Best Delay Switch

UCTRONICS DC 12V Time Delay Relay Module for Smart Home, Tachograph, GPS, PLC Control, Industrial Control, Electronic Experiment, Arduino Robot

  • Max. Load Voltage: terminal NC is DC 30V or AC 250V, terminal NO is DC 28V or AC 125V.
  • Functions: Supports on delay and off delay modes, the delay time can be adjusted from 0.1s to 1h, the delay mode and delay time can be set by shorting or opening the jumper pins and rotating the potentiometer..
  • Self Protection: Built with protection against reversal diode, supports anti-reverse protection. NOTE: Please remove the jumper cap of S5 when controlling AC current or DC current voltages other than 12V, otherwise the module will be burned or will not work properly..
  • Applications: This module works as a switch with time delay on and off function, highly recommended for automotive circuit modification, and LED lights, DC motors, pump and smart home control system..
Check Stock

Sensky BS010H DC 12V-30V 3A Motion Activated Sensor Switch, PIR Motion Sensor Switch with Long Distance and Time Adjustable (Black-Without Light Sensor)

  • 【Warm Tips】： To figure out your values for the Sensitivity , Please set the delay time to its minimum value first , this will save your time..
  • 【Motion Activated】 : Sensor function triggered by motion, you can use this small motion sensor switch to control lighting like Led strip lighting..
  • 【Delay Time Adjustable】: The delay time controls how long the light stays on once it gets triggered, during the delay time if motion detected, the delay time will reset and start a new delay time..
  • 【Sensitivity Adjustable】: The sensitivity controls how close you need to be to the sensor in order to activate it..
  • 【Wide Application】: You can use this sensor in different occasions like entryway lighting, cabinet lighting, gun safe lighting, pantry lighting, under the bed rails lighting..
Check Stock

Timer Relay DC 12V 24V Time Delay Relay Controller Board, PEMENOL LCD Display Digital Timer Switch Trigger Cycle Timer Module for Smart Control Power On-Off Controller

  • ...of Parameters: The current mode and parameters are clear at a glance, very clear, simple and practical. In the running interface, short press the SET button to display the current parameter settings of the system, which does not affect the normal operation of the system. In P4 ~ P7 mode, short press the DOWN key to switch the display content (running time/cycle number).
  • ★Support Button Trigger Control: The relay module delay power off and trigger delay cycle timing circuit switch Support button trigger control, high and low level trigger, switch control, suitable for most occasions.
  • ★With Reverse Connection Protection: This trigger delay cycle timing circuit switch has a key pause function, with reverse connection protection, the reverse connection does not burn.
  • ★Support UART Data Upload and Parameter Setting: You can set different OP, CL, LOP parameters, these parameters are independent of each other and saved separately. All set parameters are automatically saved after power-off. For more details, please read the user manual.
  • ★Automatic Sleep Function: In the running interface (P0~P7 mode), long-press the pause button to start or close the automatic sleep function (L-P selects on to start the sleep function, about five minutes, without any ope....
Check Stock

ENERLITES PIR Motion Occupancy Vacancy Motion Sensor Light Switch, 500W, 5A, Motion Sensor Night Light, Single-Pole, Smart LED Backlight, Neutral Not Required, Ground Required, HMOS-J-W, White

  • Motion detector light switch replaces standard switch, automatically turns connected load ON / OFF based on motion detected.
  • Smart LED backlight will turn on when motion is detected for easy location in the dark in vacancy mode.
  • Occupancy switch mode (Auto ON, Auto OFF) and vacancy switch mode (Manual ON, Auto OFF) allow you to customize the sensor according to your needs.
  • Time delay options: 15 sec (Test), 15 min, 30 min. Motion sensor will turn off after the delay time is up. Single pole use only. Not for three-way wiring.
  • Neutral wire not required, ground wire required for installation. 120-277VAC, CFL/LED: 150W, incandescent/halogen: 500W, motor: 1/8HP. Motion sensor wall switch ranges 180 Degree, 700 sq. ft. coverage. Operating temperature (32 – 131°F). UL listed.
Check Stock

