Best Large Tap Sizes

Happybuy 110Pcs Tap & Die Set Tungsten Steel Titanium Tap & Die Metric Tool Tap & Die Combination Set For Cutting External & Internal Threads

Premium Quality: High-duty heat-treated Tungsten steel construction, high-hardness, wear-resistant, and its service life is 5-10 times longer than that of non-tungsten taps, durable and reliable for your long-lasting use..
Excellent Performance: Fully ground & high-precision tap is super-sharp for your tapping and chip removing operation, running smooth and efficient, offering you excellent performance..
Reinforced Stability: Each dies is designed with a lock hole, it can be locked tightly after the screw is aligned and locked, ensures double stability during your operation..
Adjustable Tap Wrench: Tap wrench is adjustable: you can set the adjustable basin wrench to either its position for turning clockwise (tightening) or turning anti-clockwise (loosening). You can do this by flipping the jaws 180 degrees over its pivot..
Most Popular Sizes Included: This tap and die set comes with 110 pieces in total: 35 pcs plug taps, 35 pieces taper taps, 35 pcs dies, 2 tap holders(M2 - M12 (1/16" - 1/2"& M6 - M20 (1/4" - 3/4")), 2 die holders (200mm (1" diameter bore)& 270 mm (1 1/2" diameter bore) and 1 T-bar tap wrench, most popular sizes included.

Tap Sizes: M2.5 x 0.45, M3.0 x 0.50, M3.5 x 0.06, M4.0 x 0.70, M5.0 x 0.80, M6.0 x 1.0,M8.0 x 1.25,M10.0 x 1.50,M12 x 1.75.
Drill Metric Sizes: 2.05,2.50,2.90,3.30,4.20,5.00,6.70,8.50,10.2mm.
Case Overall Dimension: 8''L x 4-3/8''W x 1-1/4''H *Estimate Only*.

CLEAN CUT RESULTS: Start DIY garage and workshop tapping and threading with the Hi-Spec 39 Piece Metric Tap and Die Tool Set. Whether its internal or external rethreading, cut new material, chase damaged or old screws, repair rusty nuts, bolts and spark plugs.
34 PIECE METRIC SIZES: Most popularly used coarse and fine thread sizes and pitches of three and four flute tapered and plugged taps and dies. Metric Tap and Dies: 8 thread sizes from M3 to M12 with 16 pitch sizes plus NPT (1/8-27).
GOES THROUGH METALS: For materials such as carbon alloy steels, cast iron, aluminium, brass and bronze. Using premium GCr15 Alloy steel, a high carbon chromium bearing steel with high Rockwell hardness, contact fatigue performance, and corrosion resistance.
3 TAP & DIE WRENCH HANDLES: Just fix the tap or dies tools into the steel alloy wrench handles with adjustable fittings and get turning. Includes a handy mini-screwdriver to assemble and fix the dies.
SCREW PITCH GAUGE: Easily and accurately measure the pitch or lead of a screw thread with the 16-Blade Screw Pitch Gauge. All tools and accessories are kept tidy and organised in a slimline case for simple storage and carry.

Tap and Die Bit Diversity – These tools are sold as a set for good reason. You really should look to get as much diversity in the sizes of the taps and dies as you can. That way you will be able to pull the right size out of the box when you need it..
Wrenches – All tap and die bits need to be mounted in a wrench. Broadly speaking, they are all roughly the same, with a few notable exceptions. The tap wrench from Muzerdo, is the best on the market..
Construction Material – Steel is the base metal used in the construction of these sets – but not all steel is created equally! Look for steel alloy or, even better, Titanium tipped cutting surfaces. The better the metal the tougher the tap and die so they so they can cut into more.
Metric/SAE – The size of the tap and die is also important. Metric is of course the European measurement system, SAE are based on US sizes (so use inches instead of millimeters). This is important as you may struggle to use a SAE tap and die set on a vehicle with metric measurements. If the car is made in the US, it probably uses SAE measurements. If it is a European carmaker, it’s probably the opposite. If can look for a set with dual Metric and SAE compatibility of course then you don’t have t.

Tap and Die Bit Diversity – These tools are sold as a set for good reason. You really should look to get as much diversity in the sizes of the taps and dies as you can. That way you will be able to pull the right size out of the box when you need it..
Wrenches – All tap and die bits need to be mounted in a wrench. Broadly speaking, they are all roughly the same, with a few notable exceptions. The tap wrench from Muzerdo, is the best on the market..
Construction Material – Steel is the base metal used in the construction of these sets – but not all steel is created equally! Look for steel alloy or, even better, Titanium tipped cutting surfaces. The better the metal the tougher the tap and die so they so they can cut into more materials and they will stay sharper for longer..
Metric/SAE – The size of the tap and die is also important. Metric is of course the European measurement system, SAE are based on US sizes (so use inches instead of millimeters). This is important as you may struggle to use a SAE tap and die set on a vehicle with metric measurements. If the car is made in the US, it probably uses SAE measurements. If it is a European carmaker, it’s probably the opposite. If can look for a set with dual Metric and SAE compatibility of cour....

...t, tap and die set SAE and standard craftsman.
➤[Package include]: 17xTaps for Internal Threads.
➤[Tap and Die Sizes]: Coarse Thread (NC): 4-40 NC, 6-32 NC, 8-32 NC, 10-24 NC, 12-24 NC, 1/4-20 NC, 5/16-18 NC, 3/8-16 NC, 7/16-14 NC, 1/2-13 NC.
Fine Thread (NF): 10-32 NF, 1/4-28 NF, 5/16-24 NF, 3/8-24 NF, 7/16-20 NF, 1/2-20 NF.