Best Led Pedestrian Signal Module

HiLetgo GY-NEO6MV2 NEO-6M GPS Flight Controller Module 3V-5V with Super Strong Ceramic Antenna for Arduino EEPROM APM 2.5

...tems such as electronic scales and sensor interfaces. Also features low noise, low input bias current, and low power consumption. The module has a fixed voltage output..
♥Basic Features: ✭Module Name AD620 Instrument Programmable Amplifier ✭Module size:50mm * 50mm ✭Module power supply: 5V-24V ✭Module input signal type: single-ended signal or differential signal ✭Module signal input and output range: the input signal range is within 100 microvolts of the power supply, and the output signal range is within the power supply ✭Module bandwidth: AD620: 120KHz (G=100), AD623: 800KHz (G=1), AD620/623 is lower than 50KHz at high gain, and higher than 1MHz at low gain.
♥ Other Features: ✭Module gain: When there is no solder slip, the AD620 will zoom by 10 times by default, and the AD623 will zoom by 20 times by default. During welding slip, AD620: G=1+50K/Rg, AD623: G=1+100K/Rg ✭Maximum magnification of the module: more than 2000 times (actual measurement), due to the large gain of the waveform frequency band, it is recommended to use multi-stage amplification with high gain ✭Fixed output voltage: 5V-10V (default delivery 5V).
♥ Other parameters: ✭Common mode rejection ratio: AD620: 100dB (minimum, G=10).

This is GY NEO 6MV2 GPS Module NEO-6M GY-NEO6MV2 Board with Antenna for Arduino New，The default baud rate: 9600..
Non-brand New Chip, but the use of the same effect.，Module with antenna, mini size with strong signal..
EPROM save the configuration parameter data when power down，With data backup，With LED signal lights，Compatible with various flight control....
Package Included:1Pcs GY NEO 6MV2 GPS Module NEO-6M GY-NEO6MV2 Board with Antenna for Arduino New(If the number of products received is incorrect,....
We highly appreciate all customers opinions to improve the selling, also if anything you unsatisfied, please contact us for probable best solution..

Fits: 2010-2013 Street Glides and Road Glides only.
Eliminates rapid flashing of turn signals.
Can be used with most custom turn signals (including halogen and LED signals).
Plug and play waterproof module works specifically with HD OEM alarm systems (TSSM) or HD turn signal module (TSM).
100 percent solid-state and produces virtually zero heat, unlike load resistors.

DEPENDABLE TO USE: The Mic sensor sound module is professional manufacturing, voice detection module has high performance, strong reliability, making sure safety use..
MAIN FUNCTION: This microphone sound detection module can detect sound strength of the environment, with high accuracy, great for professional usage..
ANALOG OUTPUT: The microphone sensor sound module supports analog voltage signal output, the signal amplitude is VCC/2, stable to use..
ADJUSATBLE GAIN: The mic sensor voice module has high sensitivity, built in amplifier circuit, and the gain can be adjusted as needed..
AD COVERSION: The microphone voice detection module can obtain the voltage signal of sound intensity through AD conversion..

Fixes Turn Signal ProblemLed flasher relay fixes for GM, GMC, Chevrolet problem with no turn signals or with 4 way flashers coming on when the directional is actuated..
FeatureIf you're going to do a LED light upgrade for your GM vehicle, this turn signal relay module is a must have item - solve the hyper flash problem with simple a plug and play..
FitmentsLed turn signal flasher compatible with 2003 2004 2005 2006 Silverado Tahoe, Sierra, Yukon, Avalanche, Suburban. Replace Part Numbers: LM487, 10383321, 15231201, 15764135..
NoteUse this gm led flasher relay for led turn signal, never cut your factory wires and install a load resister. (use the load resister basically shorting out the circuit).
Installation TipsTake out the dash cluster cover, remove two screws on the bottom of the steering wheel cover panel. Take the panel out. Use a clamp wrench to take out the original flasher, plug this flasher relay in, test the signals to see if hyper flashing goes away, then you are done..

Made with high quality 3-Emitter 5050 RGB SMD LED lights, 4 pieces LED Rings, in total 96 pieces 5050 SMD LED lights.
Comes with revolutionary new lens covers for a fluid, continuous output and comes with newly upgraded Radio Frequency remote control with 60 ft range.
7 Colors includes Red/Green/Blue/Amber/Magenta/Cyan/White, all necessary brackets and clips are included.
Tap the red/black wires from the module box to turn signal lamp stage-1 or red wire to ACC/Ignition, have the receiver of the module box placed behind....

This ir transmitter sensor module is directly launched by a single tube, it requires waveform modulation through the program..
It is suitable for infrared communication, infrared remote control, apply to a variety of platforms including for Arduino/51/AVR/ARM.
With signal indicating LED, easy to observe and debug..
Pin Definitions: (1) Output (2) Vcc (3) GND.
IR Infrared Transmitter Module Ir Digital 38khz Infrared Receiver Sensor Module For Arduino Electronic Building Block.

Receives standard DMX-512 digital control signal and transformrd it into PWM signal to adjust LED Lights.
Automatically adapt to DC5V-24V,Maximum power load: 300W (5V).
Aluminium housing,And High Power Output Max 60A For 5A Each Channel (5A*12 CH).
The DMX address can be set through dip switch,And You could connect with DMX digital console to achieve RGB dimming functions.
Easy Use for 4 Group RGB LED Strip,LED module And LED lights..