Best Isolated Current Transducer

MASTECH AC Current 0.1A-400A Clamp Meter Transducer True RMS MS3302

⚡【AC/DC amp clamp meter】 Hantek AC/DC Current amp Clamp probe with bnc for oscilloscope, 400Hz Bandwidth, 1mV/10mA, 650A..
⚡【Multifunction】It is a transducer which allows your multimeter to measure current data and enable your oscilloscope to measure the current waveforms..
⚡【BNC Probe】if connect to an oscilloscope by BNC type connector, you're able to observe the current waveforms..
⚡【Application】1.Power circuit measurement and malfunction analysis.
2.Motor drive of frequency converter (or other electronics) measurement.
3.Power electronics equipments measurement..
⚡【What you will get】1*AC/DC Current clamp CC-650,1*English Manual..

【Mini Split Base Current Transformer】It's the smallest one compared to the similar products (output 100MA).Current Transformer, 100A 100mA AC Current Sensor, Split Core Amp Transformer Sensing Relay, Mini Clip-on Easy to Install CT Without Power Off. current sensor structure sensor.
【Professional Use】Current transducer used for energy meter in special.
AC 220v, 380v power supply can both be applied.plit Core Current Transformer,AC Current Sensor,Output Class Analog Sensor,Working Principle Magnetic Sensor, Useful for Measuring Whole Building Electricity Consumption.current sensing relay isolation.
【Good Mechanical Properties】Fully enclosed, good mechanical properties and environmental resistance, strong voltage isolation capability, safety and reliability..
【Snap Joint Structure】The diameter of inner hole is 16mm, the accuracy is 0.5 grade, Using snap joint structure, it can be fixed to the cable directly through nylon ties..
【Easy to use】When you fix the energy meter, you don't need to cut off the power if you use this product. Split Core Current Transformer Coil Sensor for 100A Amp Energy Meter.ac transformer amp meter amp tester.

It is 4 Channel Isolated 5V 10A Relay Module, each relay can individually switch on/off by an opto-isolated digital input, Standard interface can be directly connected with microcontrollers and be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, DSP, etc., very convenient..
Equipped with high-current relay, maximum load: AC250V 10A, 15A 125VAC, DC30V 10A.
RELIABLE: Fault-tolerant design, even if the control line breaks, the relay will not move.
With optical coupling isolation, triggering more reliable, more stable..
EASY to INSTALL: Equipped with screwed terminal plate and fixed bolt holes(diameter: 3.1 mm) on both sides for easy installation..
High/Low level trigger can be selected by jumper. Very versatile, you can reverse the input logic with the jumper..

⚡【AC/DC amp clamp meter】 Hantek AC/DC Current amp Clamp probe with bnc for oscilloscope, 20kHz Bandwidth, 1mV/10mA, 65A.
⚡【Multifunction】It is a transducer which allows your multimeter to measure current data and enable your oscilloscope to measure the current waveforms..
⚡【BNC Probe】if connect to an oscilloscope by BNC type connector, you're able to observe the current waveforms.
⚡【Application】1.Power circuit measurement and malfunction analysis.
2.Motor drive of frequency converter (or other electronics) measurement.
3.Power electronics equipments measurement..
⚡【What you will get】1*AC/DC Current clamp CC-65,1*English Manual..

10 ISOLATED OUTPUTS:Donner DP-1 9V Guitar Pedal Power Supply has 10 outputs ,which includes 7 ways 9V 100mA, 1 way 9V 500mA, 1 way 12V 100mA, 1 way 18V 100mA..
NOISE REDUCTION CIRCUIT DESIGN：Donner Guitar Pedal Power Supply Quality is made of aluminum alloy material, which makes it light, and portable. It has a noise reduction function, low noise gives you a better experience, and direct current increases the stability of the power supply during use..
【Super Power Adapter】Donner DP-Z 9V Guitar Pedal Power Supply equips with superpower adapter: DC 18v 2000mA ，this powerful input ensures that every output is in the best possible state..
【10 Isolated Outputs + 1 USB charge port 】 Donner DP-Z 9V Guitar Pedal Power Supply has 10 outputs ,which includes 4 x 9V 100mA, 3 x 9V 300mA, 1 x 9V 500mA, 1 x 9V/12V 500mA, 1 x 18V 300mA with 1 x DC 18V input, 1 x USB charge port. 10 Isolated Output ,5v 1000 mA USB charge port Meet the power demand of Mobile devices ..
【Noise Reduction Circuit Design】Donner Guitar Pedal Power Supply Quality is made of aluminum alloy material, which makes it light, and portable. It has a noise reduction function, low noise gives you a better experience, and direct current increases the stability of the power supply during u....

Electrically isolated from high voltage power source which eliminates risk to delicate monitoring equipment and also minimizes safety concerns.
Diameter of the hole through sensor is 3/4 inch(19 mm).
Loop through sensor multiple times to strengthen signal. For example, if your current signal is only 0.2 Amps, you could loop the wire through the....

Electrically isolated from high voltage power source which eliminates risk to delicate monitoring equipment and also minimizes safety concerns.
Diameter of the hole through sensor is 3/4 inch(19 mm).
Loop through sensor multiple times to strengthen signal. For example, if your current signal is only 0.2 Amps, you could loop the wire through the....