Best Hydraulic Flow Meter

Tolsous 1 Spool Directional Control Valves 11 GPM 3600 PSI MAX High Pressure Integral Valve Double Acting for Small Tractors Tractors Loaders Log Splitters

  • SPECIFICATIONS: Our 3 spool directional control valve for double-acting hydraulic rams has 21 GPM, 4-way 3 pos spring center, SAE 10 inlet and work ports and SAE 12 outlet ports. This hydraulic flow control valve has 4-way valving, adjustable 1500 with 3625 PSI..
  • VERSATILE: This G series P80 DCV has a 3 position, 4-way valving that allows an actuator to open and close. This 3 spool control valve can be used in any hydraulic circuit..
  • PRECISE FLOW: Simple and compact, the hydraulic joystick valve has one spool with a 21 GPM flow rate that precisely controls the direction of the flow of hydraulic fluids. This plow valve has a wide range of applications, including in log splitters..
  • MANUAL CONTROL: This high-pressure control valve comes with a joystick lever actuator for controlling the spool. You can control the log splitter valve manually, without an external, additional control system..
  • TANDEM CENTER: This adjustable relief valve is equipped with a spring tandem center. Since the fluid directly flows back to the hydraulic tank the hydraulic orbit motor prevents overheating and reduces noise during operation..
Check Stock

Horiba 9096001700 Plastic Body PH Electrode

  • Modular design makes it suitable for use with output modules, sensors and remote transmitters.Compact structure, easy to install.Intuitive clear reading, high reliability, measuring accuracy is ±1%.High-definition displays show both instantaneous and cumulative flow.Can be widely used to measure diesel, kerosene, gasoline, etc..
  • This digital turbine flow meter has modular design, high accuracy, compact size and stable performance. Easy to replace and maintain internal components. Suitable for use with output modules, sensors and remote transmitters..
  • Malfunction and solution:The flow meter is not accurate. 1. The method of field calibration is not correct. Calibrate again. 2. The flow rate on the meter is below the lowest. Increase the flow rate. 3. The flow meter is blocked by the dry liquid. Take out the impeller and clean it carefully and make sure the impeller turns freely..
  • 4. The impeller is wrapped by the sealing material. Remove the meter and make sure the impeller turns freely. 5. Too close to the impeller. Install properly 6. Too close to the motor or electronic noise environment.
  • The meter can not calibrate. 1. Circuit board is break down. Replace the circuit board. 2. Button is fail to press. Replace the circuit board..
Check Stock

1/2\ Skid Steer Bobcat Flat Face Hydraulic Quick Connect Couplers w Dust Caps,1/2\ NPT Thread+ 1/2 Body Hydraulic Couplers for Skid Steer Bobcat Case/Kubota/New Holland

  • The flat face hydraulic couplers with 1/2" NPT thread+ 1/2 body. The hydraulic quick connect coupler is an ISO 16028 flat face style, fits all standard flow skid steers attachments. Impoved design high flow performance and maximum service life..
  • The universal hydraulic quick disconnect coupler & plug interchange with most models of skid steers loaders including Bobcat Case / New Holland, Kubota couplings which made to ISO 16028 standard.
  • Applications:This flat face couplers connect used in the agriculture, construction, logging industries etc,skid loader attachment,hydraulic tools,Agricultural implements,equipment attachments, drain lines,construction，industrial hydraulic lines..
  • The flat face hydraulic quick connect couplers is valve design and structure for minimize pressure adrops and fluid losses. Sleeve locking mechanism prevents accidental disconnection..
  • Our bobcat skid steer hydraulic couplers are made by heavy duty harden steel construction with zinc nickel plating for superior corrosion resistance. 5076 PSI Rating , 12-23 GPM Flow Rate. Warm Tips: Make sure relieve all pressure on the skid steer from the lines before connect/disconnect them.Just line up the flat faced hyd fittings and push couplers to gather,male to female, female to ma....
Check Stock

CGOLDENWALL Turbine Flow Meter Fuel Meter Digital Flowmeter with FNPT Thread, Flow Meter for Water Diesel Kerosene Gasoline, Flow Rate Range 2.5-26GPM (1 inch Flow Meter)

  • FLOW METER: Before use, please calibrate the flow meter with the liquid to be tested. And the flow rate of the liquid should exceed 2.5 gallons per minute, if the flow rate is too slow, the flow meter cannot measure normally. There is no battery included..
  • MULTI-FUNCTION DISPLAY: High-definition LCD display, can read single cumulative flow, instantaneous flow and total cumulative flow. The clear function can clear the value of cumulative flow, to make sure it is always within the measuring range. If your flow meter cannot work, please contact us in time..
  • HIGH-QUALITY MATERIALS: The aluminum alloy housing is sturdy, durable and corrosion-resistant, which have a long service time. The PCB circuit board make the battery have a long service life, and safe in use. Please NOTE: the LCD display is not water proof.
  • INSTALLATION: The flowmeter can be installed in horizontal and vertical directions, but the flow direction of the liquid needs to be consistent with the direction of the arrow on the flowmeter. There is no direction requirements for the installation of the display screen..
  • MEASURABLE LIQUIDS: The turbine flow meter can used for measuring the water, gasoline, diesel, kerosene, methanol and other low-corrosive, non-viscosity liquids..
Check Stock

CGOLDENWALL Turbine Flow Meter Digital Fuel Flowmeter with FNPT Inlet/Outlet, 1inch Flow Meter for Water Diesel Kerosene Gasoline, 2.5-26GPM /9-100LPM (1 inch)

