Honbay 50pcs Mixed Colour 5mm LEDs Pre Wired Light 12V 20cm Bulb
- High quality material, flexible cable, easy to use.
- For car, boat, industrial, camera, toys, DIY, etc..
Best Led Lamp 5mm 10mm
HH Fluorescent LH0450 125-7 Starter Base Lamp Holder With Two Hole Bra
- [Sturdy and Durable to Use]: The diode holder is made of quality plastic material, sturdy and durable to use, having long service lifespan.
- [Convenient to Use]: Plastic diode holders are for easily attaching LEDs to boards.
- [Application]: Suitable for Panel Mount LED indicator, Low Voltage Leddiode, Led Components, Panelmount Lighting, Lamp, DIY Project, Science Experiments, Hobby.
- [Diameter]: 3mm, 5mm, 8mm, total 3 different sizes of LED socket for your selection.
- [Package]: 50pcs LED plastic sockets, enough for your use.
- Easy to use and install, economical and practical.
Easycargo 100pcs Heatsink Assortment Kit Small Cooler Aluminum Heat Sink Set for Cooling Laptop CPU GPU VGA RAM VRAM VRM IC LED MOSFET Transistor SCR Voltage Regulator Without Thermal Tape
- 100pcs small to medium sizes of heat sink..
- Small anodized Aluminium: 20pcs 9x9x5mm, 8pcs 10x10x10mm, 8pcs 11x11x5mm (L*W*H).
- Medium anodized Aluminium: 8pcs 14x14x7mm, 8pcs 19x19x5mm, 8pcs 20x20x6mm, 2pcs 22x22x10mm (L*W*H).
- Silver Tone Aluminium: 20pcs 7x7x6mm, 10pcs 8.5x8.5x8mm, 8pcs 15x15x6.5mm (L*W*H).
- Can be used for cooling of variety of electronics components such as Development Boards VRAM VRM CPU GPU VGA RAM IC Chips LED Laptop MOSFET Transistor....
Partsam 10X 3.8 Amber 12V Front Side Marker 6 LED Trailer Truck Lorry Indicators Lights, Amber Rear Led Marker Trailer Parking Turn Signal Lights for Truck Bus Boat Rv Lorries SUV UTV
- ...ape bases are used to adhere to the back of the amber marker lights or to the surface to which the amber light is to be mounted, for waterproofing. Also you can use a little strong adhesive to be sure.
- These small thin clearance lights need to be hooked up to a 12v power source. Flux: 600Lumens (about 20 Lumens per lamp).
- Light Size: 75mm x 20mm x 5mm (2.95" x 0.8" x 0.2"), Light Size with Black Base: 96mm x 20mm x 10mm (3.8" x 0.8" x 0.4") and center to center distance: 3-5/16" approx..
- The wire length is about 6~7 inch, and you can put them in series with speaker wire to make them longer.
- Partsam Amber Led Lights function as marker lights, clearance lights, runnling lights, side marker lights, front parking lights, indicator lights, identification lights, boat interior lights, camper light, Decorate Light, under dash lights, walk way lights, Golf Cart Light, Interior Lights, trailer lights, truck lamps and so on.
- We also have customers asking whether they can be use as turn signal lights, they can, but they may be not that bright.
- The side marker indicator light is hardwired with 2 wires and can be used as constant on trailer lights: black is negative and the yellow wire is positive.
- These lights don't come with the on/o....
Que-T 10mm 2 LEDs Angel Eyes & Demon Eyes LED Headlight /Back Light for 1:10 RC Model Crawler Cars(Full White, 10mm)
- With switch, the middle lamp can be controllable, aperture was always Lights..
- Outer diameter:10mm /Middle Light Diameter: 5mm /Cord length: about 50cm..
- Bright LED light output,halo style bulb,bright colors,4.2v-6v input,2 lighting options,pre-wired..
- Universal model, easy to install,it works great with the RC Light Controller..
Partsam Thin Line 3.8" 6 LED Blue Side Led Trailer Marker Lights Sealed Clearance Light Indicators for Trucks Bus Trailer RV Camper Lorry Van UTV Marine Boat Stern Light Decoration Lights(10Pack)
- ... tape bases are used to adhere to the back of the blue marker lights or to the surface to which the blue light is to be mounted, for waterproofing. Also you can use a little strong adhesive to be sure.
- These small thin clearance lights need to be hooked up to a 12v power source. Flux: 600Lumens (about 20 Lumens per lamp).
- Light Size: 75mm x 20mm x 5mm (2.95" x 0.8" x 0.2"), Light Size with Black Base: 96mm x 20mm x 10mm (3.8" x 0.8" x 0.4") and center to center distance: 3-5/16" approx..
