Best Isolation Switch

5v Relay Board Relay Module 1 Channel Opto-Isolated High or Low Level Trigger

【1 Channel Relay Module】- This Relay Board provides a single relay that can be controlled by any 5V digital output from your microcontroller..
【Main Specification】- Peak Load of NO Connector: AC125~250V/10A, DC28~30V/10A.
【Adopted SMD Optocoupler Isolation】- The isolation circuit prevent damages to I / O port by relay switch current..
【Wide Application】- These 5v relay board works well with ARM /PIC /AVR /MCU/Raspberry/CNC machine/ PS4 etc..
【Humanization Design On Interfaces】- All interfaces can be directly wired out through the terminals..

The contact design before the break point can switch between battery packs without interrupting the power supply..
Battery switch m series ON/OFF with knob, part number 6006, is a single loop ON-OFF switch. Switch a single battery to a single load group, suitable for low amperage battery switch hole style..
Anti-ignition, can be safely installed on gasoline-powered boats, the chassis design allows surface, front panel or rear panel installation..
300A continuous rating-45% higher than standard switch, continuous rating: 300A, maximum voltage: 48V DC, with luminous label..
Isolation cover with buckle part can protect the rear contact..

ISOLATE AND SECURE - Battery isolation switch helps you isolate and secure the electrical system, eliminate any power draw from the battery when vehicle or boat is not in use, disconnects the battery safely..
WITH 2 KEYS - Equipped with 2 keys. Easy to install & simple to use..
WATERPROOF COVER - We provide you with a waterproof cover to protect the keyhole against the dust and water..
HIGH QUALITY - Copper terminals with galvanized steel hex nuts and washers, rust and corrosion resistant..
WIDE APPLICATION - The battery switch is widely used for car, marine, boat, RV, camper, travel trailer, truck, ATV, UTV, battery banks, and other 12V/48V devices..

The Diamond CX-310A is a low loss, three position coaxial switch providing very low loss and high isolation..
It is rated DC to 800 MHz and can handle up to 1500 watts at HF frequencies..
This switch utilizes SO-239 jacks for input and output..

Output signal DC: 0-5V / 0-10V /4-20mA three forms are available. The outer casing is made of self-extinguishing material, safe and durable..
The measured current AC: 0-10A / 20A / 50A can be selected. Magnetic hysteresis less than 1%, can be used in strong magnetic field conditions..
Mutual inductance current monitoring, high current detection accuracy, stable performance, safe isolation of input and output. It is used for AC current monitoring, detection, current overload protection, and is also used as an electronic switch for automatic control systems..
Through-heart structure design, isolation withstand voltage up to 2000V AC. It is suitable for various applications requiring current and voltage conversion..
Installation and using are easy and convenient, there is no need to connect the dc series into the circuit during measurement. It has the characteristics of strong overload ability, high precision, high isolation, high security, low power consumption and strong anti-interference ability..

This Relay Board Maximum load: AC 250V/10A, DC 30V/10A With power and relay action indicator.each relay has normally open and normally closed contact. Can be selected by jumper relay and TTL or ground..
Main Specification Peak Load of NO Connector: AC 250V/10A, DC 30V/10A.
These Relay Board use photocoupler isolation that has strong driving ability and stable performance.The isolation circuit prevent damages to I / O port by relay switch current.The module has a jumper so you can set rather the unit state changes with high or low signal. Has screw terminals for relay (NC,C,NO) and for input.
Using SMD optocoupler isolation, strong driving capability, stable performance.Fault tolerant design, even if the control line is broken, the relay will not operate.
And interface design humanized, all the interface can be directly connected through the terminal lead, so convenient..
Wide Application These 5V relay board works well with for ARM /PIC /AVR /MCU/Raspberry/CNC machine /etc..

【1 Channel Relay Module】- This Relay Board provides a single relay that can be controlled by any 5V digital output from your microcontroller..
【Main Specification】- Peak Load of NO Connector: AC125~250V/10A, DC28~30V/10A.
【Adopted SMD Optocoupler Isolation】- The isolation circuit prevent damages to I / O port by relay switch current..
【Wide Application】- These 5v relay board works well with Arduino/ ARM /PIC /AVR /MCU/Raspberry/CNC machine/ PS4 etc..
【Humanization Design On Interfaces】- All interfaces can be directly wired out through the terminals..

This Relay Board Maximum load: AC 250V/10A, DC 30V/10A With power and relay action indicator.each relay has normally open and normally closed contact. Can be selected by jumper relay and TTL or ground..
Main Specification Peak Load of NO Connector: AC 250V/10A, DC 30V/10A.
These Relay Board use photocoupler isolation that has strong driving ability and stable performance.The isolation circuit prevent damages to I / O port by relay switch current.The module has a jumper so you can set rather the unit state changes with high or low signal. Has screw terminals for relay (NC,C,NO) and for input.
Using SMD optocoupler isolation, strong driving capability, stable performance.Fault tolerant design, even if the control line is broken, the relay will not operate.
And interface design humanized, all the interface can be directly connected through the terminal lead, so convenient..
Wide Application These 12V relay board works well with for ARM /PIC /AVR /MCU/Raspberry/CNC machine etc..

Standard serial port level, RS232 model or RS485 model can switch by software.
Conversion direction can be set to: CAN?? Serial, CAN?Serial, CAN?Serial.
Serial Bus baud rate range from 600bps to 115200bps.
CAN-Bus supports CAN2.0A and CAN2.0B frame format, conform to ISO/DIS 11898 standards.
CAN-Bus baud rates range from 5Kbps to 1Mbps.
CAN-Bus interface with electrical isolation.
CAN-Bus isolation converter insulation voltage: DC 1500V.
Working temperature range from -40 to 85 °C.