Best Mini Angle Gauge

Neiko 20699A 1/2\ Drive Torque Angle Gauge, Clear

Torque angle gauge is used specially for later model engines that require a torque to yield fastener.
Easy to use arm attachment is used for holding the gauge in place for an undisturbed work flow while turn plate makes it easy to zero out the gauge.
360 degree scale is large and easy to read with 30 degree intervals and 10 degree increments.
Specs: the angle gauge has a 1/2 inch male and female square drive ratchet handle.
Gauge measures angle of rotation after pre-torque in torque-angle applications.

Check Stock

GemRed 82412 Mini Digital Level Angle Gauge Angle Finder Protractor Inclinometer Aluminum Framework with Magnet

【Great Repeatability and Consistency】This angle gauge is designed with accuracy of ± 0.2° and the resolution is 0.1°. The measuring range: 0 to 360° (4*90°). Display unit: DEGREE only. It provides convenience in woodworking, construction, machinery, telecommunications, automobile etc. It is pre-calibrated in factory..
【Strong Aluminum Framework&Magnetic Flat Base】The digital angle gauge applied sturdy aluminum alloy instead of plastic for the main framework. It’ll provide years’ usage.【Two Measuring Mode】①Checking the true level. ②Checking the relative angle between two surfaces..
【Lower Power Reversible LCD Display with ERROR indicator】 The Digital Angle Gauge has a large LCD display with backlight, which only needs one battery for providing accurate, quick and clear measurements and even you can easily read in dark environment. If the digital angle gauge is used in an incorrect position (e.g. tilts diagonally over 30 degree), display will tell ERROR to make sure that use is getting the accurate measurement..
【Easy Battery Installation】You can install battery easily and need no screwdriver. WIth only one AAA battery, the digital angle gauge works 50 hours averagely. *Automatic shut-off after 5 minutes..

Check Stock

COMeap Motherboard ATX Mini 8 Pin to 2X Right-Angle 15 Pin SATA Hard Drive HDD Power Adapter Cable for Dell OptiPlex Series 3020 5040 7020 9020 14.5-inch(37cm)

『Connectors』Connector A: ATX 12V mini 8 pin (NOTE: not standard 8 pin), Connector B: 2x Right-angle SATA 15 pin (compatible with the equipment with sata port such as: liquid CPU cooler, mechanical hhd and a ssd).
『Parameter』Gauge: 18AWG with braided sleeves for easy cable management, Length(including connectors): 14.5 inches(37cm)，Between 2 SATA: 2.36 inches(6cm).
『Note』This cable was only designed for some types of DELL OptiPlex series as listed. If you connect it with other incompatible motherboards, it will burn or damage the motherboard and we won’t take any responsibility for wrongly using or installing. Please carefully check the compatible types or contact us if you are not sure about it.
『Compatibility』Compatible with DELL OptiPlex series such as 3020/3040/5040/7020/7040/9020 MT, T1700MT.
『Mini 8P – 2x Right-Angle SATA』Mini 8 Pin port plugs into the motherboard (NOTE: It is mini 8 pin port, not standard 8 pin port.), 15 Pin SATA port plugs into the hard drive.

Check Stock

Drill Angle Gauge, 3Pcs Drill Bits Angle Gauge Set Dirll Sharpener Tools S/S Angle Measuring Gage Drill Bit Angle (60 °, 70 °, 90 °, 110 °, 118 °, 125 °, 135 °, 150 °, 160 °)

【Material】: This Angle gauge set is made of high quality stainless steel, high hardness, and durable in use..
【Design】: It is a practical Angle gauge set in drill bits Angle measuring and drill sharpener inspection,and comes with a case, convenient for carrying out..
【Feature】: Diameter drill front edge of the protractor 50 gauge 118 ° apex angle of twist drills grinding gauge suitable for 118 ° apex diameter of not more than 50mm of grinding twist drills..
【Drill Apex Angle】: Check the drill apex angle (60 °, 70 °, 90 °, 110 °, 118 °, 125 °, 135 °, 150 °, 160 °). Cutting tool angle is 60 degrees for a tooth-shaped angle 55 degree angle and metric thread, inch thread inspection, blade and special measuring tools for measuring angles.
【Usage】: Suitable For: Angle measurement.