TOPGREENER Dual Tech Humidity Sensor Switch, Infrared PIR Motion & Air Moisture Detection, Bathroom Fan & Light Control, Adjustable Timing, Neutral Wire Required, UL Listed, TDHOS5, White

  • FAN TIMER SWITCH Dual-tech in-wall humidity control switch that controls both bathroom fan and light simultaneously. Dual technology of passive infrared (PIR) motion sensor switch and humidity sensor switch for fan. Automate light and exhaust fan control to keep you hands-free..
  • BATHROOM FAN OCCUPANCY DETECTOR Converts bathroom ventilation fan control wall switch with this smart humidity control switch, turning fan ON automatically when humidity exceeds preset level and turning OFF as it drops to normal to eliminate excess humidity.
  • HUMIDITY SENSOR SWITCH features simple controls and operates in two modes: Occupancy Mode (auto on/off lights, auto on/off fan), and Vacancy Mode (manual on/ auto off lights, auto on/off fan). Adjustable time delay and humidity level.
  • MOTION SENSOR Two single pole switches to control bathroom light and fan separately.
  • Energy savings of up to 40% with motion sensing control.
  • 4 time delay settings from 15 sec to 30 min.
  • 120VAC, 3A fan/motors, 500W incandescent/halogen, 150W CFL/LED.
  • Up to 600 sq.ft coverage, 180 degree field of view.
Check Stock

UCTRONICS DC 12V Time Delay Relay Module with Plastic Enclosure, On Delay and Off Delay for Automobile, Raspberry Pi, Industrial Control, and Other Electronic Projects

  • Max. Load Voltage: terminal NC is DC 30V or AC 250V, terminal NO is DC 28V or AC 125V.
  • Functions: Supports on delay and off delay modes, the delay time can be adjusted from 0.1s to 1h, the delay mode and delay time can be set by shorting or opening the jumper pins and rotating the potentiometer..
  • Self Protection: Built with protection against reversal diode, supports anti-reverse protection. NOTE: Please remove the jumper cap of S5 when controlling AC current or DC current voltages other than 12V, otherwise the module will be burned or will not work properly..
  • Applications: This module works as a switch with time delay on and off function, highly recommended for automotive circuit modification, and LED lights, DC motors, pump and smart home control system..
  • You'll Be Getting: A time delay relay module U6031, 2 pieces of protective case and 2 mounting screws.
  • the plastics case keep the module free from dust and water, which is available for more applications than the separate module..
Check Stock

EarthQuaker Devices Avalanche Run V2 Stereo Reverb & Delay with Tap Tempo Guitar Effects Pedal

  • New custom-built enclosure, Flexi-Switch silent relay based switching for traditional latching or momentary operation, and updated reverb algorithm....
  • A dreamy sonic discovery device with up to 2 seconds of delay time and a lush reverb..
  • Features complete control over delay time, repeats, mix and voice (with the tone control), as well as control over the reverb length and mix.
  • It can run in one of 3 different modes to really play with your tone: Normal, Reverse and Swell.
  • Features an expression jack that can be assigned to one of six different controls using the 'EXP' selector switch.
Check Stock

Pentax Wireless Remote Control C

  • 1. Delay / Self Timer (DELAY) Just like the self timer on your camera. The timer remote switch allows you to set any delay (in 1 second increments) up to 99 hours, 99 minutes and 99 seconds..
  • 2. Interval Timer (INTVL) The Interval Timer can be set to any time period up to 100 hours as well. If you set it to 10 minutes, for example, one exposure will be taken every 10 minutes until either the film runs out or the Exposure Count limit has been reached..
  • 3. BULB/Long Exposure (LONG) It allows you to take time exposures up to 100 hours long..
  • 4. Exposure Count (N) This setting allows you to set the times of exposures that will be taken, up to a total 399 times. For example, if you set it to 30 times, then the exposure will be only taken 30 times..
Check Stock

Boss DD-8 Digital Delay Pedal

  • Delay Guitar Effect Pedal with 10 Seconds of Delay.
Check Stock