Best Manifold Bolt Set

Dorman 03107 Front Manifold Stud and Spring Kit - M10-1.5 x 77mm Compatible with Select Chevrolet / GMC / Oldsmobile Models

  • Ideal replacement - the manifold bolt and spring match the fit and function of the original equipment hardware, including bolt diameter, thread pitch and head type.
  • Complete installation - this kit includes hardware required for securely attaching the manifold to the exhaust system.
  • Trustworthy construction - the kit's bolt and spring are made of hardened steel for durable, long-lasting service life.
  • Quality tested - kit components have undergone extensive testing to ensure proper function and long service life.
  • Ensure fit - to make sure this part fits your exact vehicle, input your make, model and trim level into the garage tool.
Check Stock

Dorman 03123 Front Manifold Bolt and Spring Kit - 3/8-16 x 1-3/4; M10-1.25 x 67mm Compatible with Select Toyota Models

  • Ideal replacement - the manifold bolt and spring match the fit and function of the original equipment hardware, including bolt diameter, thread pitch and head type.
  • Complete installation - this kit includes hardware required for securely attaching the manifold to the exhaust system.
  • Trustworthy construction - the kit's bolt and spring are made of hardened steel for durable, long-lasting service life.
  • Quality tested - kit components have undergone extensive testing to ensure proper function and long service life.
  • Ensure fit - to make sure this part fits your exact vehicle, input your make, model and trim level into the garage tool.
Check Stock

E-Tuner 4

  • EFI Fabricated Intake Manifold with Fuel Rails and Throttle Body Short, Silver.
  • Compatible With: Chevrolet Small Block V8 Gen. III/IV (LS-based) · 4.8 L / 293 In3 (L20, Ly2) · 5.3 L / 325 In3 (Lc9, Lh6, Lh8, Lmg, Ly5) · 6.0 L / 364 In3 (L76, L96, LFA, LY6) · 6.2 L / 376 LN3 (L92, L99, LS3, LSA)Rectangle Port Intakes only!.
  • Fabricated Aluminum Sheet Metal Intake Manifold -102MM Throttle Body -Fuel Rails & Cross Over -4-Bolt LSX - Gaskets & Hardware are included..
  • Throttle Body is Dive by Cable Overview We Designed Our Fabricated Aluminum Sheet Metal Intake Manifold to Improve the Look and Performance of Your LS Engine..
Check Stock

Edelbrock 2181 Performer Intake Manifold

  • Delivers improved throttle response over stock intakes and are available in both EGR and non-EGR styles.
  • When using a 12-bolt manifold on 16-bolt heads, 16-bolt intake gasket is used to ensure proper sealing around the water ports on the heads.
  • Factory composition-type embossed gasket also works satisfactorily.
  • Boosts torque over a wide RPM range, from idle to 5, 500 RPM.
Check Stock

Precision 40mm Wastegate Inlet Flange

  • ▶️ High strength cast steel body with steel head.
  • ▶️ Bolt-on design, fits any 40mm turbo manifold bolt-on wastegate port.
  • ▶️ Bolt-on housing design for secure spring changing and adjustment.
  • ▶️ High pressure reinforced and temperature resistant actuator diaphram included.
  • ▶️ Comes with 10 psi spring installed.
Check Stock

A-Team Performance - Hex Flange Bolts LS Exhaust Flange Manifold Header Zinc Plated - Compatible with GM Chevrolet Chevy LS1 LS3 LS2 LSX LT Engines 551696 Bolt Kit Only Silver

  • Hex Flange Bolts LS Exhaust Flange Manifold Header Zinc Plated.
  • Compatible with GM Chevrolet Chevy LS1 LS3 LS2 LSX LT Engines 551696 Bolt Kit Only Silver.
  • GM LS / LT Engines (Gen III, IV, V). USA Grade 10.9 with LS Exhaust Manifold Bolts.
  • Zinc-Plated and 350 Header Gasket Set with Bolts.
Check Stock

Exhaust Manifold Bolt Repair Kit Compatible with 4.8 5.3 5.7 6.0 6.2 LS1 LS2 LS3 LS6 Chevy LSX Camaro, Corvette, Trans am, GTO, G8, CTS V, GM Trucks

  • This Exhaust Manifold Bolt Repair Kit was used to repair Driver's Side Rear and Passenger Side Front. We also selling Driver's Side Front and Passenger Side Rear. You can buy it at my store..
  • The Exhaust Manifold Bolt Repair Bracket will Eliminate exhaust noise and repair the exhaust leak without having to remove the cylinder head or drill out and replace the broken end bolts! Save your time and money..
  • Manufactured from high-quality Steel, TIG welding. For durablity and long service time. Kits comes with necessary block, bolts and washers for solid repair..
  • The Exhaust Manifold Bolt Repair Kit Compatible with L20, L31, L33, L59, L76, L77, L83, L86, L8T,L92, L94, L96, L98, L99, L9H, LC9, LFA, LH6, LH8, LM4, LM7, LMG, LQ4, LQ9, LR4,LS1, LS2, LS3, LS4, LS6, LS7, LS9, LSA, LSX376, LSX454, LSX454R, LT1, LT2, LT4,LT5, LY2, LY5, LY6, LZ1.(Fits for GM Vehicles, Silverado, Sierra, Yukon, Denali, Escalade, Hummer ).
  • If any issues from our products arise please don’t hesitate to contact us. We guarantee the quality of our tools and want to ensure you’re only getting the best. B....
Check Stock

Vinco - Glukokine 60 tabs

  • Fitment: This Exhaust Manifold Bolt Set Compatible with Dakota V8 4.7L Club Cab 2WD 05 06 07 08 09 10 11 , 1500 V8 4.7L Laramie Quad Cab 2WD, Laramie....
  • Interchange/ Part Number: 6505316AA, 6507746AA, 6508219AA, 6508220AA, Specification: Thread Size: M6-1.0, Thread Size: M8-1.25, Material: Steel,....
  • Package included: 4 Studs(2 Long & 2 short), 4 Bolts and 4 Nuts.
  • Engineered from premium materials to provide exceptional service life and reliability.
  • Designed to withstand the harsh conditions in the modern engine compartment.
  • Advanced manufacturing technology ensures durability and optimum operation....
Check Stock

kipa Pressure Washer Manifold Kit for Briggs Stratton 020228 Pressure Washer EXWGV1721, Replace Part 16031 190627GS 190574GS Injector Inlet Valve Mounting Bolt

  • New Pressure Washer Manifold Kit For Briggs Stratton 020228 Pressure washer EXWGV1721, Replace part 16031 190627GS 190574GS injector inlet valve Mounting Bolt.
  • Top Quality CNC-Machined KIPA Pressure Washer Manifold Kit, easy to install. Directly Fit.
  • Fits for Briggs model number 020228. Please do match the part Number and the structure before purchasing, Thanks.
  • Pressure washer model EXWGV1721 -- It includes a shorter extension but if you like. You can remove the short one and install the longer one that is on the OEM manifold.
  • Please note: Please be sure to mount it in the proper direction. If it is mounted backwards, it will blow the casting apart as soon as the engine starts, right where the unloader valve comes out of the manifold.
Check Stock