Best Common Cathode Module

uxcell Common Cathode 10 Pin 1 Bit 7 Segment 1.1 x 0.79 x 0.35 Inch 0.55\ Red LED Display Digital Tube 10pcs

  • Panel Size: 19 x 12.7 x 8mm / 0.75" x 0.5" x 0.31" (L*W*H).
  • Total Size: 19 x 12.7 x 14mm / 0.75" x 0.5" x 0.55" (L*W*H).
  • Package Content: 10 x LED Digital Display Tube.
Check Stock

uxcell Common Cathode 10 Pin 2 Bit 7 Segment 1.41 x 1.02 x 0.39 Inch 0.8\ Red LED Display Digital Tube 2pcs

  • Panel Size: 35.8 x 25.8 x 10mm / 1.41" x 1.02" x 0.39" (L*W*H).
  • Total Size: 35.8 x 25.8 x 14mm / 1.41" x 1.02" x 0.55" (L*W*H).
  • Package Content: 2 x LED Digital Display Tube.
Check Stock

uxcell Common Cathode 10 Pin 2 Bit 7 Segment 0.59 x 0.55 x 0.28 Inch 0.35\ Red LED Display Digital Tube 5pcs

  • Panel Size: 15 x 14 x 7.2mm / 0.59" x 0.55" x 0.28" (L*W*H).
  • Total Size: 15 x 14 x 13.5mm / 0.59" x 0.55" x 0.53" (L*W*H).
  • Package Content: 5 x LED Digital Display Tube.
Check Stock

uxcell Common Cathode 12 Pin 4 Bit 7 Segment 1.18 x 0.55 x 0.28 Inch 0.35\ Red LED Display Digital Tube 5pcs

  • Panel Size: 30 x 14 x 7.2mm / 1.18" x 0.55" x 0.28" (L*W*H).
  • Total Size: 30 x 14 x 13.5mm / 1.18" x 0.55" x 0.53" (L*W*H).
  • Package Content: 5 x LED Digital Display Tube.
Check Stock

uxcell Common Cathode 11 Pin 3 Bit 7 Segment 0.89 x 0.55 x 0.28 Inch 0.35\ Red LED Display Digital Tube 5pcs

  • Panel Size: 22.5 x 14 x 7.2mm / 0.89" x 0.55" x 0.28" (L*W*H).
  • Total Size: 22.5 x 14 x 13.5mm / 0.89" x 0.55" x 0.53" (L*W*H).
  • Package Content: 5 x LED Digital Display Tube.
Check Stock

WayinTop 2pcs ACS712 Hall Effect Current Sensor Module 30A Range ACS712 Module + 2pcs Voltage Sensor Module DC0-25V Voltage Tester Terminal Sensor for Arduino

  • 【Perfect Combination】Using this product can measure both voltage and current, very suitable for DIY electronic design projects..
  • 【Current Sensor Module】Chip: ACS712ELC-30A.
  • Pin 5V power supply, on-board power indicator.
  • The module can measure positive and negative current of 30 amperes, corresponding to analog output of 66mV/A..
  • 【Voltage Sensor Module】Voltage input range: DC0-25V.
  • DC input connector: Terminal cathode connected to VCC, GND negative pole.
  • Output interface: "+" then 5/3.3V, "-" then GND, "s" then the for Arduino AD pins..
  • 【Package Included】2 x ACS712 Hall Effect Current Sensor Module + 2 x Voltage Sensor Module DC0-25V Voltage Tester Terminal Sensor.
Check Stock

UMLIFE 3pcs ACS712 Hall Effect Current Sensor Module 30A Range ACS712 Module + 3pcs Voltage Sensor Module DC0-25V Voltage Tester Terminal Sensor for Arduino Raspberry Pi

  • ❃❃ Package Included：3 x ACS712 Hall Effect Current Sensor Module + 3x Voltage Sensor Module DC0-25V Voltage Tester Terminal Sensor.
  • ❃❃A wide range of applications:The current sensor ACS712 provides economical and accurate solutions for ac or dc sensing in industrial, commercial and communication systems. Typical applications include motor control, load detection and management, switching power supply and overcurrent fault protection..
  • ❃❃ACS712 Hall Effect Current Sensor Module：Chip: ACS712ELC-30A.
  • Pin 5V power supply, on-board power indicator.
  • ❃❃Voltage Sensor Module：Voltage input range: DC0-25V.
  • input : Terminal cathode connected to VCC, GND negative pole.
  • Output interface: "+" then 5/3.3V, "-" then GND, "s" then the for AD pins..
  • ❃❃Perfect Combination：Using this product can measure both voltage and current, very suitable for DIY electronic design projects..
Check Stock

horinker 2pcs MAX7219CNG MAX7219 Serially Interfaced 8-Digit LED Display Drivers，24Pins.

Check Stock

Honeywell YTH8320ZW1007/U Z-Wave Enabled Programmable Thermostat

  • Please refer Page 18 and 19 of User manual for troubleshooting steps.
  • Z-Wave delivered messages allows the thermostat to be added to or removed from a Z-Wave controller.Wire saver allows for use without a common wire..
  • Intuitive adjustment for precise comfort control, easy to use touch screen display and extra large backlit display with natural language.
  • Menu Driven programming guides the user through the programming process only showing necessary information and choices on each screen.
  • Thermostat operating message feature sends a message containing the status of the HVAC equipment.
  • The YTH8320ZW1007 includes the TH8320ZW1000 thermostat plus the THP9045A1023 wiresaver module..
  • This thermostat only connects to a z-wave communicating system (not Wi-Fi). Z-Wave delivered messages allows the thermostat to be added to or removed from a Z-Wave controller. The THP9045A1023 wiresaver module must be used when there is no “C” or common wire. A common wire is required to power the thermostat.
  • Menu Driven programming guides the user through the programming ....
Check Stock