Best Mmdvm Hotspot Duplex

MMDVM Hotspot Spot Assembled Radio Station OLED Antenna WiFi Digital Voice Modem P25 DMR YSF C4FM Raspberry Pie Pi

  • MMDVM hotspot supports D-STAR DMR YSF P25 NXDN POCSAG, enables the different mode of digital two way radio to communicate with each other (YSF2DMR / YSF2NXDN / YSF2P25 / DMR2YSF / DMR2NXDN) and works great with UHF..
  • Setup: Set the same freq as Radio Mobile, for example: 433.550000MHZ. DMR WIFI SSID:pi-star,PASSWORD:raspberry. Need the 2.4GHz SSID as the Pi Zero W. doesn't support 5.8GHz.
  • Power Supply: Mobile charger or a USB cable connected to your computer or laptop..
  • Best customer services: fully-assembled. The firmware is pre-loaded. Contact us if any question, we will reply within 6 hours. 73.
Check Stock

MMDVM Duplex Hotspot Module Dual Hat V1.3 Support P25 DMR YSF NXDN DMR Slot 1 + Slot 2 for Raspberry pi with USB Port (Without OLED)

  • if the board fails to work on duplex mode, please run the upgrade command: sudo pistar-mmdvmhshatflash hs_dual_hat.
  • HIGH PERFORMACE: 32-bit ARM processor, up to 10mW RF power, fully tested every piece..
  • WIDELY COMPATIBLE: Supports DMR, P-25, D-Star and System Fusion.
  • WORK with RASBERRY Pi: Mounts cleanly on current Raspberry Pi including the Pi Zero , NOT compatible with Rasberry Pi 4..
  • Update new FW: (pi-star / expert / ssh access / user :pi-star pass:raspberry) then run sudo pistar-mmdvmhshatflash hs_dual_hat set Jumper BOOT0=1,BOOT1=0 and soler JP1 First! After upgraded finished, disconnect JP1.
  • FREQUENCY: Radio Frequency : Freq:144-148,219-225, (Main Band) 420-475,842-950 NOTE: TX =0, RX=0. Modem select: STM32-DVM/MMDVM_HS-Raspberry pi Hat(GPIO) or any other (GPIO board).
Check Stock

MMDVM Duplex Hotspot Module Dual Hat with 0.96 OLED Display V1.47 Support P25 DMR YSF NXDN DMR Slot 1 + Slot 2 for Raspberry pi (with OLED)

  • if the board fails to work on duplex mode, please run the upgrade command: sudo pistar-mmdvmhshatflash hs_dual_hat.
  • HIGH PERFORMACE: 32-bit ARM processor, up to 10mW RF power, fully tested every piece..
  • WIDELY COMPATIBLE: Supports DMR, P-25, D-Star and System Fusion.
  • WORK with RASBERRY Pi: Mounts cleanly on current Raspberry Pi including the Pi Zero , NOT compatible with Rasberry Pi 4..
  • EASY OPERATION: The firmware is pre-loaded and is easily upgraded via software. Onboard LEDs showing status (Tx,Rx,PTT,Mode).
  • FREQUENCY: UHF 433-900MHz, VHF 144-220 MHz. NOTE: TX =0, RX=0. Modem select: STM32_HS_GPIO.
  • To leave the screen on all the time In Pi-Star configuration, ensure you have "OLED Type 3" in the display type field at the top of the page, set Port to: modem. Also, in the Expert section, go to MMDVM host, and scroll down to the OLED section. Make sure LogoScreensaver is set to 1. This leaves the screen on all the time. Otherwise, it goes blank when idle.
Check Stock

Hima MMDVM Hotspot Spot Radio Station+ Antenna + OLED with Screen Support P25 DMR YSF D-Star UHF Expansion Board WiFi Digital Voice Modem Suitable for Raspberry Pi-Zero W, Pi 3, Pi 3B+

  • The kit includes: high performance with screen ARM processor, SMA antenna connector, including antenna, 2 pins, 4 screws..
  • Support:D-STAR, P25, DMR and work with UHF.Software:Pi-Star,Suit for Raspberry Pi 3,Raspberry PI-Zero w, Raspberry Pi 3b+.The 40pin raspberry pie needs to insulate the middle 20pin pin headers for normal use..
  • Power supply: USB cable connected to your computer or laptop. The Hotspot will also work mobile in your vehicle if you Tether it to your mobile phone network..
  • Basic Setup: 433.550000MHZ DMR (Need the 2.4GHz SSID as the Pi W doesn't support 5.8GHz)..
  • Note: All designs will be contributed on MMDVM open source project.If you encounter a different version of pi zero not work, please see the picture instructions. If you have any difficult， please contact us to help you solve the problem..
Check Stock

