Best Low voltage Motor Driver

DC Motor Driver, DROK L298 Dual H Bridge Motor Speed Controller DC 6.5V-27V 7A PWM Motor Regulator Board 12V 24V Electric Motor Control Module Industrial 160W with Optocoupler Isolation

DROK DC motor driver input voltage range is DC 6.5V-27V, can be input DC 12V or 24V, rated output current of each port is 7A, total output power is 160W..
STRONG DRIVE: the motor controller board adopts dual H bridge, can drive two DC motors at the same time..
FORWARD and REVSERSELY ROTATE: the IN1, IN2/IN3, IN4 port can control forward or reverse motor rotation..
PWM SPEED CONTROL: enable signal terminal (ENA) input PWM can regulate speed, PWM frequency range 0-10KHZ..
UNDER VOLTAGE PROTECTION: the motor driver module is with under voltage protection to prevent instantaneous large current from damaging the module..

♞【Product】3 Axis nema23 stepper motor driver controller kit.
♞【Application】This cnc kit are widely used in engraving machine, printer,....
♞【Stepper Motor】23HS2430B Nema23 57 stepper motor.
♞【Driver】CW5045 driver Voltage: DC 24-50V.
Current: rated maximum output reaches: ±4.5A.
♞【5 Axis Breakout Board】5 Axis breakout boad with cables,this breakout board needs to be connected to the parallel port and USB port of the....
♞【Power supply】400W,36V/9.7A switching power supply.

TB6612 motor driver with 1.2A per channel.
2 full H-bridges means you can drive 2-4 solenoids (only two can be active), two DC motors bi-directionally, or one stepper motor..
Runs at 2.7V-5V logic. The motor & logic voltage are separate..
Good for motor voltages from 4.5V up to 13.5V.

The DRV8825 stepper motor driver is a breakout board for TI’s DRV8825 microstepping bipolar stepper motor driver..
The module has a pinout and interface that are nearly identical to those of our A4988 stepper motor driver carriers, so it can be used as a....
The DRV8825 features adjustable current limiting, overcurrent and overtemperature protection, and six microstep resolutions (down to 1/32-step). It....

ATX power supply breakout board, with ADJ adjustable voltage knob, supports 3.3V, 5V, 12V and 1.8V-10.8V (ADJ) output voltage.
The voltage output terminals of the ATX power expansion board correspond to each screw terminal..
Compatible with 3.3V: STM32 MCU, network communication equipment, such as Wi-Fi Bluetooth and other devices, generally for microcontrollers, and some low-power modules, etc. 5V: Raspberry Pi, Banana Pi, Tinker Board, Nano Pi, USB interface, etc.
Compatible with 9V: Arduino, motor drive, display driver module, etc. 12V: motor drive, LED light, vehicle equipment with power requirements less than 24w, etc..

★L298N as main driver chip makes strong driving ability and strong anti-interference,dual-channel h-bridge driver working mode creates higher working efficiency,,drive stepper dc motors to work.to avoid damage the voltage stabilizing chip, please use an external 5v logic supply when using more than 12v.
★Dual-channel H-bridge driver working mode creates higher working efficiency..
★To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage..
★Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability..
★L298N as main chip. Can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors..

Motor drive module is ideal for use in battery-powered smart car, toy cars, robots..
Dual H-bridge motor driver, can drive two DC motors or a 4-wire two-phase stepper motor..
Supply voltage 2V -- 10V, can drive two DC motors or a 4-wire 2-phase stepper motors ,can achieve forward rotation or reverse rotation, it is possible to adjust the rotation speed..
Dual 1.5A * 2, the peak current to be 2.5A, built-in thermal protection circuit, do not be afraid motor stall burned, automatic recovery after the temperature dropped..
Use of imported original chip, built-in low on-resistance MOS switch, minimal heat, no heat sink, small size, low power consumption, is ideal for battery powered..

WIDELY OPERATING RANGE:Input:DC 10-60V,max drive current is 6A,Maximum wattage is 300W,PWM pulse width adjustable range: 10%-100%.
ADJUSTABLE KNOB:DC brush motor speed driver is designed with a voltage adjustment knob, very convenient for voltage control., DC output stepless adjustable..
WIRING TERMINALS DESIGN: The wiring terminals adopts fence type design and is with safety cover, and there is wiring marks on each terminal, please follow the marks when you are wiring..
SPECIFICATION:Small Size:0.4×3.9×2.4inch, DC motor speed controller has high precision, wide speed controlling range, low power consumption and long service life.
OCCASION:Pwm dc motor speed controller widely used for speed governing device drivers of packaging, printing, electronics, instrument meter, clothing machinery, medical machinery and other industries.

Aceirmc buck converter input voltage range is DC 6-40V, adjustable output voltage range is DC 1.2-36V, can be used to convert 24v to 12v 5v, adjustable output current range is 0-20A, max output power is 300W. The step down regulator can apply to constant output current..
With a wide input voltage range from 6V to 40V, the step-down converter can accurately adjust output voltage and current. The efficiency can be up to 95%,(measured at 20A, converting 24V to 12V)..
Short Circuit Protection: Self-recovery(cannot short circuit for long time). Plus, when input and output is common grounded, no-load CV output constant voltage,CC output constant current.
Adopting 75V / 80A large current dual MOS tube designed step-down board, Input and output use high frequency low resistance electrolytic capacitor, low ripple, and gives a stable output. Large current 30A connection screw terminals, more convenient to install.
Application: DIY stabilized voltage supply, LED car display, mobile power, industrial equipment appliances, LED driver, monitor, solar energy, fans, photovoltaic energy, motor, etc....