Best Brake Cable Hose

Tektro HD-e350 eBike Hydraulic Disc Brake with 2Pcs 160/180mm Rotor

  • 【Electric Induction Control System】With power cut-off sensor, when braking, the signal is sent to the electronic control system to power off the motor. Cable length 190mm. Please pay attention to check whether the segment of the wiring port matches..
  • right rear 1850mm. This hydraulic disc brake is only suitable for ebikes. 【Oil】Non-corrosive environmentally friendly mineral oil..
  • 【Caliper】 Forged aluminum body. Open system, 2 piston. Weight Front: 302g / Rear: 322g. 【Brake Lever】:Cast aluminum lever & bracket. Two-pieces clamp. 3 finger blade..
  • 【Rotor】Diameter 180mm. Thickness 1.8mm. Weight 150g each. Lightweight polygonal guide design. High heat dissipation and heat resistance. 【Pads】High-performance metal-ceramic composites, low noise resin pad..
  • Note: the rear calipers and lever came in separate pieces so you can route internally. The brake hose were already filled with brake fluid, so you need to be careful not to spill the brake fluid when you install it..
Check Stock

SHIMANO Deore SM-BH90 Cuttable Hose - Black Front

  • Premium replacement resin coated hydraulic brake hose.
  • Stiff reinforced hose that performs under pressure, keeping your brakes sharp.
  • 2.1 mm bore diameter for excellent brake performance and response.
Check Stock

Raybestos BH380406 Professional Grade Hydraulic Brake Hose

  • Raybestos Brake Hose is designed to transfer the brake fluid from the master cylinder to the slave cylinder for braking.
  • This hose meets federal standards to ensure performance and safety, while providing longer hose life.
  • It utilizes premium fittings to ensure a good hydraulic seal.
  • Designed to transfer the brake fluid from the master cylinder to the slave cylinder for braking.
Check Stock

Raybestos BH381116 Professional Grade Hydraulic Brake Hose

  • Raybestos Brake Hose is designed to transfer the brake fluid from the master cylinder to the slave cylinder for braking.
  • This hose meets federal standards to ensure performance and safety, while providing longer hose life.
  • It utilizes premium fittings to ensure a good hydraulic seal.
  • Designed to transfer the brake fluid from the master cylinder to the slave cylinder for braking.
Check Stock

Dialed: The secret math of a perfect mountain bike setup

  • [Great Valve Package] In this package, you will get 4pcs brake lever covers and 4pcs compression nuts, 6pcs protective sleeves, 4pcs oliver and 4pcs inserts, 1 roll 2500mm bicycle hydraulic disc brake hose, 1pc bicycle hydraulic hose fitting insert tool and 1pc hydraulic hose cutter, total 25pcs. Complete kit can fully meet your needs, which is ideal for Shimano BH59 System, you don’t need to find and buy other accessories, saving your time and money..
  • [Reliable Material] Brake hose is made of high-quality material and nylon coating, which is durable and stable. 2500mm length pipes can be cut according to your needs. Precision made with fine workmanship, high temperature and low temperature resistance, high blasting coefficient and enough safe. Needle driver insertion tool is made of aluminum alloy CNC process, it feels good and durable..
  • [Hose Fitting Insert Tool] It is easy to use, super utility needle driver insertion tool. Attached hydraulic hose cutter, sharp and achieve precise and smooth cutting, clean and no burrs. Quick change adapter design, it can match with all needle driver olive and barb on the market, making maintenance easier..
  • [How to Use] You can install hose fitting cleanly and gently. First, put the olive into the oil pipe, seco....
Check Stock

4 Pieces Brake Cable Universal Bike Inner Brake Cable Housing Kit Bicycle Brake Cable Replacement for Mountain and Road Bike Gear Kit (Black)

  • Brake cable set: come with a set of brake cable kit, you get 4 pieces inner brake cables, that enough replace for your old one in long life.
  • These set are compatible to mountain bike and road bike universal.
  • Brake cable size: the cable housing is 2.5 m in length and 5 mm in thickness, the front brake cable is 1.1 m in length, the rear brake cable is 1.7 m in length, coming with cable collar, cable end and O-ring.
  • The brake cable housing kit is wear-resistant and durable, help provide safety to the cyclist.
  • Quality material: the brake housing is made with strong PVC coat coming with stainless steel cable, which improves the smoothness of the brake housing, so it is smooth and resistant.
  • It can sustain high cable tension forces without splitting, helping to stop your bike instantly.
  • The shell is made of PVC material, with resistance to cold, heat and oxidation, not easy to deform, ensure the brake sensitive, suitable for most kinds of weather conditions of riding.
  • Applicable scope: bike housing and brake cables can be applied to mountain bike, road bike, small wheel bike, foldable bike, good for maintenance and upgrading of cables.
  • Note: please cutting off no need ended and wear tail-end cap, prevent to hurt yourself.
  • You will get: the housing replacement ....
Check Stock

