Best Cylinder End Cap

PAGOW Spark Plug Boot Wire Removal Tool Ignition Coil Puller for Volkswagenn Audi VW Hand Install Repair Tool

Best Compatibility: The spark plug wire puller installer can perfect match with Volkswagen and Audi vehicles with standard prong plug caps on each side (not recommended for non-VW/Audi plug leads). Volkswagen – New Beetle 2.0 engine AZJ (AEG), Golf IV & V 1.6 engine (AVH), 1993-2005 2.0L 4 cylinder (AZG), 1998-2006 1.8L 4 cylinder (BBW), 2006 and later 2.0L 4 cylinder turbo (BDC).
Audi – 1998-2006 1.8L 4 cylinder turbo (BEV), 2006 and later 2.0L 4 cylinder turbo (BGD)..
Size Inforamtion: The size of spark plug boot removal tool kit: 12.6inch (32cm) overall length, 3.75inch x 0.4inch x 1.2inch (9.5cm x 1cm x 3cm) handle, 9.25inch (23.5cm) shaft, 2.2inch x 0.8inch (5.6cm x 2cm) boot end..
Wide Applications: The spark plug puller tool suitable for Bora, Mercedes, Smart, and other Volkswagen and Audi vehicles with similar engines and standard prong plug caps on each side..
Easy to Use:Perform spark plug change when engine is cold to prevent the heads from stripping. After pulling the plugs, we recommend applying lubrication to make the job easier. When installing wires, refrain from pushing too hard without the tabs aligned on the tool to prevent the boot end from spreading and getting stuck..
Material:The handle of ignition coil puller is made of hard p....

PK80 MOTOR REPLACEMENT PARTS ONLY. piston kit is installed well inside of cylinder already.
better adjusting Clutch a little before riding.
High hole Piston and Long connecting rod.
Clear up the cylinder transfer ports before assembling maybe some rough slag inside which maybe break off and cause the jamming of pistons and cylinders.
fully attention on screwing cylinder to the end bottom,DO NOT screw M8 bolts tightly that maybe cause drill through the end bottom so add some gasket or washer on head is better way to prevent it happen.
Attention on piston ring if put the piston out of cylinder, the piston rings are weak, better with right way install piston kit to cylinder.

【BLASTER 200 CYLINDER TOP END KIT】Compatible with 1988-2006 Yamaha Blaster 200 YFS 200.
【SPECIAL FUNCTION】MOOSUN Blaster 200 Cylinder replacement piston sets engineered from premium materials to provide exceptional service life and....
【BLASTER 200 CYLINDER HEAD PISTON FEATURE】Cylinder piston set is the heart of engine. MOOSUN Cylinder has been factory honed and deburred to help....
【PART NUMBER】2XJ-11111-00-00, 2XJ-11311-02-00,2XJ-11181-00-00, 2XJ-11631-01-97, 3JM-11351-02-00, 3JM-13621-00-00, B8E-S0000-00-00,....
【CYLINDER PISTON RING GASKET KIT COMES WITH】1 x Cylinder, 1 x Piston, 1 x Piston Rings, 1 x Wristpin, 2 x Circlips, 1 x Needle Bearing, 1 x Head....

Compatible with or fits: (Note: Tall Cap) 1984 - 1986, 1996 Ford F-150 4.9L 6-Cylinder.
Compatible with or fits: 1995 Ford F-150 Special 4.9L 6-Cylinder.
Compatible with or fits: 1995 Ford F-150 Eddie Bauer 4.9L 6-Cylinder.
Compatible with or fits: 1993 - 1995 Ford F-150 XL 4.9L 6-Cylinder.
Compatible with or fits: 1993 - 1995 Ford F-150 XLT 4.9L 6-Cylinder | 1987 - 1992, 1996 Ford F-150 4.9L 6-Cylinder.

【Blaster 200 Cylinder Top End Kit】Fit for 1988-2006 Yamaha Blaster 200 YFS 200.
【Function】Blaster 200 Cylinder replacement piston sets engineered from premium materials to provide exceptional service life and reliability.....
【Blaster 200 Cylinder Head Piston Feature】Cylinder piston set is the heart of engine. OBUYTO Cylinder has been factory honed and deburred to help....
【Part Number】2XJ-11111-00-00, 2XJ-11311-02-00,2XJ-11181-00-00, 2XJ-11631-01-97, 3JM-11351-02-00, 3JM-13621-00-00, B8E-S0000-00-00,....
【Cylinder Piston Ring Gasket Kit Comes With】1 x Cylinder, 1 x Piston, 1 x Piston Rings, 1 x Wristpin, 2 x Circlips, 1 x Needle Bearing, 1 x Head....

Filling/Extracting Pump is designed to remove and fill brake fluid, anti-freeze, gear oil, power steering fluid and more..
Includes 1 transparent fluid syringe with locking adapter, 3adapters,2 hoses with locking cap on end, extension for deep reach and small diameter applications..
The hose attaches to quick-connect on the cylinder. Double seals for brake fluid and anti-freeze, assembled on the plunger..
Heavy-duty construction allows for strength and durability. A high quality handle help holding pump easily..

Fits Models: H27508UWK / A600006. Does NOT fit the "WL" or other series units. Part Numbers: AB-9040019, AB9040019.
40mm ID. This is for the 50mm Cylinder Bore..
This part is installed on top of the piston/connecting rod.Its purpose is to create a seal in the cylinder so that air can be pump into the compressor tank..
If this part wears your compressor will not pump the air properly.This is a wear part and it is advised to keep an extra one on hand..
This part is compatible with the following machines: Bostitch CAP2000P-OF Type 0 Air Compressor CAP2040P-OF Air Compressor CAP60P-OF Air Compressor CAP60PB-OF Air Compressor CAP1512-OF (Type 0) Air Compressor.

Filling/Extracting Pump is designed to remove and fill brake fluid, anti-freeze, gear oil, power steering fluid and more..
The pump includes two a 7-Inch by 1/4-Inch (outer diameter) hose extension for deep reach and small diameter applications, locking cap on end of hose and a 7.5-Inch/19-Centimeter clear hose..
The hose attaches to quick-connect on the cylinder. Double seals for brake fluid and anti-freeze, assembled on the plunger..
Heavy-duty construction allows for strength and durability..

Filling/Extracting Pump is designed to remove and fill brake fluid, anti-freeze, gear oil, power steering fluid and more..
The pump includes two a 7-Inch by 1/4-Inch (outer diameter) hose extension for deep reach and small diameter applications, locking cap on end of hose and a 7.5-Inch/19-Centimeter clear hose..
The hose attaches to quick-connect on the cylinder. Double seals for brake fluid and anti-freeze, assembled on the plunger..
Heavy-duty construction allows for strength and durability..