Best Ic Voltage Regulators

Bridgold 10pcs TIP102 102 Bipolar BJT Single NPN Darlington Transistor 100 V/8 A,3-Pin TO-220

High DC Current Gain − hFE = 2500 (Typ) @ IC = 4.0 Adc.
Collector−Emitter Sustaining Voltage − @ 30 mAdc VCEO(sus) = 100 Vdc (Min) − TIP102, TIP107.
Monolithic Construction with Built−in Base−Emitter Shunt Resistors.
Low Collector−Emitter Saturation Voltage − VCE(sat) = 2.0 Vdc (Max) @ IC = 3.0 Adc = 2.5 Vdc (Max) @ IC = 8.0 Adc.
We have undergone rigorous testing and stable performance.

2V to 39V .0.5 Watt Zener Diodes Assortment Set (Pack of 30 Values, Each 10 Pieces, Total 300 Pieces).
The assortments contain the following voltage: 2V 2.2V 2.4V 2.7V 3V 3.3V 3.6V 3.9V 4.3V 4.7V 5.1V 5.6V 6.2V 6.8V 7.5V 8.2V 9.1V 10V 11V 12V 13V 15V 16V 18V 20V 22V 24V 27V 30V 39V.
These diodes are widely used as voltage references and as shunt regulators to regulate the voltage across small circuits..

【Specifications】Voltage Supply: 9-12V DC Input.
Input Distortion: less than 1% (at 1KHz).
【welding steps】The welding installation considerations, follow these steps: First,the components are welding the front board, from low to high principles, namely the first low welding components, such as, capacitor, resistor, diode, etc.Then welding IC socket, terminal blocks, finally power socket, adjustable potentiometer..
【Debugging steps】After completion of welding on IC, XR2206, you need to pay attention to the direction of IC, or insert the might damage the chip! Check IC for errors, if any, please correct in time..
【Power】 Insert the power supply, power supply for 5.5 x 2.1 port, inside and outside is negative polarity.
Fitting for 9-12 v power supply voltage, and the waveform may not be stable for more than 12V..
【Please note】these are DIY kits, you need to follow the welding steps in our description and complete the final installation..

COMPATIBLE MODELS: Voltage Regulator Rectifier Fit for 2006 2007 2008 Glide 2006 2007 2008 Road Glide 2006 2007 2008 Road King 2006 2007 2008 Street Glide.
OEM NUMBER: Replaces HARLEY-DAVIDSION voltage regulator part numbers:H 74505-06 74505-06A 498269 49-8269 498276 49-8276. Please check OEM number before buying..
HIGHT QUALITY: Voltage regulator rectifier ueses original stabilivolt and advanced heat conduction system to control the output. Voltage stabilize at 12V to Protech Battery System, Lights,Reduce Load, and Extending Mortorcycle Service Life.ALL Regulators have been Tested Strictly to make sure every regulator have original HARLEY regulator Performance..
GOOD MATERIAL:Voltage rectifier regulator use high quality aluminum Shell , highest grade and thick aluminum substrate , high-performance electronic components..
SATISFAY AFTERSELL SERVICE:All Voltage Regulator Rectifier will Test Before Shipping. If you have Any Dissatisfaction with Our Product, Please let us Know and we will.

...758-LCB current sensor. The ACS758 consists of a precision, low-offset linear Hall sensor circuit with a copper current path close to the wafer. The current applied through the copper current path is capable of generating a magnetic field that can be induced by the integrated Hall IC and converted to a proportional voltage.003cbr003e.
Device accuracy is optimized by placing the magnetic signal close to the Hall sensor. The accurate, proportional output voltage is provided by a stable chopper-type, low-bias BiCMOS Hall IC that is factory-precisely programmed.003cbr003e.
The internal resistance of this conduction path is typically 100 μΩ with low power loss. The thickness of the copper wire allows the device to operate under high overcurrent conditions. The terminals of the conduction path are electrically isolated from the sensor pins (pins 1 to 3). In this way, the ACS758 sensor IC family can be used in applications that require electrical insulation without the use of opto-insulators or other expensive insulation techniques.003cbr003e.
Perform RC filtering on the output and use the op amp to build a voltage follower circuit to make the output more stable and better match the impedance of the A/D channel of the microcontroller. At the same time, two o....

SET OF 2 REGULATORS - OXYGEN 249-499B and PROPANE 249-500B.
A Set of Pre-Set Regulators, one for the Oxygen Tank and the other for Fuel made by Smith Equipment, Regulators are designed to use with disposable tanks. Ideal for the Smith Little Torch, when using them in Hobby and Craft also for Jewelry Repair and soldering work..