- The wire length is about 6~7 inch, and you can put them in series with speaker wire to make them longer.
- Partsam blue led lights function as marker lights, clearance lights, runnling lights, side marker lights, license plate lights, indicator lights, identification lights, boat interior lights, camper light, Decorate Light, under dash lights, walk way lights, Golf Cart Light,cockpit light, step lights, deck lights, trailer lights, led courtesy lights, stern light, stair lights, truck lamps and so on.
- Truly many customers use them as boat marine lights, very bright.
- The blue led strip light bar is hardwired with 2 wires and can be used as constant on trailer boat lights: black is negative and the red wire is positive.
Easycargo 100pcs Heatsink Assortment Kit Small Cooler Aluminum Heatsink Set for Cooling PC Laptop PS5 M.2 CPU GPU VGA RAM VRAM VRM IC LED MOSFET Transistor Voltage Regulator (Preapplied Thermal Tape)
- Update Version: 100pcs (18+82) small to medium sizes of heat sink. Pre-applied 3M 8810 thermal conductive adhesive tape..
- Small anodized Aluminium: 20pcs 9x9x5mm, 8pcs 10x10x10mm, 8pcs 11x11x5mm (L*W*H).
- Medium anodized Aluminium: 8pcs 14x14x7mm, 8pcs 19x19x5mm, 8pcs 20x20x6mm, 2pcs 22x22x10mm (L*W*H).
- Silver Tone Aluminium: 20pcs 7x7x6mm, 10pcs 8.5x8.5x8mm, 8pcs 15x15x6.5mm (L*W*H).
- Can be used for cooling of variety of electronics components such as Development Boards VRAM VRM CPU GPU VGA RAM IC Chips LED Laptop MOSFET Transistor SCR Southbridge Northbridge Voltage Regulators PS5 M.2 M2 SSD NVMe 2280 2242 22110 modules..
Bonlux 10W R7S LED Bulb 118mm, J Type 118mm LED Light Bulb T3 Double Ended R7S J118 LED Floodlight Replacement Bulb Daylight 6000K for Floor Lamp, Security Light (2-Pack)
- Technical Features -- 10W 118mm LED R7S Light Bulb - 12mm/0.47" Diameter, 118mm/4.65" Length - Voltage: AC 120V - Beam Angle: 360°, Non-Dimmable..
- Super Slim -- Standard R7S 118mm base, the diameter is only 12mm/0.47", Bonlux 10W 118mm R7S LED lamp can replace standard floodlight halogen double ended tubes pefectly..
- Excellent Heat Dissipation -- R7S LED J118 flood light has high quality ceramic body and PC cover, excellent thermal conductivity, good heat dissipation, low power consumption, superior energy efficiency, reduce expense at electricity bill and frequent bulb changes..
- Widely Applications -- 118mm R7S LED light for use in Floodlight Replacement Bulb, Work and Security Lights, Workshop Lighting, Stage and Studio Lamp, LED Ceramic Metal Halide Lamp, Floor Lamps, Speciality Lights, General Lighting..
- Energy Saving -- 10W Double-ended J118 R7S LED Light repalcement for 75W halogen bulbs, save about 90% on your electricity bill..
Partsam 20Pcs 3.8" 6 LED Clearance Truck Trailer RV Side Marker Indicators Purple 12V, Purple Trailer Marker Lights, Rear Side Marker Lamp, Led Marker Lights for Trucks, Cab Marker, RV Marker light
- ...uded. The foam tape bases are used to adhere to the back of the marker lights or to the surface to which the light is to be mounted, for waterproofing. Also you can use a little strong adhesive to be sure.
- These small clearance lights needs to be hooked up to a 12v power source. Flux: 600Lumens (about 20 Lumens per lamp).
- Light Size: 75mm x 20mm x 5mm (2.95" x 0.8" x 0.2"), Light Size with Black Base: 96mm x 20mm x 10mm (3.8" x 0.8" x 0.4") and center to center distance: 3-5/16" approx..
- The wire length is about 6~7 inch, and you can put them in series with speaker wire to make them longer.
- Partsam Led Lights function as marker lights, camper light, Decorate Light, under dash lights, walk way lights, Golf Cart Light, Interior Lights, trailer lights, truck lamps, clearance lights, runnling lights, side marker lights, front parking lights,safety light,warning light,underglow light,indicator light and so on.
- The indicator light is hardwired with 2 wires and can be used as constant on trailer lights: black is negative and the other is positive.
- These lights don't come with the on/off switch and Wire leads come out the back in the center so you must drill a hole in the mounting surface for them.