  • FLOW METER: the 1 inch flow meter can read instantaneous flow rate, single cumulative flow and total cumulative flows. But it has minimum flow rate requirment, if the flow rate of the tested liquid is lower than 2.5 gal/min, the readings will be inaccurate..
  • TECHNICAL PARAMETERS：① diameter of water inlet: 32mm.
  • ③ the flow speed requirenment for tested liquid: 2.5~26 gal/min.
  • ⑥ max temp of tested liquid: 158°F/70°C.
  • MULTIPLE UNITS: the flow meter provide 4 meauring units for option, which are liter, gallon, pint and quart. The unit defaults to gallons, if the unit is not gallons, please refer to the user manual to change the unit to the needed one..
  • NOT WATER PROOF: the flow meter is not water proof, please keep the display from water during use, to avoid chip damage. We upgraded The flowmeter has been upgraded from never-sleep model to auto-sleep model, which automatically dims the screen when no liquid is flowing through it..
  • WIDE APPLICATION: The turbine flow meter can used for measuring the water, gasoline, diesel, kerosene, methanol and other low-corrosive, non-viscosity liquids. If there is any problem, please contact us in time..
Check Stock

Chief Directional Control Valves 1 Spool 4 Way 4 Position - Hydraulic Directional Control Valve with Spring Center - 25 GPM, 1/2\ NPT Work Port, 3/4\ NPT Outlet Port, 3000 PSI, 16 lb, 220572

  • SPECIFICATIONS: The Chief P40 manual Directional Control Valve for hydraulic systems has a 4 way, 3 pos tandem center with 10 GPM, maximum working pressure of 3625 PSI, temperature of 176°F, standard SAE 8/10 inlet/outlet ports. It weighs 9.4 lb..
  • FAST ACTING: Our 4 way hydraulic control valve has 4 ports that facilitate super fast extension and retraction of double-acting hydraulic cylinders, producing sufficient pressure required in a wide range of applications..
  • PRECISE: This directional control valve hydraulic has a two spool construction equipped with lands and undercuts. The precision machined construction allows the spools to open and close fluid flow paths effortlessly with high accuracy every time..
  • EFFICIENT: Our 3 pos, hydraulic directional control valve allows the hydraulic fluid back into the tank without forcing it over the relief valve, reducing heat generation and a buildup of backup pressure..
  • MULTIPURPOSE: The P40 hydraulic valves are extremely versatile and can perform several functions in their central position - they can easily unload hydraulic pumps, stop, allow, or change the direction of fluid flow in hydraulic circuits. Power beyond and closed center plugs may be added and are sold separately..
Check Stock

Chief G Series P80 Hydraulic Directional Control Valves - Hydraulic Speed Control Valve - 3 Spool, 21 GPM, 4 Way 3 Pos Spring Center, SAE 10 Inlet and Work Ports, SAE 12 Outlet Ports, 3625 PSI

  • Durable - The hydraulic directional control valve is a cast-iron structure, which can be used for a long time.
  • 5 Spool Hydraulic Valve - The hydraulic valve can manage and guide the flow of hydraulic oil between hydraulic pumps and hydraulic cylinders, motors, tanks, and more.
  • Double Acting - This control valve comes with 5 spools and SAE O-ring in/out ports. All spools are standard double-acting spools, which are very suitable for double-acting cylinders.
  • High Efficiency - The relief valve range is up to 3600 PSI and the maximum flow is up to 13 GPM.
  • Widely Used - The hydraulic directional control valve is very suitable for small tractors, tractor loaders, fellers, forklift environmental vehicles, light loaders, log splitters, and more.
Check Stock

OTC Tools 4278 100 GPM Hydraulic Flow Meter

  • Tests hydraulic oil circuits on your machinery with high accuracy and measures flow from 2.5 to 100 gpm.
  • Flow Accuracy to +/- 1 percent of indicated value and Pressure accuracy of +/- 1.6 percent of full scale.
  • Pressure range up to 6,000 psi and Temperatures up to 250 deg F.
  • Standard burst disc protection system prevents spillage of hydraulic fluid in the event of an overpressure condition.
  • Accommodates bi-directional flow, reads flow in both directions, pressure on the high side of valve and Port is 1-5/16" -12UN #16 SAE ORB.
Check Stock

Hydraulic Valve 2 Spool, Hydraulic Directional Control Valve, 11GPM Hydraulic Joystick Control Valve for Tractors Loaders, Double Acting Cylinder Spool

  • Hydraulic directional control valve comes with 2 spool and #8 BSPP in/out ports, and the 2 spool hydraulic joystick fits for small tractors, tractors loaders, log splitters, and so on..
  • Hydraulic control valve 2 spool for operating double acting cylinders. Durable cast iron construction provides long-term usage..
  • The hydraulic valve 2 spool, hydraulic control valve for tractor loader, all spools standard come with spring return, which can return to the neutral position..
  • The hydraulic spool control valve's relief valve range is up to 3600 PSI and the maximum flow is up to 11 GPM. The hydraulic valve 2 spool replacement for hydraulic control valve 2 spool, hydraulic directional control valve, hydraulic spool control valve, joystick hydraulic valve, 2 spool hydraulic joystick, hydraulic control valve for tractor loader, hydraulic joystick control, hydraulic loader valve joystick, hydraulic loader control valve joystick..
  • You will get 1pcs 2 spool hydraulic control valve. We provide the best after-sales service, if you have any questions, please feel free to contact us, we are happy to serve you..
Check Stock