Check Stock

Angle Gauge Drill Bits, 3Pcs S/S Angle Gauge Measurement Drill Sharpener Tool Set Including Drill Diameter, Drill Bits and General Angle Gauge with Case

Professional Measurement Tool: This is a practical set of angle gauge set in drill bits angle measuring and drill sharpener inspection.
Professional and Standard Parameters: 60 Degree cutting tool for the inspection of tooth‑shaped 55 degree angle and metric thread and inch thread, and also it can measure blade angles.
Comprehensive Angle Range: This set of drill bits gauge has a comprehensive angle range: 60 °, 70 °, 90 °, 110 °, 118 °, 125 °, 135 °, 150 ° and 160 °.
Suitable Utilization: Diameter drill front edge of the protractor 50 gauge 118 ° angle twist drills grinding gauge is suitable for 118 ° diameter of less than 50mm grinding twist drills.
Durable for Long-Time Use: Made of high quality stainless steel, this set of angle gauge has high hardness, and it is durable for long-time use.

Check Stock

Proster 200mm 360°Angle Finder Data Hold LCD Angle Ruler One Key Zeroing 80mm 3 1/8\ Magnetic Height Gauge Depth Gauge for Woodworking Construction Home Decoration

【Accurate Angle Finder】200mm stainless steel ruler to measure length (metric and imperial), 360°angle sensor for relative and absolute angle measurement inside and outside, Range:0-360°,Resolution：0.05°,Accuracy：±0.3°,Repeatability：0.05°..
【One-key Data Hold & Zero Reseting】Knob locked one-key data hold function for both angle/depth gauge to hold the angles/depth measured at any time.
Zeroing reset button at any angle for relative measuring..
【Multi-function Magnetic Height Gauge】3-In-1 Height/Depth/Thickness Gauge,easy to measure bore/slot depths with plunger, one key mm/inch/fraction switch, range: 80mm, resolution: 0.05mm, accuracy: 0.10mm for routers horizontal/vertical measure with self standing magnetic feet..
【LCD Display & Stainless Steel】Sturdy plastic thickness gauge for with quick-reading digital LCD display, harden stainless steel angle finder ruler and depth ruler provides lifelong service..
【Wide Applicatoion】This angle finder with magnetic height depth thickness gauge is especially designed for Woodworking, Construction, Home Decoration, Table saws, Hand Routers, Etc..

Check Stock

Calculated Industries 7489 AccuMASTER Value Pack – 2-in-1 Digital Angle Gauge plus the Digital 7-Inch Angle Finder Ruler | Accurate Precision Tools for Carpenters, Woodworkers, Fabricators | 2-Pieces

VALUE PACK INCLUDES – A precision tools combo of the Digital Angle Finder Ruler and the 2-in-1 Digital Angle Gauge. Perfect for the pro or hobbyist who needs to transfer true level and precise angle settings to their saws.
TOOLS USED TOGETHER – the Angle Finder Ruler enables you to determine the angle of your workpiece that you need to match. The Digital Angle Gauge helps you transfer that angle to your saw or other tool so your finished cut installs perfectly.
DUAL FUNCTIONALITY – Angle Gauge works as an inclinometer or tilt gauge to set or check relative angles between surfaces, also works as digital level for tight spots with bright backlit Stay glow display, strong magnetic base, dust/water resistant.
ANGLE FINDER RULER can be reset to zero at any position for simple relative or differential angle calculations. Large LCD display HOLD lets you freeze a display value. Full-range protractor measures 360° for both inside and outside angles, 7-inch ruler arms.

Check Stock

4 inch Mighty-Mite Table Saw

Miter gauge and two slots for precise angle cutting.
Perfectly cuts picture frames,molding and plastic.
This mini table saw is ideal for small wood projects..

Check Stock

DWE7402DI Dado Throat Plate, Table Saw Parts Insert Accessories Replacement for 10-Inch Portable Table Saw DEWALT DWE7490, DWE7491 Versiones

❤ [A good helper for table saws] If you have a table saw and need to cut at any angle, then you will know the value of a miter gauge. You may also know that the miter gauge that comes with the saw is not very accurate or durable. Not to mention the fit in the miter groove may not be so good. And our high-quality miter gauges can meet your table saw cross-cutting needs..
❤[High-quality material] The guide rod and baffle of the table saw miter gauge are made of all aluminum to ensure its durability and firmness, rust and wear resistance, and the table saw miter gauge fence is made of aluminum alloy die-casting, which has better accuracy. high..
❤[With clamp] The table saw miter gauge is composed of a miter gauge clamp, a material baffle, and an angle push plate. The clamps can be adjusted by screws to fix different cutting objects, which is not possible with other mitre gauges without a holder. The bottom of the mitre gauge is equipped with a 5/8 groove for the mitre gauge, and the all-aluminum slide bar slides smoothly ..
❤ [Easy to operate] The miter gauge is cut at a precise angle of 60° on both sides with pointers. If you need to adjust the head, you only need to loosen the column knob and rotate the head to the desired position, so loosen th....

Check Stock