Sunsong 2203199 Brake Hydraulic Hose

  • Each brake hose is precision engineered to exact fit and includes brackets, grommets, molded plastic guards, wire clips, and protective sleeves as required for to ensure that all wearable parts are restored to original condition.
  • Brake hoses exceed DOT, Federal Vehicle Safety Standards (FMVSS 106) and SAE J1401 standards with a burst pressure rating of 8,700 psi, and a tensile strength of 560 lb. Durability test (Whip test) results exceed original equipment requirements by 300%.
  • All tubing is manufactured from high grade steel and electroplated with a zinc coating (chromium III), delivering superior corrosion and rust resistance against elements such as high humidity, road salt, water, and grime.
  • Every brake hose is subjected to a high pressure quality assurance test before leaving the factory, ensuring trouble free installation and operation of your new hose.
  • Brake hoses with banjo end fittings include new copper washers to ensure proper sealing.
Check Stock

2" DROP SUSPENSION & WILWOOD 4 PISTON BRAKE SET FOR 55-57 CHEVY, CURRIE REAR END, AXLES, 9" FORD POSI-TRAC 3RD MEMBER, RED CALIPERS, 12" ROTORS SPINDLES MASTER CYLINDER BOOSTER CONTROL ARMS

  • Brand New Suspension & 12" Wilwood Brake Kit For 1955-1957 Chevys with 2" Drop Spindles (Part # GMB5557X-K72). This specific set features 2" drop spindles, Rotors, and Red Dynalite 4 piston front calipers & Red Dynalite 4 piston rear calipers. Fits: 1955-1957 Chevrolet Bel Air, Delray, 150, & 210. Excludes All Station Wagons, Sedan Deliveries, and Nomads due to their Bowtie shaped gas tank that requires a centered housing rear end, as opposed to a centered pinion rear end..
  • Includes: *Currie 9-Plus Notch-Back rear end with 31 spline axles (#CE-GMB5557X): Currie crate rear ends are designed to be a bolt-in upgrade. Built to the stock 60” width & pinion specs. Heavy-duty 2" wide leaf spring pads are installed in the stock location for easy bolt-in installation *Southwest Speed 9" Ford Rear End Third Member With Posi Trac-Loc (#603-2078): This kit comes with a 3.70 ratio gear, which is a good cruising ratio. We have ratios from 3.50 to 5.00 that can be substituted in.
  • *Southwest Speed 2" Drop Spindles (SWS Part # 103-9760): SWS drop spindles provide a full 2" drop, while not changing the vehicle's steering geome....
Check Stock

MWMNUN Motor Upgraded Hydraulic Brake System The Left Of The 7/8" Handlebars 50 inch Hose Compatible with Mini Bike Baja Doodlebug DB30 Minibikes Go Karts

  • Suitable for mini bikes Baja Doodlebug DB30 mini bike karting/This kit is directly suitable for DB30 series bikes, only has a rear disc brake..
  • This Can Be Adapted To Other Minibikes/Go Karts, But Brackets Will Need To Be Fabricated. Master Cylinder Is Filled With Fluid, But May Need To Be Bled Before Use. When Mounting On DB30 Minibikes With Disc Brakes, You Must Ensure The Rotor Is Centered In The Caliper For Proper Operation. Due To Manufacturing Tolerances In These Minibikes, You May Need To Shim The Caliper To Achieve The Proper Alignment..
  • Size：This Kit Is For Using On The Left Of The 7/8" Handlebars. Brake Hose Is 50 inch.2 inch Center To Center Mount Holes On Brake Caliper..
  • The package includes: a hydraulic brake system/a pair of brake pads/a hexagonal wrench/a pair of screws/six cable ties.
  • Reminder: The Same Model May Use The Different Parts, So Please Check Your Stock One Before Place The Order.
Check Stock