Best Esr Analyzer

Signstek MESR-100 V2 Auto Ranging in Circuit ESR LCR Meter Capacitor / Low Ohm Meter Up to 0.01 to 100R, Support in Circuit Testing

Using true 100 KHz sine wave to measure the ESR value, which is equal to the testing method of capacitor manufacturer..
Dual terminal, for fast and easy inspect general capacitor or resistor, a printed ESR table for fast check..
Measuring range from 0.001 to 100.0R, support IN CIRCUIT Testing..
Auto-ranging capacitor ESR and Low Ohm Meter..

This MESR-100 V2 auto-ranging capacitor ESR and low Ohm meter measuring range is 0.001-100.0R, support in circuit testing..
It is the series resistance inside the capacitor, and 100kHz is used to remove the impedance 1/(2*pi*F*C). When the impedance becomes smaller, the real series resistance value can be measured to determine whether the capacitor is bad/damaged or in good condition..
Our ESR meter only applies less than 15mV DC or peak to peak on a good capacitor, as a result we can use it as in circuit test..
During repairing TV, LCD, Audio board, etc. we can in circuit testing the capacitor is good or not.【Note:The Capacitance Meter is used for testing the internal resistance of the capacitor, not for testing capacitance value.】.
Dual terminal, for fast and easy inspect general capacitor or resistor, a printed ESR table for fast check.Equipped with a SMD alligator clip for more accurately testing..

This MESR-100 auto-ranging capacitor ESR and low Ohm meter measuring range from 0.001 to 100.0R, support in circuit testing..
Capacitance meter is a series resistor inside capacitor, using 100kHz to remove the impedance 1/(2*pi*F*C).The impedance become small, and we can then measure the true series resistor value..
Our ESR meter only applies less than 15mV DC or peak to peak on a good capacitor, as a r-esult we can use it as in circuit test..
Dual terminal, for fast and easy inspect internal resistance of the capacitor, a printed ESR table for fast check..
Note:The Capacitance Meter is used for testing the internal resistance of the capacitor, not for testing capacitance value.[Note: without SMD test clips].

✔️ Ships almost completely assembled. Minimal assembly effort required and 5/64” Steel Tubing for ROCK SOLID stability. Compatible and drilled....
✔️ Folds up for easy storage and the rugged powder coat finish with Anti-Slip rubber feet to prevent slipping on carpet & hardwood surfaces. (ESR....
✔️ Full length Pedal Deck w/ full range mounting capabilities including angle adjustment and Rugged Wheel Deck with tilt adjustments. Height....
✔️ Shifter Mount and Cup Holderintegrated into Wheel Deck.(ESR Proprietary Design).
✔️ Easily adjustable lock-down knobs. Non-Stick Polyurethane Bushings to prevent metal-on-metal sticking during adjustments. (ESR Proprietary....

✔️ Fully adjustable in any direction. Support TV/Monitors from 3x26" up to 3x37".
✔️ Back Tray for PC/Console (ESR Proprietary Design).
✔️All way adjustable including monitors Angle°, Tilt°, Height and each VESA can be adjusted separately for Angle and height. Non-Stick Polyurethane Bushings to prevent metal-on-metal sticking during adjustments. (ESR Proprietary Design)..
✔️ 5/64” Steel Tubing for ROCK SOLID stability. Extremely rugged powder coat finish..
✔️ Compatible with all ESR Cockpits, Wheel Stands and any Sim Racing Rig in the Market. Can use the stand as single TV stand.

40,000 counts resolution on primary and 10,000 counts resolution on secondary display.
L, C, R, and Z (879B & 880 only) primary measurements.
Automatic calculation of secondary parameters D, Q, Theta, ESR (Theta/ESR for 879B &880 only), and DCR (880 only).
Accuracy up to 0.1% and selectable test frequencies up to 100 kHz (880 only).
Fast auto range design for rapid, easy component measurements.

Two-channel USB digital oscilloscope, spectrum analyzer, and network analyzer (±25V, differential, 14-bit, 100MS/s, 30MHz+ bandwidth).
Two-channel arbitrary function generator (±5V, 14-bit, 100MS/s, 12MHz+ bandwidth).
16-channel digital logic analyzer, pattern generator, and protocol analyzer (3.3V CMOS and 1.8V or 5V tolerant, 100MS/s).
Two input/output digital trigger signals for linking multiple instruments (3.3V CMOS).
Additional instruments including a data logger, impedance analyzer, and power supplies.

✔️ Ships almost completely assembled. Minimal assembly effort required and 5/64” Steel Tubing for ROCK SOLID stability. Compatible and drilled for all major brands, including Logitech, Thrustmaster & Fanatec.
✔️ Folds up for easy storage and the rugged powder coat finish with anti-Slip rubber feet to prevent slipping on carpet & hardwood surfaces. (ESR Proprietary Design).
✔️ Full length Pedal Deck w/ full range mounting capabilities including angle adjustment and Rugged Wheel Deck with tilt adjustments. Height adjustable upper bar..
✔️ Shifter Mount and Cup Holder integrated into Wheel Deck.(ESR Proprietary Design).
✔️ Easily adjustable lock-down knobs. Non-Stick Polyurethane Bushings to prevent metal-on-metal sticking during adjustments. (ESR Proprietary Design).

✔️ Ships almost completely assembled. Minimal assembly effort required and 5/64” Steel Tubing for ROCK SOLID stability. Compatible and drilled for all major brands, including Logitech, Thrustmaster & Fanatec.
✔️ Folds up for easy storage and the rugged powder coat finish with anti-Slip rubber feet to prevent slipping on carpet & hardwood surfaces. (ESR Proprietary Design).
✔️ Full length Pedal Deck w/ full range mounting capabilities including angle adjustment and Rugged Wheel Deck with tilt adjustments. Height adjustable upper bar..
✔️ Shifter Mount and Cup Holder integrated into Wheel Deck.(ESR Proprietary Design).
✔️ Easily adjustable lock-down knobs. Non-Stick Polyurethane Bushings to prevent metal-on-metal sticking during adjustments. (ESR Proprietary Design).