFT 1.3 ” – 240×240 Color TFT Add-on for Raspberry Pi is your little TFT pal, ready to snap onto any and all Raspberry Pi , to give you a little display..
The Mini Pi TFT comes with a full color 240×240 pixel IPS display with great visibility at all angles..
The TFT uses only the SPI port so its very fast, and we leave plenty of pins remaining available for buttons, LEDs, sensors, etc. It’s also nice and compact so it will fit into any case..

Screen connect with SPI directly, Support FBCP software drive, support double screen display, can ajdust the resolution of the software to zoom.
Physical resolution 320x480 with resistive touch control, can be directly connect Raspberry Pi 3 B+ , No additional Power. (Raspberry Pi is not included).
The screen Display support 125MHz SPI signal input, it can display stable without flicker, the refresh rate is about 50fps, it’s enough to play the video and game..
Support work with Raspbian/Ubuntu/Kali/Retropie systems. We offer pre-install driver system image file..
Match PC Protective Case for your screen and Pi, use split design make it easy to install, also match tweezers to make install more easy. White nylon column can help screen maintain balance..

This Motor Driver HAT gives your Raspberry Pi the ability to drive two DC motors, with drive current up to 2A..
Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards like Raspberry Pi Zero/Zero W/Zero WH/2B/3B/3B+/4B and later versions.
Reserved I2C SPI control pins, allows to work with other control boards and sensors. Comes with an IR receiver for communication with an infrared remote controller..
Included 4x M2.5*20MM screws, 4 xM2.5*10MM copper pillars, 4x M2.5 Nuts. Easy to install on your RPi board. Please note Raspberry Pi board, remote control and motors in the photos are Not Included!.

TFT size： 1.3″ diagonal, Voltage：3.3V, Interface：SPI, Driver: ST7789, Color：Full color.
The Mini Pi TFT 1.3 ” – 240×240 Color TFT Add-on for Raspberry Pi is your little TFT pal, ready to snap onto any and all Raspberry Pi , to give you a little display..
The Mini Pi TFT comes with a full color 240×240 pixel IPS display with great visibility at all angles..
The TFT uses only the SPI port so its very fast, and we leave plenty of pins remaining available for buttons, LEDs, sensors, etc. It’s also nice and compact so it will fit into any case..

【Brussless Spindle Motor】Power: 400W.
Note: Please see clearly that this spindle motor output shaft is with ER8 collet,and output shaft is complete shaft, can't be exchanged to ER11, ER16....
【Brussless Spindle Motor Driver】Maximum driver power: 600W.
Maximum driver motor running speed: 12000R/Min.
Brushless spindle driver（Model Name: NVBDL）is specialized for the ecomomic engraving machine,it matchs with the brushless DC motor. With the....
The users can take down the panel from the main driver and install it on the controller cabinet.By the panel,you can set the parameter,control motor....

This is a new 2.8 inch serial SPI color display module with touch function.
Designed with one socket for memory card.
With PCB plate (including power supply IC, Memory Card), compatible with 5110 interface.
5V compatible, use with 3.3V or 5V logic.

The BME280 sensor is a precision sensor, is soldered onto PCB, not only the pressure and the temperature, this sensor can measure humidity..
BME280 5V uses both I2C and SPI (supports 3-, 4-wire SPI) interface. Interface: I2C (up to 3.4MHz).
Temperature humidity module is great for all sorts of weather sensing and can even be used in both I2C and SPI. for simple easy wiring, go with I2C. If you want to connect a bunch of sensors without worrying about I2C address collisions, go with SPI..
The BME280 stmospheric pressure sensor is made up of a very accurate pressure sensor and an associated temperature sensor which helps calibrate the pressure readings..
The BME280 sensor is precision sensing solution for measuring barometric pressure with ±1 hPa absolute accuraccy, and temperature with ±1.0°C accuracy. Because pressure changes with altitude, and the pressure measurements are good, you can also use it as an altimeter with ±1 meter accuracy..