NetAlly LSPRNTR-300 LinkSprinter 300 Network Tester with WiFi and Distance to Cable Fault Indication, w/WiFi & Distance to Cable Fault Indication

  • Discover the nearest switch name and port information via CDP/LLDP/EDP, and verify link speed/duplex and connectivity to TCP/IP networks..
  • Validate Power-over-Ethernet (PoE) voltage from power sourcing equipment (PSE) according to 802. 3af/at standards..
  • View detailed test results, add comments, and run cable tests using your mobile device over a Wi-Fi hotspot built into the LinkSprinter..
  • Automate reporting and enable collaboration with test results upload and management via Link-Live Cloud Service..
Check Stock

C4Labs JRZ-1SB case Compatible with Raspberry Pi Zero/Zero W & JumboSPOT MMDVM & Waveshare UPS Hat (Black Ice)

  • Full body coverage for Raspberry Pi, Battery Hat, JumboSPOT or LoneStar N5BOC MMDVM Simplex and OLED screen (not waterproof) Note: Raspberry Pi Zero 2 has not been tested for heat issues..
  • Enough room for .96″ OLED screen to be mounted directly to JumboSPOT or LoneStar N5BOC MMDVM Simplex by customer.
  • Cut outs for easy access to SD card and camera ports.
  • Pin-hole access to boot and reset buttons on top of case.
  • No components are included. This is a Case Kit and assembly is required..
  • Designed and Crafted by local artists in Tacoma, WA USA.
  • Comes with 2 tops: one with antenna hole and one without.
  • Compatible with Lonestar N5BOC Board version 03/23/2019 1V8-1.
Check Stock

Duplex MMDVM Hotspot Radio Station P25 DMR Hotspot Antenna WiFi Digital Voice Modem Support YSF Raspberry Pi Zero

  • Suit for Raspberry Pi Zero W. Support:DMR,D-STAR, P25 and work with UHF in duplex mode. In Simplex mode support both Uhf and Vhf.
  • Basic Setup: Set the same freq as Radio Mobile, for example: 433.550000MHZ DMR, WIFI SSID:pi-star,PASSWORD:raspberry, Need the 2.4GHz SSID as the Pi Zero W doesn't support 5.8GHz.
  • Power Supply: Mobile charger or a USB cable connected to your computer or laptop. The Hotspot will also work mobile in your vehicle if you Tether it to your mobile phone network..
  • Support receive in one Frequency and tranfer in another Frequency..
  • Best customer service: feel free to contact us,we will reply soon within 24 hours..
Check Stock

C4Labs JRPi-3.5NSX Nextion Screen Case for Raspberry Pi 4B & 3B+, Jumbospot MMDVM, and 3.5\ Nextion Screen (Included)

  • If you have a Zumspot Brand MMDVM Board there is a new case model: ZRPI-3.5NSX.
  • For Raspberry Pi 4B, 3B+, 3B, 2B, and B+ (not included), JUMBOspot (a generic Chinese MMDVM board - Not included), and a 3.5″ Enhanced Nextion Touchscreen (included). Carefully designed to precisely fit these components using Laser cut components and stainless steel hardware. Full body coverage for components (not waterproof). Heat sinks and rubber feet included..
  • *Please note that connecting the Nextion screen to your set-up may require additional soldering of pins or wires not covered in these case instructions..
  • Note: This case does not have a fan and the Pi-4 is known to run hot under use. It is not recommended to run the Pi-4 at full power for extended periods as performance problems can arise at higher temperatures.* The new inner layers have been designed to fit the Pimoroni Fan SHIM (not included).
  • Engineered and manufactured with Pride in Tacoma, WA USA.
Check Stock

C4Labs ZRPi-3.5NSX Nextion Screen Case – Raspberry Pi 3 B+, ZUMspot MMDVM, and Enhanced 3.5\ Nextion Screen (Included) ~ Black Ice

  • If you have a Generic Chinese MMDVM Board (Jumbospot) there is a new case model: JRPI-3.5NSX.
  • For Raspberry Pi 4B, 3B+, 3B, 2B, and B+ (not included), ZUMspot Brand MMDVM Board (Not included), and a 3.5" Enhanced Nextion Touchscreen (included). Carefully designed to precisely fit these components using Laser cut components and stainless steel hardware. Full body coverage for components (not waterproof). Heat sinks and rubber feet included..
  • *Please note that connecting the Nextion screen to your set-up may require additional soldering of pins or wires not covered in these case instructions..
  • Note: This case does not have a fan and the Pi-4 is known to run hot under use. It is not recommended to run the Pi-4 at full power for extended periods as performance problems can arise at higher temperatures.* The new inner layers have been designed to fit the Pimoroni Fan SHIM (not included).
  • Engineered and manufactured with Pride in Tacoma, WA USA.
Check Stock